SALUS PS600 Temperature Sensor User Guide
- June 6, 2024
- SALUS
Table of Contents
SALUS PS600 Temperature Sensor
Introduction
The PS600 temperature sensor measures and reports the measured temperature periodically. The measured temperatures can be used in a variety of ways depending on the system configuration: by association with cooling / heating systems, lighting systems or with the products connected to smart outlets, water valves, etc. The sensor measuring range is an important feature and it offers the possibility to use the product to send notifications related to temperature values, to create safety methods by associating with other devices, or to collect data for good analysis. operation of heating / cooling systems. This product should be used in conjunction with the Universal Gateway (UG600 / UGE600) and the Salus Smart Home application
Product Compliance
This product complies with the essential requirements and other relevant
provisions of Directives 2014/53/EU and 2011/65/EU. The full text of the EU
Declaration of Conformity is available at the following internet address:
www.saluslegal.com
2405-2480MHz; <14dBm
Safety Information
Use in accordance to national and EU regulations. Use the device as intended,
keeping it in dry condition. Product for indoor use only.
Installation must be carried out by a qualified person in accordance to
national and EU regulations.
Installation
Select a location for the sensor wall installation, if you install the sensor vertically, point the metal bracket down the mounting bracket. Horizontal installation is also possible.
For the most accurate temperature reading, the sensor must be installed in an open space, away from drafts.
-
Position the wall bracket and secure it using the supplied screws.
-
Place the sensor above the hook and slide it into position.
Location
The temperature sensor is designed to be mounted on Ø 15 mm or Ø 18 mm on the metal/plastic pipe. For the most accurate temperature reading, the sensor must be installed in an open space, away from drafts.
Additionally, the PS600 temperature sensor can be used in specific applications, such as reading the temperature value from a boiler shelf. In this case, remove the holding copper clamp and use only the body of the sensor.
| LED-SIGNAL | Descriptions |
|---|---|
| Solid at startup | Instalation, check the rese |
| 3 flashes-pause, 3 flashes-pause | Network search |
Connecting to thenetwork
Remove the electrical tape, if you have not already done so, to begin the synchronization process
OneTouch
The OneTouch feature allows you to set operating rules for your device. For the temperature sensor, for example, you can activate email alerts when the sensor reads tremperature values below those set by you.
Technical specifications
| Power Supply | CR2 lithium battery |
|---|---|
| Temperature reading interval | -50°C – 100°C |
| Cable length [mm] | 470 |
| Dimensions [mm] | 73.5 x 24.7 x 20 |
Reset
Remove the front cover.
Press and hold the side button while you reinsert the battery
Put back the front cover.
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc
reserve the right to change specification, design and materials of products
listed in this brochure without prior notice.
www.salus-controls.com
Head Office:
SALUS Controls Plc
Units 8-10 NorthfieldBusiness Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
E: sales@salus-tech.com
Documents / Resources
|
SALUS PS600 Temperature
Sensor
[pdf] User Guide
PS600, Temperature Sensor, PS600 Temperature Sensor
---|---
|
SALUS PS600 Temperature
Sensor
[pdf] User Guide
PS600, Temperature Sensor
|
SALUS PS600 Temperature
Sensor
[pdf] User Guide
PS600, Temperature Sensor, PS600 Temperature Sensor
|
SALUS PS600 Temperature
Sensor
[pdf] User Guide
PS600 Temperature Sensor, PS600, PS600 Sensor, Temperature Sensor, Sensor
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>