JUMPER JPD-BS300 Weight Scale User Manual

: July 31, 2024
: JUMPER

Table of Contents

JUMPER JPD-BS300 Weight Scale
Installing the Batteries
Download the App
Weighing Items
Precautions
Specifications
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JUMPER JPD-BS300 Weight Scale

Read this manual carefully before first use the weight scale, and keep it for future reference.

Installing the Batteries

Before measurement, you can install the batteries according to the correct battery polarity.

Download the App

Please kindly scan below QR code and download “JUMPER Health” to your phone.
Remark : Our APP is available for IOS and android device with Wireless.

Registration
Open “JUMPER Health” APP, complete the user registration, and login as instructed. Enter your nickname, gender, date of birth and height as instructed. Personal information is used to analyze your weight. To ensure the accuracy of the results, please enter accurate personal information.

Weighing

Place the scale on a hard, flat floor.
Pairing the scale. Open “JUMPER Health” APP, select “Weight” to enter the weight measurement mode. Press the scale to keep it in power on status until the scale and app pair automatically.
Please be barefoot as shown in the figure. Ensure feet to touch the four electrodes during measurement.The measurement is completed when the value on the L D screen flashing, then the measured data will be displayed on the APP.
After measurement, you can check the measured data via the “JUMPER Health” App.

Note : The weight analysis information provided by this scale is only for reference and does not constitute medical advice.

Weighing Items

Press the scale and do not measure weight until the scale turns on and returns to zero. Moving or bumping the scale may affect the accuracy, in which case you should weight again to make sure the measured data is accurate.
Auto power on when the scale is stepped-on, with a minimum weight of 3 kg for turning it on, and auto power off in 10s with no measurement.

Alert Indications
When weighing, a flashing “ Lo ” indicates a low battery level, and you should replace the batteries as soon as possible.
When weighing, a flashing “ Err ” indicates the weight being measured exceeds 200 kg, which is beyond the limit of the scale.

Converting Weight Units
Three default units available: kg/lb/st. The switch among kg, lb and st can be achieved via “JUMPER Health” App and scale.

Precautions

To prevent slipping, do not place the scale on a slippery floor, and do not use it when your feet or the scale are wet.
Always stand in the middle of the scale, to prevent it from accidentally flipping over while weighing yourself.
Only use the scale in a dry environment, and do not immerse it in water.
Wipe the surface of the scale with a damp cloth and mild detergent. Do not use any organic solvents or other chemicals.
After the batteries are depleted, immediately remove them to avoid potential leaking and corrosion.
If the scale does not work, please check the battery and ensure the battery is with correct polarity. Do not open the rear When there is no professional guidance.

Disposal and Recycling Information
The following symbol signifies that this product has to be disposed separately from ordinary household wastes at its end of life. Please kindly be aware that this is your responsibility to dispose the electronic equipment at recycling centers so as to help conserve the natural resources.

Specifications

Display : LCD display
Auto power off in 10 seconds
Weighing Units: kg / Ib / st
Weighing Range: 3 kg – 200 kg
Division : 0.1 kg / 0.2 lb
Accuracy : 3 – 50 kg: ± 0.2 kg
50 – 100 kg: ± 0.3 kg
100 – 150 kg: ± 0.4 kg
150 – 200 kg: ± 0.5 kg
Operating Temperature: 0 ~ 40°C
Dimensions : 280 x 280 x23.5 mm
Power Source: 3 x 1.5 V AAA batteries
Net Weight: 1.3 kg
6.6 – 110 lb: ± 0.44 lb
110 – 220 lb: ± 0.66 lb
220 – 330 lb: ± 0.88 lb
330 – 440 lb: ± 1.1 lb

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

US Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.