LA-Z-BOY H225764 Rowan Rocking Recliner Instruction Manual

Operating instructions

Congratulations!

You are now the proud owner of state-of-the-art Furniture by La-Z-Boy®.
You have just selected one of the finest quality upholstered products produced in the furniture industry, backed by over 90 years of quality manufacturing experience.
La-Z-Boy is proud of our designs and craftsmanship and knows you will feel the same as you enjoy your new furniture’s comfort and style.

IMPORTANT
Read these instructions thoroughly
before using your La-Z-Boy® furniture. Keep them for future reference.

Disclaimer: The information and products featured in this manual may be somewhat different from the product you purchased. La-Z-Boy reserves the right to make substitutions that are equal in quality and performance.

Important Safety Instructions

Important: Read these instructions thoroughly before using them.

DANGER– To reduce the risk of serious injury or death:

• To prevent suffocation, keep plastic bags away from children.

WARNING– To reduce the risk of burns, fire, or serious injury:

• Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas and thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery. For your safety, always use a properly installed smoke detector with working batteries.
• Closely supervise children and disabled persons using this product.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit. Move the unit into or out of the reclining position slowly, making sure that no children or pets are in close proximity.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism. To reduce the risk of head entrapment and other injuries, keep children and pets away from the openings and moving parts in and around furniture.
• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.
• Do not stand, sit, or place extra weight on the arms, back or open legrest.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the largest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• This product is intended for indoor residential use only.
• Provide a clear path for the operation of the chair, back, and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.
• This product is not intended for use as a health care device.
• Do not operate the unit until the back is installed and locked.
• Use care when moving the product. Before lifting the product, secure the mechanism to prevent unexpected opening or movement. Never move the product by the mechanism, leg rest, handle, reclining back, or swivel base. Disconnect modular units. Securely grip non-moving parts only.
• This unit is equipped with a tension adjustment feature for the reclining mechanism that is preset at the factory. The tension setting can be changed to your personal preference. To avoid tip over and insure stability, do not operate the unit with the tension adjustment wing nuts completely loosened (See Reclining Tension Adjustment Instructions).
• Do not place containers with hot beverages in the cup holders. The furniture has motion and beverages may spill and injure the occupant. Do not place oversized or uncovered beverage containers in the cup holders.

WARNING– To reduce the risk of burns, fire, or serious injury:

• Do not use La-Z-Boy® furniture in a recreational vehicle (or another moving vehicle) while the vehicle is in motion. This furniture is not intended to protect its occupant in an accident. Safely secure the furniture while the vehicle is in motion to prevent injury or damage from any sudden stop.
• If you give this product to someone else, include this Operating Instructions manual.

NOTICE: – To reduce the risk of product damage:

• Damage will occur to the mechanism if the legrest is forced closed from the 1st or 2nd position. The legrest must be extended to the 3rd position and then closed.
• Do not move the units while connected together. The purpose of the bracket system is to connect the units and prevent them from being separated while on the floor. The bracket system does not provide adequate structural support for the movement of connected units.
• Some units contain cup holders. Take care to prevent the spilling of beverages, which could result in damage to cover.

Reclining Chair Assembly Instructions

The Assembly Instructions below are for chair backs having an upholstery cover attached to all sides of the back frame. Refer to the instructions on the following pages if your chair back has a loose upholstery cover with fastening tape.

WARNING– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

Install the chair back

1. Lay the back across the arms of the body. Lift the back at a slight angle and align the brackets on the back with the brackets on the body (FIGURE 1).

2. Lower the back onto the body, making sure the back and body brackets are completely engaged.
   • To make sure the back is properly installed with both sets of back and body brackets engaged, stand behind the chair and twist the back from side to side. If one or both sides move out of position the brackets are not engaged (FIGURE 2). Remove the back and repeat the steps above.
   • If you are unable to install the back properly contact your La-Z-Boy® dealer for assistance.

3. Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).

| |
---|---|---

The Assembly Instructions below are for chair backs having a loose upholstery cover with fastening tape. Refer to the instructions on the previous pages if your chair back has an upholstery cover attached to all sides of the back frame.

WARNING– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

Install the chair back

1. Lay the back across the arms of the body. Lift the back at a slight angle and align the
   brackets on the back with the brackets on the body (FIGURE 1).
   • The back brackets may be located on the outside or inside of the back assembly.

2. Lower the back onto the body, making sure the back and body brackets are completely engaged.
   • For chairs with back brackets on the outside of the back assembly, stand behind the unit and twist the back from side to side. If one or both sides move out of position
   the brackets are not engaged (FIGURE 2). Remove the back and repeat the steps above.
   • For chairs with back brackets on the inside of the back assembly, lift the back upholstery cover to visually confirm that both sets of back and body brackets are engaged (FIGURE 3).
   • If you are unable to install the back properly contact your La-Z-Boy® dealer for assistance.

3. Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 4).
   CAUTION– To reduce the risk of minor injury:
   • Once the back is installed, the outside back upholstery cover must be secured in place at all times.

4. The outside back upholstery cover attaches to the body in different locations, depending on the style.
   • Pull the outside back upholstery cover down tight and press the fastening tape on the back upholstery cover to the fastening tape on the body (FIGURE 5).
   • Pull the outside back upholstery cover down tight and press the fastening tape on the back upholstery cover to the fastening tape on the lower seat frame. Tuck the sides in and loop the elastic strap behind the lower seat frame (FIGURE 6).

| |
---|---|---

WARNING– To reduce the risk of serious injury:

• Provide a clear path for the operation of the back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.

1. Place the furniture in the desired location; refer to Furniture Placement Guide.

2. Use a T-30 Torx driver to loosen the threaded studs to approximately 1″; this measurement may vary depending on the fabric and style. The threaded studs are located on the left side (sitting) of the right side (sitting) units.

3. Place the console (FIGURE 3) approximately 2″ to the side of the left side (sitting) rocker recliner (FIGURE 1). Position the console (with the threaded studs) slightly behind the recliner. Separate the fronts of the units to be connected, about 6″ apart. Pull the console forward until the threaded stud on the console engages in the rear bracket on the recliner.
   WARNING– To reduce the risk of serious injury:
   • The front of the unit must be raised to engage the front bracket. Please seek assistance if you are unable to lift at least 21 pounds.
   • Keep feet clear of the unit when lowering into position.

4. Lift the front of the console approximately 3″ off the ground, aligning it to the attachment bracket on the left side (sitting) rocker recliner. Gently lower the threaded stud into the front attachment bracket (FIGURE 4). Keep feet clear of the unit when lowering into position. NOTE: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to fit into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs to provide adequate clearance.

5. Place the right side (sitting) rocker recliner (FIGURE 2) about 2″ to the side of the console. Position the right side (sitting) rocker recliner (with the threaded studs) slightly behind the console. Separate the fronts of the unit to be connected, about 6″ apart. Pull the right side (sitting) recliner forward until the threaded stud on the recliner engages in the rear bracket on the console.
   WARNING– To reduce the risk of serious injury:
   • The front of the unit must be raised to engage the front bracket. Please seek assistance if you are unable to lift at least 21 pounds.
   • Keep feet clear of the unit when lowering into position.
   NOTICE: – To reduce the risk of product damage:
   • Lift from the side frame. Do not lift from the upholstery or bottom of the legrest.

6. Lift the front of the right side (sitting) recliner approximately 3″ off the ground, aligning it to the attachment bracket on the console. Gently lower the threaded stud into the front attachment bracket. Keep feet clear of the unit when lowering into position.

7. Adjust the glides on the console to level the unit, if necessary. Turn clockwise to lower and counterclockwise to raise.
   NOTICE: – To reduce the risk of product damage:
   • Do not move the units while connected together. The purpose of the bracket system is to connect the units and prevent them from being separated while on the floor. The bracket system does not provide adequate structural support for the movement of connected units.

8. The units must be disconnected before moving the loveseat. To disconnect the units, lift up the left front corner of the right side (sitting) recliner approximately 3″ to clear the front attachment bracket on the console. Move the recliner to the side before returning it to the floor. Slide the right side (sitting) recliner backward to disengage the back bracket on the console. Repeat these steps to disconnect the console from the left side (sitting) recliner.

|
---|---

WARNING– To reduce the risk of injury:
• This unit is equipped with a tension adjustment feature for the reclining mechanism that is preset at the factory. The tension setting can be changed to your personal preference. To avoid tip over and insure stability, do not operate the unit with the tension adjustment wing nuts completely loosened.

NOTICE:
– To reduce the risk of product damage:

• Make sure the legrest is closed before tilting forward and adjusting the tension.

• Do not completely tighten the wing nuts. The tension springs should not be completely compressed after making adjustments. If this occurs, the wing nuts must be loosened a
  minimum of ½-turn to avoid damage to the spring tension assembly.

• Do not completely loosen the wing nuts. The spring should not slide on the bolt after making adjustments. If the spring slides on the bolt, tighten the wing nut clockwise
  a minimum of ½-turn after the spring no longer slides on the bolt.

• Adjust both wing nuts equally.

Adjustment Instructions
You can adjust the tension of the reclining mechanism to respond to your individual size.

1. Reclina-Rocker® Chair, Reclina-Glider ® Chair, and Reclina-Way ® Chair Gently tilt the reclining chair forward to rest on its arms and top of the back. Locate the wing
   nuts, one on each side, toward the back of the recliner under the seat (FIGURE 1).
   NOTE: The Reclina-Glider ®Swivel Recliner has a thumbwheel (not shown) instead of a wing nut. La-Z-Boy Classics ® Low Profile recliner & High Leg recliner with 3-position mechanism Gently tilt the reclining chair forward to rest on its arms and top of the back. Locate the wing nuts, one on each side, toward the center of the recliner under the seat (FIGURE 2).

2. Adjust the tension by turning the wing nuts or thumb wheels in ¼-turn increments until the desired setting is reached.
   • A taller or heavier person may choose to increase the reclining tension by tightening the wing nuts or thumb wheels clockwise.
   • A smaller person may choose to decrease the reclining tension by loosening the wing nuts or thumb wheels counterclockwise.

3. Return the reclining chair to the upright position. Test the new setting. Make additional adjustments if needed following these steps.

|
---|---

3-Position Legrest Operating Instructions

WARNING– To reduce the risk of serious injury:
• Provide a clear path for the operation of the back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

NOTICE:
– To reduce the risk of product damage:
• Damage will occur to the mechanism if the legrest is forced closed from the 1st or 2nd position. The legrest must be extended to the 3rd position and then closed.

To Operate the Legrest

1. Your La-Z-Boy® chair is equipped with a three-position locking legrest for customized seating comfort. Simply pull on the handle rotating it counterclockwise to control the legrest (FIGURE 1). You may stop in any one of three ideal positions. The 1st position is slightly inclined to relaxing reading (FIGURE 2). The 2nd position is slightly more inclined to comfortable television viewing (FIGURE 3). The 3rd position is fully extended for complete relaxation (FIGURE 4). To lower the legrest, rotate the handle counterclockwise to the fully extended position, then rotate clockwise to the fully closed position.
2. The chair back can be reclined with the legrest closed or extended. To recline, apply pressure to the back. Sit upright to return the back to an upright position.
3. Bring the back upright and close the legrest before getting out of the unit.
   Feature of the Reclina-Rocker®
   The chair body can be tilted back when the legrest is in use. Shifting your body weight rearward will cause the chair body to tilt backward offering a number of different positions.

Reclina-Glider® Swivel Recliner & Complements Swivel Glider Instructions

To Activate the Swivel Feature

1. Turn the unit on its back.

2. Locate the two spacer bushings, two truss head screws, and swivel base bottom (FIGURE 1).

3. Remove the two truss head screws using a T-30 torx driver while holding the swivel base bottom steady.
   NOTE: The two polyethylene washers are attached with adhesive and do not need to be removed.

4. Remove the two spacer bushings from between the swivel base bottom and glide base subassembly (FIGURE 2).

5. Return the chair to the upright position.

6. Store parts for future use to deactivate the swivel feature.

To Deactivate the Swivel Feature

1. Turn the unit on its back.
2. Rotate the Swivel Base Bottom until the holes on the Swivel Base Bottom line up with the holes on the Glide Base Subassembly (FIGURE 2).
3. Hold the swivel base bottom steady. Place the spacer bushings between the holes in the Swivel Base Bottom and the Glide Base Subassembly. Insert the truss head screws through the holes in the Swivel Base Bottom, through the spacer bushings, and into the holes in the Glide Base Subassembly. Fasten each screw using the T-30 torx driver.
4. Return the chair to the upright position.

Furniture Placement Guide

WARNING– To reduce the risk of serious injury:
• Provide a clear path for the operation of the back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.

Reclining Units
To place your reclining unit the proper distance from the wall, fully recline the unit and leave a minimum of 2″ of space between the top of the back and the wall (FIGURE 1).
Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference. Interference with the legrest may cause it to not close completely (FIGURE 2). If the legrest is not closed completely, it may pop out unexpectedly and could cause injury. Proper clearance for an area rug is demonstrated in FIGURE 3. Make sure tables and other items are at a safe distance to avoid interference with the operation of the legrest. Improper placement of a table could cause the occupant to become trapped in the unit; this is demonstrated in FIGURE 4. There must be enough clearance for the legrest to be fully extended before closing.

Cup Holder Cleaning Instructions

Care and Cleaning Instructions for the Cup Holder
The finish on the cup holder can be damaged during use or cleaning. It is recommended that a coaster be used to reduce the chance of damage and that the cleaning instructions be followed. Use water and mild soap, such as dish soap, to clean the cup holders. Dry immediately and thoroughly with a soft clean cloth to maintain the finish. The use of harsh, abrasive cleaners is not recommended and must be avoided.

Ia-z-boy.com
La-Z-Boy Incorporated One La-Z-Boy Drive Monroe, MI 48162
©2018 La-Z-Boy Incorporated
93000287-00 Rev. 07/18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>