CASHWAY CSW-M783 Dog Training Collar with Electric Collar User Manual

CSW-M783 Dog Training Collar with Electric Collar
User Manual

Congratulations on buying this training collar, if for any reason you are not 100%satisfied with your training collar, please contact our customer service immediately so that we can help you. Please read the manual carefully before use.

Package List

Introduction of appearance

1: Electric shock key 2: Vibration key 3: Beep 4: Lighting key 5: Switch 6: Lock key 7:Charging port 8/9: Intensity adjustment key 10: Antenna 11: Highlighted LED floodlight 12:Launch indicator 13: Latch 14: Receiver on / off key/learning key 15: charging port 16/ 17: shock contact 19: status indicator

Features

1. Easy to operate, use + or – key to quickly adjust the intensity of electric shock, vibration and beep.
2. Four modes: electric shock, vibration, beep and LED mode, which can meet different training requirements.
3. This product can control one or two receiving collars.
4. Open area can be controlled within 300 meters.
5. Waterproof design.
6. Power-saving design, The receiver automatically enters the power-saving state of sleep in the 3-minute static state and wakes up quickly when moving.

Charging

1. Remote control charging
   Insert the charging cable Micro terminal into the remote control, insert the other terminal into the charger, and then connect to the power supply to start normal charging.  The battery symbol on the LCD screen starts to flash and stops flashing after a full charge.

2. Receiver charging
   Insert the charging line Micro terminal into the receiver, insert the other terminal into the charger, and then connect to the mains to start normal charging. Red LED lights on, full power red LED lights off, green LED lights on.

About 2-3 hours can be full of power

Remark:

Please choose the matching charger, try to choose the charger of 5V/0.5A- 5V/1A, otherwise, it is easy to damage the product.
The remote is paired with the receiver

1. First, put the newly purchased product into sufficient power, then turn on the receiver (collar), press the power button on the receiver, you will hear a tick, and the green light will start to shine, shining once in about 3 seconds. In the boot state, long-press the power switch on, green light for about 1 second 3 speed shiny, shiny said in pairing mode, there are 10 seconds, to operate the key of electric shock and vibration on the remote control key, beep key pairs for learning, according to the three function keys, the red LED will light up on the remote control, loosen the button LED lights, transmit a signal to go out to receive said. After 10 seconds of pairing, the green light will stop flashing quickly and turn to slow flash and enter standby mode.
2. Select two receivers for pairing. After completing the first pairing, switch the remote control [ ] button once and press it briefly to switch to another receiver mode.

If no match is successful, it may be caused by external environmental factors, please operate twice more. Again, please contact the nearest distributor or customer service personnel.

Control various functions

First install the collar belt, as shown below, and then put it on the pet properly.

1. The shock
   Short press the [ ] button on the remote control, the receiver will receive the electric shock function instruction, and the receiver will start the electric shock to realize the electric shock function. Press once and the function starts for 1-3 seconds.

2. Vibration
   Press the [ ] button on the remote control, the receiver will receive the vibration function instruction, and the receiver will start the vibration sense to realize the vibration function.
   Press once and the function starts for 1-3 seconds.

3. Beep
   Press the [ ] button on the remote control, the receiver will receive the function instruction of beeping, and the receiver will start beeping to realize beeping. Press once and the function starts for 1-3 seconds.

4. Lighting
   Long press and hold the [ ] button on the remote control, and the high- brightness LED light on the remote control will light up to realize the function of lighting or guidance.
   Loosen the button and the LED light will go out.

Strength level regulation

The shock, vibration, and beep functions can be adjusted by the [+] and [-] keys on the right side. Level 0 is closed, level 8 is the strongest, and the working time is also the longest. The appropriate strength grade may be selected as required.

Matters needing attention

1. Please for this machine for repairing or change, if you have any questions please contact the dealer or customer service products.
2. To avoid collision fall or strong native, do not too much you push hard on the LCD screen, otherwise may cause damage of the LCD screen or display abnormal.
3. For disputes caused by the illegal use of this product or for damage repair, the company is not responsible for.
4. Avoid collars in pets for more than 12 hours a day.
5. In pet neck collars, it is suggested that in 1-2 hours at most.
6. Check belt loops, prevent excessive tension, a graphic operation that takes a manual, please relax appropriately.
7. If you have found a burr, pet skin or discontinue use until the better continue to use again.
8. Battery time according to different function operation habit, so you need to watch the light on the receiver and battery symbol on the LCD screen, timely and sufficient power.
9. The effective distance of the controller is referred to the linear distance, remote control and receiver middle without obstacles, if there is interference or signal shielding, will affect the actual distance may be different.
10. Training positive is not recommended, the time is too long, about 20 minutes at a time.

This product adopts 433MHZ wireless remote control transmission operation and the host machine adopts wireless 433MHZ receiving to realize long-distance instruction operation of 300 meters. It is the best choice for pet training and the safest pet flow training tool. The correct choice can effectively train the pet without causing any harm to it.

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>