Wenzhou Morning Electronics WSEUNX Smart Switch User Manual
- June 6, 2024
- Wenzhou Morning Electronics
Table of Contents
Wenzhou Morning Electronics WSEUNX Smart Switch User Manual
Product Description
This new designed glass panel wireless touch smart switch is designed with
WiFi+RF to replace traditional switches with a variety of ways to control.Now
one new smart feature as multi-control association to other smart switches is
added into the Smart Life/Tuya App,together with the backlight on/off and
relay status.And its scratch resistance glass panel is suitable for different
decoration styles with its best value.
Note: Button sound on and off: no button operations before operations
begin within 6 seconds.Then press switch button for 4 times and long press for
the fourth time until the switch beep sounds as Di-Di for 2 times for
successful operation.
Safety Information
Risk of Electric Shock:Electricity can cause personal injury and property damage if handled improperly. lf you are not sure about any part of these instructions,please seek professional assistance from a qualified electrician.
Technical Parameters:
- Model : WS-EU-RF / WS-US-RF
- Working voltage:100-240V AC, 50Hz/60Hz
- **Max. total current:1*** (pure resistive load) 2.5A (inductive and capacitive load)
- Max. Load Power:depends on voltage
- Wireless type: WIF12.4G+RF433MHz(Rx)
- Working temperature: Ot-40°C
- Support system: Android/iOS
Warnings:
Turn off the power at the circuit breaker and test that power is off before wiring.
Installation
Note:
- Make sure that the power at the circuit breaker is off before wiring.
- Neutral Wire is required.Confirm the wall box contains a Neutral Wire(typically while If the wall box don’t have a Neutral Wire,please try another location at your home or call a professional electrician to install the switch.
- The wire colors indicated in this manual are the usual colors and may differ in some houses.
- Ensure the wire conductors are securely fastened to each wire.
- Ensure the Wi-Fi signal is steady and normally working before wiring.
- If you don’t have any wiring experience,please call a professional electrician.
Step 1
- Turn off the circuit breaker and use the electrical tester to test the power.
- Ensure the switch is off before wiring.
Step 2
- Remove the existing wall plate;turn on the power at the circuit breaker and use an electrical tester to check which wire is line wire;the tester will flash and or chirp when it comes close to a line wire.
- Turn off the power at the circuit breaker and use the electrical tester if the power is off, and then pull the existing switch out;label the line wire and other wires;dis-connect the wires from the existing switch with pliers.
- Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.
Step 3
- Mount the switch with the provided screws and snap the wall plate on it.
Step 4
- Turn the power back on at the circuit breaker and then switch the light on.
Add Devices
Download Smart Life App
Registration or Log in
- Download “Smart Life”Application
- Enter the Register/Login interface;tap “Register” to create an account by entering your phone number to get verification code and “Set password”.Choose “Log in” if you already have a Smart Life account.
Configure the APP to the switch
- Preparation:Ensure the switch has been connected with electricity;ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.
Note:
The switch only supports 2.4G network.lf you have connected 5G network,please disconnect 5G network firstly and connect 2.4G network.
Wi-Fi link method:
Pair and clear up the WiFi code(New Updated)
-
Make sure your phone is connected to Wi-Fi and Bluetooth.
-
Open Smart Life/Tuya App and Click”+”,then the prompt page will automatically show on the screen.Click “Go to add”.
-
Select the device you want to add and click “Add”
-
Enter Wi-Fi Password and click “Confirm”,waiting for completing the connection.
-
Add the device successfully, you can edit the name of the device to enter the device page by click “Done”
How to reset/repair Wi-Fi code
Press the switch button for 6 times,and hold on the 6th time,then release
until you hear Di-Di-Di(3 times),and the blue indicator on the switch will
flash fast after 3 seconds.Reset/repair is successful.
Remote radio frequency (RF)link method:
Pair and clear up the RF code
How to pair the RF code
(can be turned on and off):
Confirm your switch is off before operations.Press the switch button for about
8 seconds until you hear Di-Di(2 times).Then the matching of RF code is
successful. The key of the remote controller can control the switching of the
state of the switch on and off corresponding to the position of the switch.
(Open only):
Confirm your switch is off before operations.-Press the switch button for
about 5 seconds until you hear Di(1 time).After that,release the button, press
the corresponding button on the remote control to turn on.Then the matching of
RF codes is successful. The key of the remote controller can control the
corresponding position of the switch to be open.
(Close only):
Confirm your switch is on before operations.-Press the switch button for about
5 seconds until you hear Di(1time).After that,release the button, press the
corresponding button on the remote control to turn on.Then the matching of RF
codes is successful.The key of the remote controller can control the
corresponding position of the switch to be closed.
How to clear up the RF code
Confirm your switch is off before operations. Press the switch button for a long time until you hear Di-Di-Di-Di(4 times), and then release the button.The RF code is now cleared up. KB
How to achieve multi-control association
Note:Please confirm you have successfully finished the WiFi link method above for adding this switch to your Smart Life App before the association.
-
WiFi add another smart switch to the same Smart Life/Tuya App.(If there is a smart switch having been added before to the app,just go to next step.)
Note:There is no need to wire the new added switch to the light,only L and N are required for wiring. -
Then you will see two devices in the app and click the main switch(as One gang switch as below) by entering into the next operation.
-
Click in the upper right corner and choose”Multi-Control Association, and then click “+” in the right corner
-
- Choose the switch that you want to associate to and then choose the switch button that you want to control the same light.
-
Then go back to previous page,you will see two items in the page,one is your main switch,the other is the one you associate just now.
Note:Please confirm the associated switch is enabled. -
Now you are able to control your light with two switches. Do not associate another button in the same switch for multi-control.
-
If you want to add another third or more smart switches to control your light,just repeat the steps above.And you will see the result as below when you associate another new switch.
Set your Echo speaker by Alexa APP
-
If you have finished installing Smart Life,just open Amazon Alexa App;log into your Alexa account with password.
-
Click the menu on the top left -click “settings”,choose “Set up a new device”(choose a device like Echo)
Note:
When below page appears,long press the small dot on your Echo device until the light turns to yellow.Then click “Continue”on the App.
Attention:The mobile phone can not open a variety of VPN software. -
Choose your own Wi-Fi and wait for a few minutes.After watching an introduction video,click “next step”,then it will enter Home page automatically.Now the Echo has been connected to Wi-Fi successfully.
Enter Smart Life Skill in Alexa APP
Choose “Skills” in the options bar, and then search “Smart Life” in the input box.
Then input the user name and password of Smart Life APP that you have
previously registered.
Now you can use your Alexa to control your Smart devices.
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause hajimful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure compliance statement:
This device has been evaluated to meet the general RF exposure requirement