FIAMMA VENT 28 F Rooflight Instruction Manual
- June 6, 2024
- FIAMMA
Table of Contents
FIAMMA VENT 28 F Rooflight
Check that nothing has been damaged or deformed during transport.
In the event of doubts or questions concerning the installation, use or
limitations of the product, contact the dealer. We recommend that the
installation is carried out by qualified personnel and in compliance with
current local regulations.
-
Decide where the rooflight should be installed and make a square hole of 28cm.
The rooflight can be installed on roofs with thickness between 28 and 68mm. -
Seal the lower part of the external frame with a minimum width of 10 mm by following the appropriate rails. Recommended sealant: SIKALASTOMER-710 / THEROSTAT II / DEKALIN 1512.
-
Place the external frame in the opening hole making sure that the hinges are facing the front of the vehicle.
-
Fix the frame with the screws (using the correct screw in relationship with the roof thickness).
- Screw Ø3,5×30 mm to use for roof thickness between 28 – 40mm.
- Screw Ø3,5×50 mm to use for roof thickness between 40 – 50mm.
Tighten the screws in order to bring the frame adherent to the roof, check that the frame hasn’t been deformed.
-
Mount the mosquito net frame using the special pressure hooks.
Remove the protective plastic applied to the cover (do not expose the product to sunlight for too long to avoid to make this operation difficult).
In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website for spare parts drawing.
Fiamma declines all responsibility for any personal injury and damage to
property due to incorrect assembly or use of the product; it is suggested to
keep the instructions inside the vehicle.
The assembly of the product must be carried out according to the assembly
instructions: the product must not be modifi ed in any way.
Before proceeding with assembly, check that the roof thickness is compatible
with the product.
Before choosing the place where to assembly the rooflight, check that:
- the product doesn’t interfere with adjacent accessories (luggage racks, cables, reinforcements in the roof, cabinets inside the passenger compartment).
- the internal and external surface of the roof is flat.
Periodically check the tightness of all the screws in the rooflight, especially after the first kilometers from the installation and always before and after long trips. If the opening-closing device hardens, lubricate the lid opening device with a few drops of grease. It is forbidden to walk on the product cover.
Before starting the vehicle, check that the rooflight is properly closed. Periodically check that the cover is intact. Don’t open the rooflight when the vehicle is travelling. Don’t open the rooflight in case of strong wind or rain. Remove snow or ice from the rooflight. The maximum permitted speed of the vehicle with a mounted rooflight is 130 km/h. Always comply with speed limits and the Highway Code. The speed should always be suitable to traffi c conditions and transported load.
CARE AND MAINTENANCE
For the internal and external cleaning of the rooflight, always use only neutral, non-aggressive detergents. For cleaning the Crystal cover use an acrylic glass cleaner with a soft cloth so as not to scratch the surface. Never use aggressive products such as glass cleaners, all-purpose cleaners, abrasives or dish-washing detergents. Also, never use alcohol-containing detergents, solvents or any corrosive liquid. The mosquito net can be cleaned with water and a neutral detergent by removing it from the press fittings.
Warranty Fiamma
In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.
Fiamma S.p.A. – Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)
All rights reserved.
Fiamma S.p.A.
reserves the right to modify at any time, without notice, prices, materials,
specifi cations and models or to cease production of any model.