vtech VG208-0 DECT 6.0 Accessory Handset User Manual
- June 6, 2024
- vtech
Table of Contents
- vtech VG208-0 DECT 6.0 Accessory Handset
- Important safety instructions
- SAVE THESE INSTRUCTIONS
- ECO mode
- The RBRC seal
- FCC, ACTA, and IC regulations
- FCC Part 68 and ACTA
- Industry Canada
- What’s in the box
- Install the battery
- Connect the charger
- Charge the battery
- Display icons overview
- Handset overview
- LCD language setting
- Before use
- Operating range
- Need help?
- Limited warranty
- Technical Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
vtech VG208-0 DECT 6.0 Accessory Handset
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
- Read and understand all instructions.
- Follow all warnings and instructions marked on the product.
- Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
- CAUTION: Do not install the telephone base at a height above 2 meters.
- Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, or in a wet basement or shower.
- Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
- Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes.
- Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.
- This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or office, consult your dealer or local power company.
- Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.
- Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
- To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
- Do not overload wall outlets and extension cords.
- Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:
- When the power supply cord or plug is damaged or frayed.
- If liquid has been spilled onto the product.
- If the product has been exposed to rain or water.
- If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
- If the product has been dropped and the telephone base and/or handset has been damaged.
- If the product exhibits a distinct change in performance.
- Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
- Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a fire or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
- Only put the handset of your telephone next to your ear when it is in normal talk mode.
- The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
- For pluggable equipment, the socket outlet shall be installed near the equipment and shall be easily accessible.
- CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the handset. Use only the supplied rechargeable batteries or replacement batteries (BT162342/BT262342) for the handset. Do not dispose of batteries in a fire. They may explode.
- Do not use the battery in following conditions:
- High or low extreme temperature during use, storage or transportation.
- Replacement of a battery with an incorrect type that can defeat a safeguard.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- A battery is subjected to extremely low air pressure that can result in an explosion or the leakage of flammable liquid or gas.
- Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
SAVE THESE INSTRUCTIONS
Battery
-
Use only the batteries provided or equivalent. To order a replacement, visit our website at www.vtechphones.com or call 1 800-595-9511. In Canada, go to
phones.vtechcanada.com or call 1 800-267-7377. -
Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions.
-
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
-
Exercise care in handling batteries in order not to create a short circuit with conductive materials.
-
Charge the battery provided with this product only in accordance with the instructions and limitations specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a
multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food and
Drug Administration, WTR recommends to physicians that:
Pacemaker patients
- Should keep wireless telephones at least six inches from the pacemaker.
- Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.
- Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.
About cordless telephones
- Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.
- Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.
- Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR often reduces or eliminates the interference.
- Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger.
- Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.
ECO mode
This power-conserving technology reduces power consumption for optimal battery performance. The ECO mode activities automatically whenever the handset is synchronized with the telephone base.
The RBRC seal
The RBRC seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada. The program provides
a convenient alternative to placing used nickel-metal hydride batteries into
the trash or municipal waste, which may be illegal in your area. VTech’s
participation makes it easy for you to drop off the spent battery at local
retailers participating in the program or at authorized VTech product service
centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery
recycling and disposal bans/restrictions in your area.
VTech’s involvement in this program is part of its commitment to protecting
our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA, and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a
Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.
To ensure the safety of users, the FCC/ISEDC has established criteria for the
amount of radiofrequency energy that can be safely absorbed by a user or
bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC/ISEDC criteria. The handset may
be safely held against the ear of the user. The telephone base shall be
installed and used such that parts of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirements:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical
requirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among
other things, a product identifier in the format US: AAAEQ##TXXXX. This
identifier must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to the premises wiring and
the telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally be used for
connecting to a single line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are
called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the REN is
0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or
less. For more information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired
alarm dialing equipment connected to your telephone line, ensure the
connection of this equipment does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
service provider or a qualified installer. If this equipment is
malfunctioning, it must be unplugged from the modular jack until the problem
has been corrected. Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement procedures,
follow the instructions outlined under the “Limited warranty”.
If this equipment is causing harm to the telephone network, the telephone
service provider may temporarily discontinue your telephone service. The
telephone service provider is required to notify you before interrupting
service. If advance notice is not practical, you will be notified as soon as
possible. You will be given the opportunity to correct the problem and the
telephone service provider is required to inform you of your right to file a
complaint with the FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or procedures that could
affect the proper functioning of this product. The telephone service provider
is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing
aid compatible. If this product has memory dialing locations, you may
choose to store emergency telephone numbers (e.g., police, fire, medical) in
these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging
up.
Perform such activities in off-peak hours, such as early morning or late
evening.
Industry Canada
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this telephone. The
term ‘’IC:‘’ before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The
REN is an indication of the maximum number of devices allowed to be connected
to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the
RENs of all the devices does not exceed five.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
California Energy Commission Battery charging testing instructions
This telephone is set up to comply with the energy-conserving standards right
out of the box. These instructions are intended for California Energy
Commission (CEC) compliance testing only. When the CEC battery charging
testing mode is activated, all telephone functions, except battery charging,
will be disabled.
To activate the CEC battery charging testing mode:
- Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with charged batteries before proceeding.
- While you press and hold /FIND HANDSET, plug the telephone base power adapter back to the power outlet.
- After about 10 seconds, when the IN USE light starts flashing and the telephone base shows Registering… and then De-register?, release /FIND HANDSET and immediately press it within two seconds.
When the phone successfully enters the CEC battery charging testing mode, all
handsets display To register HS… and …see manual alternately.
When the phone fails to enter this mode, repeat steps 1 to 3 above.
To deactivate the CEC battery charging testing mode:
- Unplug the telephone base power adapter from the power outlet, and then plug it back in. Then the telephone base is powered up as normal.
- Press and hold /FIND HANDSET on the telephone base for about four seconds until the IN USE light turns on and the handset shows Registering.
- 3. Press QUIET# on the handset. The handset shows Registered, and you hear a beep when the registration process completes. This process takes about 60 seconds.
What’s in the box
Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.
Install the battery
Connect the charger
Charge the battery
Battery indicators | Battery status | Action |
---|---|---|
• The screen is blank, or shows Put i n charger and flashes. | • | |
The battery has no charge or very little charge. The handset cannot be used. |
• Charge without interruption (at least 30 minutes).
• The screen shows a Low battery and flashes.| • The battery
has enough charge to be used for a short time.| • Charge without
interruption (at least 30 minutes).
• The screen shows HANDSET X.| • The battery is charged.| •
To keep the battery charged, place it in
the handset charger when not in use.
Display icons overview
Handset overview
See the manual of VG208/VG208-2 for details.
LCD language setting
If you accidentally set the LCD language to Spanish or French, press MENU and then enter 364# to change the handset LCD language back to English while the handset is not in use.
Before use
Add and register a handset
You can add new VG208-0 handsets (purchased separately) to your VG208/VG208-2
telephone system. Your telephone system supports a maximum of 5 handsets.
Each handset must be registered with the telephone base before use. When first
purchased, each expansion handset displays To register HS… and … see manual
alternately.
NOTES
- Charge the new handset without interruption for at least 30 minutes before registering it to the telephone base.
- You cannot register a handset if any other system handset is in use.
Register a handset
Press and hold /FIND HANDSET on the telephone base for about four seconds
until the IN USE light turns on and it shows Registering…. 2. Press QUIET # on
the handset. The handset shows Registering…. Both the telephone base and
cordless
handset show Registered, and you hear a beep when the registration process
completes. This process takes about 60 seconds.
If registration fails, Failed appears on the handset screen. The handset shows
To register HS… and see manual alternately, and the telephone base returns to
idle mode. This may take up to five minutes to occur. Please start again from
Step 1.
Deregister handsets
If you want to replace a handset or reassign the designated handset number of
a registered handset, you must deregister all the handsets and then
individually register each handset. If you want to register a handset to
another telephone base, you must deregister all handsets, and then register
each handset individually to the desired telephone base.
Deregister all handsets from the telephone base
- Press and hold /FIND HANDSET on the telephone base for about 10 seconds until the IN USE light on the telephone base starts flashing and the telephone base shows Registering… and then De-register?.
- Release /FIND HANDSET and immediately press it again within two seconds.
- All handsets display To register HS… and see manual alternately when the deregistration process completes. The deregistration process takes about 10 seconds.
NOTES
- If the deregistration process fails, you may need to reset the system and try again. To reset, unplug the power from the telephone base and plug it back in.
- You cannot deregister the handsets if any other system handset is in use.
- Even if the battery is depleted, you can still deregister the handsets by following the steps. After the handset is charged for at least 10 minutes, the screen shows To register HS… and see manual alternately.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset displays Out of range or no pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well when you press . Move closer to the telephone base, and then press to answer the call. If the handset moves out of range during a telephone conversation, there may be interference. To improve reception, move closer to the telephone base.
Need help?
For operations and guides to help you using your telephone, and for latest information and support, go and check the online help topics and online FAQs. Use your smartphone or mobile device to access our online help.
- Go to https://help.vtechphones.com/VG208-0; OR
- Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help. If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.
You can also call our Customer Support
at 1 800-595-9511 [in US] or
1 800-267-7377 [in Canada] for help.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof
of purchase (“Consumer” or “you”) that the Product and all accessories
provided in the sales package (“Product”) are free from defects in material
and workmanship, pursuant to the following terms and conditions, when
installed and used normally and in accordance with the Product operating
instructions. This limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will replace at VTech’s option, without charge, a Materially Defective Product. If we replace the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the
date of purchase. If VTech replaces
- a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or
- (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
- The product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or another liquid intrusion.
- The product that has been subjected to contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like; but then only to the extent the damage was not caused by incorrectly securing the waterproof handset’s protective elements, for example, failing to properly close a seal), or such protective elements are damaged or missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond its stated specifications or limits (e.g. 30 minutes in 1 meter of freshwater).
- The product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech;
- Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems;
- Product to the extent that the problem is caused by use with non-VTech accessories;
- Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible;
- Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes);
- Product returned without valid proof of purchase (see item 2 below); or
- Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at
www.vtechphones.com or call 1
800-595-9511.
To obtain warranty service in Canada, go to phones.vtechcanada.com or dial 1
800-267-7377.
NOTE: Before calling for service, please review the user’s manual – a
check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of
the Product(s) to the service location.
VTech will return replaced Product under this limited warranty.
Transportation, delivery or handling charges are
prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the
Product failure is not covered by this
limited warranty, or proof of purchase does not meet the terms of this limited
warranty, VTech will notify you and
will request that you authorize the cost of replacement prior to any further
replacement activity. You must pay for
the cost of replacement and return shipping costs for the replacement of
Products that are not covered by this
limited warranty.
What must you return with the Product to get warranty service?
- Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and
- Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
- Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech.
It supersedes all other written or oral communications related to this
Product. VTech provides no other warranties for this Product. The warranty
exclusively describes all of VTech’s responsibilities regarding the Product.
There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such
modification. State/Provincial Law Rights: This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to
state or province to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited to one year
from the date of purchase. Some states/ provinces do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to
you. In no event shall VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but not limited to lost profits
or revenue, inability to use the Product or other associated equipment, the
cost of substitute equipment, and claims by third parties) resulting from the
use of this Product. Some states/ provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any
damage or loss resulting from the use
of this user’s manual. VTech Communications, Inc. and its suppliers assume no
responsibility for any loss or claims by
third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road – Ste 555, Tigard, OR 97223, United
States
Phone: 1 800-595-9511 in the U.S. or 1
800-267-7377 in Canada
Technical Specifications
- Frequency control Crystal controlled PLL synthesizer
- Transmit frequency Handset: 1921.536-1928.448 MHz
- Channels DECT channel: 5
- Nominal effective range
- Maximum power allowed by FCC and IC. The actual operating range may vary according to environmental conditions at the time of use.
- Power requirement Handset: 2.4 V DC, AAA×2, Ni-MH battery
- Charger: 6V DC @ 0.4A
- Memory Phonebook: 50 memory locations; up to 30 digits and 15 characters Caller ID log: 30 memory locations; up to 24 digits and 15 characters
- Call block: 150 entries
References
- VTech Cordless Phones | DECT 6.0 Phones | Best Home Phones - VTech® Cordless Phones
- VTech Cordless Phones Official Site | Best Home Office & Business Phones
- VTech Cordless Phones Official Site | Best Home Office & Business Phones
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>