COSTWAY FP10068US Wall Mounted Electric Fireplace User Manual
- June 6, 2024
- COSTWAY
Table of Contents
COSTWAY FP10068US Wall Mounted Electric Fireplace User Manual
Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
US: cs.us@costway.com
UK: cs.uk@costway.com
Before You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the area in
which they will be placed in use, to avoid moving the product unnecessarily
once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from babies
and children as they potentially pose a serious choking hazard.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, injury to persons, fire hazard and will void the warranty.
Please read the Installation & Operating Instructions before using this appliance.
CAUTION
PRODUCT DAMAGE MAY OCCUR.
Never attempt to disassemble or alter the product in any way not instructed by
this manual.
USER INSTRUCTION
Before use
Check that the air intake and exhaust is not covered or obstructed in
anyway.
Keep combustible objects at least 3ft away from the unit.
Plug the unit to a grounded power socket.
Grounding
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock.
This unit comes standard with a 6ft (1.8ml long, three wired cord. Always plug
the unit into a wall outlet. An extension or relocate tab should never be
used.
CAUTION! WARNING: Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
CAUTION! WARNING: DO NOT modify the plug provided with the product nor using any bypass device if the plug does not fit the outlet. Have a proper outlet installed by a qualified electrician.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
- Read all instructions before using this fireplace.
- Always unplug this appliance when not in use.
- Children should be advised not to play with this fireplace.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Any repairs to this appliance should be carried out by qualified/authorized service personnel only.
- Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced with original “OEM” (original equipment manufacturers) parts only.
- Do not use outdoors.
- This appliance is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate this appliance where it may fall into a bathtub or other water container.
- Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic areas and where it will not be tripped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Connect to properly grounded outlets only.
- This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electric codes, or for USA installations, follow local codes and the National Electrical Code, ANSI/NFPA No. 70.
- There is a thermostat limiter inside the fireplace. When the inner temperature overheats or abnormal heating occurs, the thermostat protective device will cut off power supply to avoid damage to the fireplace or risk of fire.
- This appliance has hot and arching or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it.
- Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- The use of an extension cord is not recommended due risk of fire. If used the extension cord shall be No. 14 AWG minimum size and rated no less than 1875 watts, and the extension cord shall be a three-wire cord with grounding type plug and cord connector. The extension cord shall not be more than 20 ft (6 m) in length.
- Do not use this appliance with a programmable timer or any other device that switches the appliance on and off automatically. In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by an utility.
- This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.
SPECIFICATIONS
PACKAGE CONTENTS
INSTALLATION GUIDE
Planning Installation
Before you begin assembly, locate the instructions and hardware. Compare
all parts with the Hardware Included Package Contents lists. Be sure you have
all the parts and can identify them. A helping hand is always good. Assemble
your fireplace with an adult assistant if possible. Some pieces are heavy and
will need to be held by a helper. Assembly time will take approximately 5-20
minutes.
Before assembly, use scissors to unwrap the parts from the packaging. Do not
use a box cutter or exacta-knife, as you may cut into the heater pieces inside
the box and damage the finish. Check for the red hardware bag located inside
the packaging, taped to the top of the box. Do not discard any pieces. Use an
appropriate screwdriver to insert and tighten all screws.
CAUTION: This carton includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
Electrical Connection
WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock, and injury to persons.
WARNING: Do not use this fireplace if any part of it has been under water. Immediately & call a qualified service technician to inspect the fireplace and replace any part of the electrical system which has been under water.
A 15 Amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this appliance. Preferably, the appliance will be on a dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the fireplace is in operation. The unit comes standard with a 6 ft (1.8 m) long 3-wire cord, exiting out the back of the fireplace. Plan the installation to avoid the use of an extension cord. If an extension cord must be used, it must be a minimum No. 14 AWG, 3-wire with grounding type plug and connector, and must be rated not less than 1875 watts. The extension cord shall not be more than 20 ft (6 m) in length.
This remote control requires 1 Lithium Coin Cell Battery (size CR2025), which is included.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING: DO NOT mix old and new batteries.
DO NOT use rechargeable silver oxide cell batteries with remote control unit.
DO NOT mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium)
batteries.
DO NOT dispose of batteries in fire. Improper disposal may cause batteries to
leak or explode.
Tools Required (not included)
Hardware Included
The first way of hanging on the wall
- Choose a solid wall. Position the mounting bracket (C) where the electric (A) is to be installed on the wall, and ensure that the mounting bracket
(C) is level.
Use a pen to mark the 4 mounting holes on the wall at the desired mounting location, using the mounting bracket (C) as a template.
- Insert the 4 self-drilling wall anchors (CC) into the wall where previously marked. If installing the mounting bracket (C) to a wall stud, there is no
need to drill the holes in the wood and no need for the plastic wall anchors (CC). It is recommended to install the mounting bracket to at least one stud.
- Secure the mounting bracket (C) to the wall using 4 large screws (BB).
The second way of standing on the table.
- Attach the left bracket (G) to the Left foot base (F) using 3 large screws (DD).
- Attach the Right bracket (D) to the Right foot base (E) using 3 large screws (DD).
- Use a screwdriver to secure the mounting (A) to the left and right table top stand with 4 small screws (AA).
OPERATING INSTRUCTIONS
Using the Manual and Remote Controls
The upper right corner of the electric fireplace (A) is the control panel. The button on the front of the electric fireplace(A) has the same function as the remote control (B). The effective range of the remote control is up to 13 feet.
- Power Button
- Flame Control Button
- Heater Control Button
- Timer Control Button
- Digital Display Panel
Check that the heater outlet grill is not covered or obstructed in any way,
and make sure the power to the unit is switched on. The fireplace can be
accessed in two ways: Using the touch control panel, or using the
multifunction remote control unit.
Press the corresponding button to operate your fireplace:
Using the Power Button
Using the Flame Control Button
- Press the flame control button (2) to turn on the ember bed and flame effect.
- Pressing the flame control button (2) once turns flames on and lights the ember bed.
- Pressing the flame control button (2) again will cycle through different colors of the ember bed. The color rotation mode will cycle through different color settings continuously. the table for more detailed information.
Using the Heater Control Button
Using the Timer Control Button
Heater Locking Function
To turn off mode, press and hold the power button for 10 seconds to enter
heat lock out mode. Flame lights will flash 6 times to signal the function is
turned off and locked out. To turn on mode, press and hold the power button
for 10 seconds. The flame lights will flash6 times and the function will be
restored. When the heat button is pressed in lock out mode, the ember bed will
flash 6 times until the heating mode is turned on.
CARE AND MAINTENANCE
(i) IMPORTANT: Always unplug the power cord before cleaning the unit. Allow the unit to cool before cleaning it.
- Wipe the exterior surface of the electric occasionally with a soft, damp cloth (not dripping wet), and dry the exterior surface before operating.
- Do not immerse the electric fireplace in water.
- Do not use any cleaning chemicals such as detergents and abrasives.
- Do not allow the interior to get wet, as this could create a hazard.
- Light accumulated dust may be removed from the electric fireplace with a soft, dry cloth.
- To store the electric fireplace, put it back into its original packaging and store in a clean, dry place.
- The blower and flame motor are pre-lubricated for a durable using time and need no further lubrication or maintenance. Dust particles will accumulate on/in the electric fireplace, so periodic cleaning/vacuuming of the electric fireplace is recommended.
- Always turn the heater OFF and unplug the power cord from the outlet before cleaning.
- Cleaning behind the front glass can be done by removing the front glass from the engine assembly. There are two screws on each side of the engine that hold the glass in place. Remove the four screws that hold the glass and then lift the glass up and away from the engine assembly. While holding the glass, disconnect the control panel wire harness from the engine assembly. Clean with a lint free damp cloth. To replace the glass, center the glass over the engine assembly and reconnect the control panel’s wire harness to the engine assembly and lower the glass until it seats. Install the four screws that you removed into the brackets on each side of the glass. Tighten all the screws.
Front Glass Removal
Front Glass Installation
CAUTION: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
Battery Replacement
Procedure
Battery Size CR2025
Disposal of Used Batteries
The battery may contain hazardous substances which could endanger the environment and human health. This symbol marked on the battery and/ or packaging indicates that used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about the recycling of used batteries, please contact your local municipality waste disposal service.
DANGER
Disconnect power before servicing.
****Any electrical re-wiring of this appliance must be done by a qualified electrician. This wiring must be done in accordance with local codes and/or in Canada with the current CSA C22.1 Canadian Electrical Code, and for US installations, the National Electrical Code ANSI/NFPA No. 70.
WARNING: Disconnect power before servicing.
Welcome to visit our website and purchase our quality products!
this product and giving us valuable feedbacks.
With your inspiring rating, COSTWAY will be more consistent to offer you
EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
US office: Fontana, California
UK office: Ipswich
- Reward Points
- Exclusive Customer Service
- Personalized Recommendations
- Permanent Shopping Cart
- Order History
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>