rako RLED150CV1 1 Channel Constant Voltage Dimmer Instruction Manual

rako RLED150CV1 1 Channel Constant Voltage Dimmer

Specifications

• Product Name: RLED150CV1
• Type: 1 Channel Constant Voltage Dimmer
• Version: 2.0.0 (2024)
• Compatibility: Works with Rako Wireless system and Rako Wired system
• Installation Options: Ceiling or Surface Mount
• Maximum Load:
  • 12V DC: 150W
  • 24V DC: 300W

Product Usage Instructions

Installation of the RLED150CV1

1. Installation should only be carried out by a competent electrician.
2. Do not connect directly to a 230V supply.
3. RLED150CV1 modules should be mounted in ventilated, dry areas.
4. Mount the modules vertically or horizontally with proper ventilation.
5. Ensure modules are easily accessible for maintenance purposes.
6. Installation Steps:
7. Remove the cover and the cable clamp.
8. Connect the DC power supply to the ‘IN’ terminals and load cable to the ‘OUT’ terminals.
9. Replace the cable clamp and ensure cables are firmly in place.
10. Replace the cover.

Initial Checks

• Upon powering up, the load should dim up to full brightness.
• The clear button acts as a manual on/off switch with an LED indicator for wireless messages.

Programming the RLED150CV1

After testing the device with the setup button, follow the Wireless Module Setup Guide for programming instructions.

FAQ

Q: How can I tell if the unit is receiving wireless messages successfully?

A: When receiving messages successfully, there will be four rapid pulses on the LED indicator.

Q: What happens if the unit is out of range for wireless reception?

A: If out of range, there will be intermittent pulses on the LED indicator when messages are sent.

For more information relating to the RLED150CV1 see the Wireless Module Application Sheet , Wireless RAK Application Sheet, and Wireless Device LED Diagnostics .
For programming a wireless system, including the device in this manual: Wireless Module Programming Guide

What is the RLED150CV1?

The RLED150CV1 is a Wireless single Channel constant voltage dimmer designed for constant voltage LED loads. With its built-in receiver, the RLED150CV1 works with a Rako Wireless system and a Rako Wired system.
The RLED150 can be programmed from an RCM keypad, or via Rasoft Pro using a programming tool (RAMPI or HUB).
Ceiling installation or surface mount installation is available for the RLED150CV1, For surface mount installation, a bracket is provided.
requires a WK-HUB in range of the RLED150CV1

Loadings

NB Loads should be tested before being connected to the RLED150CV1.

Installation of the RLED150CV1

WARNING
Installation should only be carried out by a competent electrician.

Do not connect directly to a 230V supply.

• RLED150CV1 modules should be mounted in areas which are adequately ventilated, dry, and outside of any enclosed metal casings that may interfere with the Wireless signal.
• Modules should be mounted vertically, with the terminals at the bottom, or horizontally, with ventilation slots at the front.
• Do not obstruct the ventilation slots.
• While the modules are designed to be completely maintenance-free, they should be mounted in an accessible location should investigation or re-addressing be necessary.

Initial Checks

When the module powers up, the load should dim up to full brightness.
The clear button can be used as a manual on/off switch. The internal LED behind the clear button will flicker when the module receives any Rako Wireless message and is a useful diagnostic indicator. This function becomes inactive after 20 minutes to avoid a nuisance l ight spill but can be re-activated by pressing the clear button.

Programming the RLED150CV1

Once the RLED150CV1 has powered up and has been tested working with the setup button, the device is ready to be programmed. For instructions on how to program the RLED150CV1, see the Wireless Module Setup Guide .

Appendix 1: LED Diagnostics

Appendix 2: Wiring Example

The diagram below shows an example of how the RLED is to be connected.
Please check with the power supply manufacturer for compatibility before installing it with an RLED product.

Thank you for choosing Rako Controls; we hope that you are pleased with your system. Should you require further assistance, please contact us via our website, www.rakocontrols.com, or by calling our customer support helpline on 01634 226666.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>