Serta 0330 76 Inch Rolled Arm Sofa Instruction Manual
- June 6, 2024
- Serta
Table of Contents
PRODUCT GUIDE & ASSEMBLY INSTRUCTIONS
Rolled Arm Sofa
So comfortable, you’ll feel the difference the moment you sit down.
Should you prefer to speak with a customer service representative, you may
call toll free:
1-855-372-2315
Guidelines
FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY
- Do not stand on the item or use it as a step ladder
- Do not use this item unless all bolts and screws are firmly secured and fastened.
- Check all bolts and screws every 90 days. As necessary tighten if any are loose.
- Lift up then move. Pushing over or dragging this product can result in an injury or cause damage to the floor and piece.
WARNING:
DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF INJURY.
Pre-Assembly Preparation:
Please read through this instruction booklet before beginning the assembly of
this item.
Two adults are recommended for assembly.
- Clear out the space for assembly and layout of all parts on Parts List, extra room will allow you to easily determine if all the pieces are present.
- Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
- Keep small parts and pieces away from children and pets until fully assembled.
- Please check for any loose screws and tighten them before you use.
Parts List
Step 1
Remove all parts from the carton and place them on a protected surface or carpet. Place the Arm and Seat Frames (1 & 2) upside down and open the bottom flap. Take the Back Cushions (7), Side Legs (B), Middle Legs (C), Flat Washers (D), T-Nuts (E), Back Frames (3 & 4) and Thumb Bolts (A) out of the seat box.
Step 2
Turn over the Arm and Seat Frame with “R” Label (2) and slide the Back Frame with “R” Label (4) into the seat frame until fully engaged. Align the holes of the Back Frame (4) to the Arm Frame (2) and secure with one Thumb Bolt (A).
Step 3
Turn over the Arm and Seat Frame with “L” Label (1) and slide the Back Frame with “L” Label (3) into the seat frame until fully engaged. Align the holes of the Back Frame (3) to the Arm Frame (1) and secure with one Thumb Bolt (A).
Step 4
Move the two assembled parts together. Align the holes of Seat Frames (1 & 2) and Back Frames (3 & 4) to the other side and secure with one Thumb Bolt (A) to the back frames. Thumb Bolts (A), Flat Washers (D), and T-Nuts (E). Ensure all Thumb Bolts (A) are completely tightened.
Step 5
Secure the bottom and back flaps with hook and loop tape.
Remove the plastic caps on the threaded bolts of each leg.
Attach the Side Legs (B) to the corners of the sofa. Then screw the middle
legs（C）in the frame as the sketch shown.
Step 6
Open the vacuum-packed Seat Cushions (5) by carefully cutting the bags with a
pair of scissors. Insert the Back Cushions (7) into the appropriate Back
Covers (8). Insert the Seat Cushions (5) into the appropriate Seat Covers (6).
Remember to keep the top side of the Seat Cushions (5) with the top side of
the Seat Covers (6). Fluff all cushions to allow them to expand. Lastly,
position all cushions on the sofa. Seat and back cushions may take 24-48 hours
to fully expand, which will allow wrinkles and indentations caused by packing
to fade.
Note: There is a hook and loop strip between the back cushions and the
back frame. Please stick them according to the location.
ATTENTION: To close the zipper, please follow Diagram 1.
Failure to follow this could result in damage to the zipper.
Limited Warranty
The manufacturer’s products are warrantied against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as the party or entity which purchases this manufacturer’s furniture from an authorized retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned products.
The manufacturer warrants its products to be free from defects in materials and workmanship (normal wear and tear, fading and stretching excepted), for one year from the date of purchase, except as provided below under the limited warranty.
The exceptions or exclusions to this warranty are as follows:
- Any warranty claim that is submitted after the limited warranty period, or without proper proof of purchase will not include the cost of parts, labor, or delivery.
- This warranty shall not apply to the manufacturer’s products that have been subjected to misuse, neglect, alteration, modification, or attachments, either caused by the Original Purchaser, shipping, storage, accident, fire, flood, or acts of God.
In the event of a defect in material or workmanship covered by this warranty, the manufacturer will repair or replace, at their discretion, without charge the warrantied parts within a reasonable amount of time. We reserve the right to require damaged parts be returned to us upon request. Natural markings such as scars, brands, grain variations, wrinkles, color variations, etc. will be considered normal characteristics and not construed as defects.
For claims or questions concerning this warranty, please contact the customer service department on the web at www.trueinnovations.com. Be prepared to provide your name, address, daytime phone number, the model and purchase order number of the product, date of purchase, and the website where it was purchased. The manufacturer requires that the original sales receipt be submitted with all requests to confirm that you are the Original Purchaser according to our written warranty.
This warranty gives you specific rights, and you may also have other rights, which vary from state to state (or country to country). All warranties are limited to the Original Purchaser for normal use. Should you prefer to speak with a service representative, you may call toll-free: 1-855-372-2315 (U.S.) or 0-800-051-6775 (U.K.).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>