KILOVIEW M2 H.264 HDMI VGA Video Encoder User Guide
- June 6, 2024
- KILOVIEW
Table of Contents
KILOVIEW M2 H.264 HDMI VGA Video Encoder
PACKING LIST
Packing list
One M2 video encoder, one power supply [DC 12V/1A), one user manual, one
product certification.
ATTENTION :
The actual pack int, list may be different since the product updating.
DEVICE INTERFACES
NOTE:
Users can connect USB storage, USB to RS232/RS485 converter to the USB port.
DEVICE INSTALLATION
Connect the power adapter
Using the power adapter [DC 12V/1A) connect to the device, afterthe power is
turned on, the device starts working.
Connect network
Connect one end of the network cable to the encoder’ s Ethernet port. The
other end is connected to the network switch or the computer’s Ethernet port.
LED INDICATOR DESCRIPTIONS
Power up
After powered up, LINK/RUN will be off, and PWR will be on. Indicator
lights will go to below status, which lasts 10-155.
**RUN/LINK/PWRindicators
**
CONNECT AUDIONIDEO SIGNAL
Connect analog audio signal
Through 3.5mm audio cable, it can be accessed analog audio signal You can
select the analog audio as audio encod ng source,reter to “Select
video/audio signal source”. The analog audio output is not declared for
current software. I
SELECT VIDEO/AUDIO SIGNAL SOURCE
Click “Audio&Video Ajdustments > Video Source and Adjustrrent” or
“Audio&Video Adjustments > Audio Source and Adjustment” in the Web console,
you can select video and audio source.
Video/Audio source options:
WEB DEFAULT LOGIN IP ADDRESS AND
Default IP Address
The default IP address of encoder is 192.168.1.168
with subnet mask 255.255.255.0. You can login the Web
console to change the network addresses.
Login the Web console
Open your web browser and access : http://
RTSP STREAMING
The RTSP service is always enabled for the device. All the decoders which
support RTSP protocol and H.264 decoding can connect and get stream from the
device.
The defauIt RTSP accessing URL is:
rtsp //<device 1p address>/chOl rtsp //
NOTE:
‘chCl’ , ‘subOl’ is the RTSP session ID. You can change the session ID in the
Web console.
RTMP LIVE STREAMING
Add streaming service:
Our device’ s H.264 main/sub stream supports adding up to 8 same or different
streaming services, to meet your needs of adopting same/different stream media
protocols for multi-goal streaming pushing. On the management interface
of”Encoding & Stream”> “Encoding and Stream Settings”, click “add a stream …
“, you can add your needed streaming service.
RTMP live streaming (push)
Currently, most live streaming platforms (e.g. YouTube) require “RTMP Pushing”
protocol. After adding “RTMP pushing” service, click set icon to configure
RTMP parameters.
On the configuration page:
“Push point” requires an URL which RTMP push lo. Take ‘You Tube’ for an
example, you can get the URL like bellow:
RESTORE FACTORY SETTINGS
- Restore factory setttings:
If users change parameters that lead encoder couldn’ t work ( typical situation is to change network address, so that it couldn’ be visited encoder by network), users could restore factory setting to default value.
Two methods for restoring factory settings:
- Choose “Basic Se,ti ngs > Restore factory settings” on the web console @ Hold ‘RESET’ button:
- Hold the ‘RESET’ button more than 3 seconds.
- Restoring factory setting will lead to the device reboot, restarting course will last about 20S.
NOTE:
These parameters will be restored after restoring factory setting:
- The password of admin will be reset to admin;
- The IP address will be reset to 192.168.1.168 and subnet mask is 255.255.255.0;
- All the video/audio encoding settings will be reset;
- Streaming settings will be reset.
FIRMWARE UPGRADING
Firmware upgrading
This device supports online firmware upgrading for upgrading software. Select
”Ha sic Settings”, pull downward and click”Update firmware”. On the page,
click “Browse” to select the upgrading file, and click “Upgrade” to upgrade
the device.
NOTES:
- After u pleading firmware f le successfully, the encoder will automatically restart, this process will takes about 30s-60s (the time will be different according to upgrade content), and please be patient.
- After the upgrade is complete, via the Web interface “system informatior>version information” to check whether the latest version information in accordance with expected to confirm the upgrade is successful.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>