KILOVIEW E1-s HD-3G-SDI Wired Video Encoder User Manual
- June 4, 2024
- KILOVIEW
Table of Contents
KILOVIEW E1-s HD-3G-SDI Wired Video Encoder User Manual
Packing List
-
Device ×1
-
Power Supply×1
-
Warranty Card×1
-
Quick Start Guide×1
Device Interfaces
- Power port
- Mini USB
- 3.5mm line in/out
- SDI Input
- SDI Loop
- 100M Ethernet port
- Working indicators
- USB expansion port
- Micro SD/TF slot
- Power on /off
- Reset
Device Indicator
LED Indicators | Name | Color | Status | Description |
---|
Power
|
Red
| ON| Power connected
OFF| Power off or failure
Signal
|
Green
| ON| SDI signal connected
OFF| SDI signal unconnected
Run
|
Green
| Flashing| Working
ON| Starting
OFF| Device is abnormal or not started
Device Connection
Note
- Please use the equipped power adapter to power the device. Other unqualified power supplies may damage the device.
- Under encoding mode, please make sure the camera is connected to the SDI IN port.
- Loop is not a must, you can connect to the SDI OUT port when loop out is needed.
Device Discovery
Use the free tool —ONVIF Device Manager
Download the ONVIF Device Manager for free
Visit the website https://sourceforge.net/projects/onvifdm/ to download and
install ONVIF Device Manager. Please follow the software operation guidelines
for the download method/installation.
ONVIF Device Manager is a network video app for managing network video, network video storage and network video analysis. Realize services such as discovery device, media, imaging, analysis and PTZ.
Step 1: Start ONVIF Device Manager, all devices in the network can be
found in the left device list.
Step 2: Click the device in the device list, the device information will
be displayed in the information bar.
Introduction
- Access method: Open a web browser and enter in the address bar: http://device IP address/ (the device IP address is the IP address of the E1-s displayed in the device list).
- The working network that the device is connected needs to support automatic acquisition of IP (DHCP). After the device automatically acquires the IP, it can be discovered by the software through Onvif.
Solution for the device cannot be found.
If the device can’t be found in the network with the above two methods due to
the network environment,
please kindly try to access the device by its default IP address
192.168.1.168. That is to say, enter http://192.168.1.168/ in the browser to
enter the Web UI.
Website for more information on E1-s video encoder
https://www.kiloview.com/en/support/
Login to the device WEB page
Enter to the Web page of the device, both the user name and password are admin by default.
Note
- To ensure information security, it is recommended to change your password immediately after logging in for the first time!
- Due to the browser compatibility issues, it is recommended to use Chrome, Firefox or Edge.
Device Working
Video source checking
When there is no video signal input, the Motion JPEG stream displays a blue
image. If the video input, there will be a real-time video displayed and
changes every three seconds.
Note
If the video source connected, there is still a blue screen or video displayed
abnormality. Please check the input video source, the video resolution format
or cables, etc.
Encoding streams checking
Download the VLC
Download and install the VLC through the official address
https://www.videolan.org/vlc/. Please follow the official guidelines of VLC
for the download /installation.
VLC is a free, open source, cross-platform multimedia player and framework that can play most multimedia files, as well as DVD, CD, VCD and various streaming protocols
- Click the “Encoding and Streaming” – “Encoding and Streaming Parameter Settings”;
- In the H.264 stream, copy the URL address displayed on the right side of RTSP;
- Open “Media” —-“Network Streaming” of VLC;
- Enter the URL address of RTSP in the network, and click the [Play] button in the lower right corner;
- VLC will play the input video of device.
RTMP Pushing streaming live
First, add an RTMP push point on the device side. Click “Encoding and Media
Streaming” — “Encoding and Streaming Parameter Settings”, and then click “Add
a Streaming Service” under the H.264 main stream, and select “RTMP Push” in
the pop-up window “. After confirmed, a push pint is generated.
Take FACEBOOK as an example, first obtain the RTMP push URL on the live platform. Login to FACEBOOK, click “Live Video” to enter the live room, and click “Use Stream Key” for live broadcast. Fill in the URL of live broadcast and Stream Key into the URL address of the RTMP push point, and start the streaming service. You can see the video in the live broadcast room.
Introduction
- If the platform RTMP streaming address and live broadcast code are separate, please use the symbol “/” to add the live broadcast code after the RTMP address. The format is: rtmp address/live code.
- Please make sure the device is connected to the network, and configure the correct IP address, DNS and other.
Parameters
Website for more information about the E1-s streaming service:
https://www.kiloview.com/en/support/docs/E1-s/
Firmware Upgrading
Download upgrade firmware
Kiloview will continue to provide the firmware of updating functions and
fixing bug for E1-s, please visit:
https://www.kiloview.com/en/support/download/
Select “video encoders” > “E1-s”, find and download the latest firmware.
Upgrade device firmware
Login to the web page of E1-s, click “Settings”– “Firmware Upgrade” to check whether the latest irmware version downloaded is higher than your current version. If yes, select the downloaded firmware and click “Firmware Upgrade”.
After uploaded the firmware successfully, it needs to reboot the device. After
clicking “ok”, the device will restart, please be patient.
Note
- Please not power off during the upgrade process, otherwise the device couldn’t work.
- Generally, it will take 3-5 minutes to upgrade the device. If it’s still not completed after 5 minutes, please try refreshing webpage, if you still can’t access it, please try to contact technical support.
Restore factory settings
If the device cannot work normally after modified the parameters or forgot internet IP configuration and couldn’t search and find the device, please restore factory settings.
Two methods for restoring factory settings:
- If you can login to web page, then via the WEB page, click “Settings—System settings–Restore factory settings”.
- If you can’t login to web page, press the RESET button for 5 seconds in the bottom of device.
Note: After restoring factory setting, below parameters will be turned to default value:
- Login username and password will be “admin”;
- IP address will be restored as 192.168.1.168, subnet mask will be 255.255.255.0;
- All encoding parameters of video and audio will be restored to default value;
Others
To prolong the device life,please unplug the power and keep it properly if you do not use it for a long time.
Contact US
For more questions, please contact us via:
https://www.kiloview.com/en/support
KILOVIEW Electronics CO., LTD.
Tel: 86-18573192787
Email:support@kiloview.com
Web: www.kiloview.com/en
Address: B4-106/109, Jiahua Intelligence Valley Industrial Park, 877
Huijin Road, Yuhua District,
Changsha City, Hunan Province, China.
References
- ODM download | SourceForge.net
- Support and Help Center – Kiloview
- E1-s Wired Encoder – Kiloview
- Download Center – Kiloview
- Official download of VLC media player, the best Open Source player - VideoLAN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>