JANUS TX2000 Digital Wireless Keypad Instruction Manual
- June 6, 2024
- JANUS
Table of Contents
TX2000 Digital Wireless Keypad
ModelTX2000 Wireless Keypad
Installation Instruction
specification
Power : 4.5V (AAA*3) Operating Freq : 315MHz Operating Power consumption: 14mA
Modulation Type : ASK
1
V1. Nov 2020
Box Contents
Digital Wireless Keypad
Screw Plug Mounting Screws Screw Anchors For Convenience, program Keypad
BEFORE mounting. To begin use, firstly remove insulation from battery
compartment. Please refer to 6. Changing Batteries instructions.
Remove insulation
2
1. Setting Your Wireless Keypad Master PIN
NOTE: The Master PIN MUST be reset to begin use. A. Activate programming mode:
Press the factory preset default PIN
– While in PROG mode, both & are on
Press – Beep to signal Master PIN selected, & flashing for PIN input
Enter your New PIN (4 to 8 digitsMUST BE numbers other than 1234),then press
Re-Enter your New PIN to confirm,
then press
again.
Two beeps to signal Master PIN has now been successfully changed – Keypad will automatically exit PROG mode after 20 seconds
IMPORTANT: Please write down your designated PIN below and keep this instruction manual in a secure place for future reference.
If Master PIN is lost and unrecoverable, the keypad is required to be return
to factory and a reset fee is applicable.
3
2.Keypad Door Operation Key Setting
A. Programming Single Door Installation
The above jumper configuration will allow on the keypad to be coded. NOTE: The
jumpers are located on the Control Box Printed Circuit Board. Please refer to
the control box instruction manual. B. Programming Single Door Installation
This above configuration uses all three keys. Open Stop Close 4
C. Two or Three Door Installations
Door 1 C/Box1 Jumper configuration for Door 2 C/Box2 Jumper configuration
for Door 3 C/Box3 Jumper configuration for
5
3. Code Setting to Controller
Once the key configuration is set, you can now program in the security code
from your keypad.
On the control box, press the LEARN code key once Learn LED indicator will
light Enter your PIN, then press Press the door operation key that will
operate the
door. e.g.: for A. single door installation, you would press Learn LED will go
out The wireless keypad is now programmed to the control box NOTE: To program
more than one wireless keypad to the control box, repeat the above
instructions.
IMPORTANT: If a wireless keypad is lost or stolen, please refer to control box
instruction manual for procedures to erase the code memory.
6
4. Mounting Instructions
Mount the keypad in clear view of the door with the two screws supplied
Push in the screw cover to conceal the top screw
Remove battery for the affixing of bottom screw. Refer to 6. Changing
Batteries
Use the screw anchors supplied if required
7
5. Keypad Operation
Enter the keypad PIN
4-8 digits PIN – LED is on if PIN correct Press the designated keypad
operation key
– LED will remain on for 20 seconds for consecutive door operations, without
re-entering the PIN.
6. Changing Batteries
1. Remove the battery cover by sliding downwards 2. Remove the low batteries
and dispose of it properly
3. Install 3 new AAA 1.5V alkaline or lithium batteries,note the +/-
polarities indicated in the batterycompartment
4. Replace battery cover by sliding upwards
8
7. Optional Secondary PIN Operations
The GLIDEROL Digital Wireless keypad allows for up to 10 individual PIN’s to
be programmed (CODE 01-10), which can be used for different family members or
to act as a temporary PIN for house-sitters, visitors or service people. Below
is instruction to set a secondary PIN for CODE 06 (Replace 06 with other CODE
numbers 02-10 as required).
NOTE: CODE 01 is the MASTER PIN
Enter MASTER PIN (4 to 8 digits), then press to enter PROG Mode
Press
to select Code 06
– & flashing for PIN input
Enter your PIN for Code 06 (4 to 8 digits), then press
Two beeps to signal Code 06PIN has now been successfully set
– Keypad will automatically exit PROG mode after 20 seconds
9
8. Erasing a Secondary PIN
Below is instruction to erase a secondary PIN for Code 06 (Replace 06 with
other Code numbers 02-10 as required).
NOTE: Code 01 is the MASTER PIN and cannot be erased
Enter MASTER PIN (4 to 8 digits), then press to enter PROG Mode
Press
to select Code 06
– & flashing for PIN input
Press
to erase
Two beeps to confirm Code 06 PIN has now been successfully erased
– Keypad will automatically exit PROG mode after 20 seconds
10
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation. Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help.
RF warning statement: The device has been evaluated to meet general RF
exposure requirement. The device can be used in portable exposure condition
without restriction.
11
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>