Ohsung Electronics S904-SD-WF WiFi Module User Manual
- June 6, 2024
- Ohsung Electronics
Table of Contents
Ohsung Electronics S904-SD-WF WiFi Module
Features
General
- IEEE® 802.11 b/g/n (20MHz/40MHz) (1×1) solution
- Integrated PCB antenna
- SIZE : 48mm x 28mm x 10mm
- CMOS MAC, Baseband PHY, and RF in a single chip for 802.11 b/g/n compatible WLAN
- Complete 802.11n solution for 2.4GHz band
- 72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth
- 150Mbps receive PHY rate and 150Mbps transmit PHY rata using 40MHz bandwidth
- Compatible with 802.11n specification
- Backward compatible with 802.11b/g devices while operating in 802.11n mode
Ordering Information
Model | Description |
---|---|
S904-SD-WF | 802.11 b/g/n (HT20/HT40) Module |
Product Specifications
Electrical Specifications
Absolute Maximum Ratings
Description | Min. | Typ | Max. | Unit |
---|---|---|---|---|
Storage Temperature | -30 | +80 | ℃ | |
Storage Humidity (40℃) | 85 | % |
Operating conditions
Description | Min. | Typ | Max. | Unit |
---|---|---|---|---|
Supply Voltage | 4 | 5 | 6 | Vdc |
Ambient Temperature | -20 | +70 | ℃ | |
Ambient Humidity (40℃) | 85 | % |
Standard Test Conditions
The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance
Ambient Condition
Description | Min. | Typ | Max. | Unit |
---|---|---|---|---|
Ambient Temperature | 20 | 30 | ℃ | |
Ambient Humidity (40℃) | 60 | 70 | % |
Power Supply Voltages
Input power | Unit |
---|---|
VDD_5V | 5V ± 0.5V |
Current Consumption
Device state| Code rate| Output
power, dBm
| Current consumption
---|---|---|---
Min| Max
ON_Transmit
| 802.11b 11Mbps| 17| 180mA| 260mA
802.11g 54Mbps| 15| 130mA| 180mA
802.11n MCS 7 (HT20)| 14| 120mA| 170mA
802.11n MCS 7 (HT40)| 14| 110mA| 150mA
ON_Receive
| 802.11b 11Mbps| N/A| 50mA| 80mA
802.11g 54Mbps| N/A| 50mA| 80mA
802.11n MCS 7 (HT20)| N/A| 50mA| 80mA
802.11n MCS 7 (HT40)| N/A| 50mA| 80mA
ESD Information
ESD | Unit |
---|---|
Air discharge | ±8KV |
Contact discharge | ±4KV |
Standard Rated Specification
Radio Performance under Typical Conditions: VDD @ 5.0V, temp. 25°C
Division | Characteristic |
---|---|
WLAN Standard | IEEE 802.11 b/g/n HT20/40, Wi-Fi compliant |
Host Interface | USB |
Frequency Range | 2.400GHz ~ 2.4835GHz (2.4GHz ISM Band) |
Dimension | L x W x H : 48 x 28 x 10 (typical) mm |
Modulation | 802.11b : DQPSK, DBPSK, CCK |
802.11g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK
Data Rate
| 802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
Data Rate (20MHz, 40MHz)| 802.11n: MCS0, MCS1, MCS2, MCS3, MCS4, MCS5, MCS6,
MCS7
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
-
- The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for reevaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: OZ5-S904-SD-WF”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how
to install or remove this RF module in the user’s manual of the end product
which integrates this module. The end user manual shall include all required
regulatory information/warning as show
in this manual.
ISED Canada (IC) Statement
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
RF Radiation Exposure Statement :
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Required end product labeling:
Any device incorporating this module must include an external, visible,
permanent marking
or label which states: “Contains IC: 21703-S904SDWF”
This radio transmitter (identify the device by certification number or model
number if Category
II) has been approved by Industry Canada to operate with the antenna types
listed below with
the maximum permissible gain indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>