vtech VM3262 Pan and Tilt Video Baby Monitor User Guide
- June 6, 2024
- vtech
Table of Contents
VM3262 Pan and Tilt Video Baby Monitor
Credits: The Background Noise sound file was created by Caroline Ford, and is
used under the Creative Commons license. The Stream Noise sound file was
created by Caroline Ford, and is used under the Creative Commons license. The
Crickets At Night sound file was created by Mike Koenig, and is used under the
Creative Commons license. The Heart Beat sound file was created by Zarabadeu,
and is used under the Creative Commons license.
Specifications are subject to change without notice. © 2020 VTech
Communications, Inc. All rights reserved. 11/20. VM3262-X_QSG_V1.
Crystal controlled PLL synthesizer
Baby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz
32
2.8″ Color LCD (QVGA 320×240 pixel)
Maximum power allowed by FCC and IC. Actual operating range may vary according
to environmental conditions at the time of use.
Parent unit: 3.7V 2600mAh Li-ion battery Baby unit power adapter: Output: 5V
DC @ 1A Parent unit power adapter: Output: 5V DC @ 1A
Go to www.vtechphones.com to register your product for enhanced warranty
support and the latest VTech product news.
Quick start guide
Technical specifications
Frequency control Transmit frequency Channels LCD Nominal effective range Power requirements
VM3262 VM3262-2
Pan and Tilt
Video Baby Monitor
For more support information
S m
VM3262
VM3262-2
Important safety instructions
The applied nameplate is located at the bottom of the baby unit’s base. When
using your equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a
height
above 2 meters. 4. This product is not a substitute for adult supervision of
the
infant. Supervising the infant is the parent’s or caregiver’s responsibility.
This product could cease operating, and therefore you should not assume it
will continue working properly for any given period of time. Further, this is
not a medical device and should not be used as such. This product is intended
to assist you in supervising your baby. 5. Do not use this product near water.
For example, do not use it next to a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the battery provided. There may be a risk of explosion
if a wrong type of battery is used for the parent unit. The battery cannot be
subjected to high or low extreme temperature and low air pressure at high
altitude during use, storage or transportation. Disposal of battery into fire
or a hot oven, or mechanically crushing or cutting or the battery can result
in an explosion. Leaving the battery in an extremely high temperature
surrounding environment can result in an explosion or the leakage of flammable
liquid of gas. Battery subjected to extremely low air pressure may result in
an explosion or the leakage of flammable liquid or gas. Dispose of used
battery according to the information in The RBRC seal.
7. Use only the adapters included with this product. Incorrect adapter
polarity or voltage can seriously damage the product.
Power adapter information: Parent unit output: 5V DC 1A VTech
Telecommunications Ltd. Model: VT05EUS05100 Baby unit output: 5V DC 1A VTech
Telecommunications Ltd. Model: VT05EUS05100
Rechargeable battery information: Zhu Hai Great Power Energy Ltd. Li-ion
battery, 3.7V 2600mAh Model: ICR18650-2600mAH-3.7V-1S1P 8. The power adapters
are intended to be correctly oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the
socket-outlet shall be installed near the equipment and shall be easily
accessible. 10. Unplug this product from the wall outlet before cleaning. Do
not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not
cut off the power adapters to replace them with other plugs, as this causes a
hazardous situation. 12. Do not allow anything to rest on the power cords. Do
not install this product where the cords may be walked on or crimped. 13. This
product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply in your home,
consult your dealer or local power company. 14. Do not overload wall outlets
or use an extension cord. 15. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces. 16. This product should not be placed
in any area where proper ventilation is not provided. Slots and openings in
the back or bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug. This product should
never be placed near or over a radiator or heat register.
17. Never push objects of any kind into this product through the slots
because they may touch dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
18. To reduce the risk of electric shock, do not disassemble this product,
but take it to an authorized service facility. Opening or removing parts of
the product other than specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause electric shock when
the product is subsequently used.
19. You should test the sound reception every time you turn on the units or
move one of the components.
20. Periodically examine all components for damage. 21. There is a very low
risk of privacy loss when using
certain electronic devices, such as baby monitors, cordless telephones, etc.
To protect your privacy, make sure the product has never been used before
purchase, reset the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor if you will not use it
for some time. 22. Children should be supervised to ensure that they do not
play with the product. 23. The product is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
SAVE THESE INSTRUCTIONS
Cautions 1. Use and store the product at a temperature between
32oF and 104oF. 2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to a heating source. 3.
Batteries should not be exposed to excessive heat such as bright sunshine or
fire.
Warning–Strangulation Hazard–
Children have STRANGLED in cords.
Keep this cord out of the reach of
children (more than 3 ft (0.9m) away). Do
not remove this tag.
5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
· Should keep wireless devices at least six inches from the pacemaker.
· Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.
Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three
feet away from the child at all times. Do not use with an extension cord. Do
not remove this tag.
Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se
trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez
pas de rallonge. Ne retirez pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños.
Este cable debe estar por lo menos tres pies fuera de la alcance del niño en
todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.
What’s in the box
KTeaheurewpseacetyohmifrwrosidtvochenometratehdnihdseoestxutctatohegi.olnfbsderieaoatatnclaclehloatroisftd.mctehhDisrl.oedenrD feooten.netot StranHdga’zéultarRaritaedisnsoqtRgrilunaeeesnmggeoulntdaeción ÉlcopoiirNgc’edenudottseitnlzieds’dcéeueotizintcqpseouraenesfdttartodenone.turdevatleelsrcoeeà,nnagfeeuan.nttNmos.eouirtLnetestietrremozipssp.as Mdlaeodnlcteeolomessnetnninangiuñoaeñnostaioetessrq.etneuxeEsttestceotpaained.seboiclsaóefmfbnuloiueernemraadleaeádnbdtemeelo.lbaeraisNatlcaolacal.rcaoanpNncuoocsreeequite KTeaheurewpseacetyohmifrwrosidtvochenometratehdnihdseoestxutctatohegi.olnfbsderieaoatatnclaclehloatroisftd.mctehhDisrl.oedenrD feooten.netot StranHdga’zéultarRaritaedisnsoqtRgrilunaeeesnmggeoulntdaeción ÉlcopoiirNgc’edenudottseitnlzieds’dcéeueotizintcqpseouraenesfdttartodneone.turdevatleelsrcoeeà,nnagfeeuan.nttmNos.eouirtLnetestietrremozipssp.as Mdlaeodnlcteeolomessnetnninangiuñoaeñnostaioetessrq.etneuxeEsttescteotpaained.seboiclsaóefmfbnuloiueernemraadleaeádnbdtemeelo.lbaeraisNatlcaolacal.rcaoanpNncuoocsreeequite
Quick start guide
x 2
x 2
1 set for VM3262 2 sets for VM3262-2
1 Connect the baby monitor
NOTES
· The rechargeable battery in the parent unit is built-in. · Use only the
power adapters supplied with this product. · Make sure the baby monitor is not
connected to a switch-controlled electric outlet. · Connect the power adapters
in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any
ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not
properly connect to the outlets. · Make sure the parent unit, the baby units
and the power adapter cords are out of reach of children.
Strangulation Hazard
Keep this cord out of reach of children. The cord needs to be at least three
feet away from the child at all times. Do not use with an extension cord. Do
not remove this tag.
Risque d’étranglement
Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez
pas cette étiquette.
Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños.
Este cable debe estar por lo menos tres pies fuera de la alcance del niño en
todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.
Basic operation – Parent unit
Use the menu
Press MENU to enter the menu, or save a setting. You can use the parent unit
for advanced settings or operations, such as to play or stop the baby unit’s
lullaby, or to adjust the baby unit’s sound sensitivity.
While in the menu:
· Press or to scroll among the menu options.
· Press SELECT or to enter the desired submenu.
· Press or to select an item.
Submenu Main menu
· Press SELECT to confirm your selection.
· Press TALK/EXIT or to exit the submenu.
Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted
to the baby unit. Release TALK when finish talking and hear your baby again.
Turn off the screen
Press POWER/LCD OFF to switch off the screen. You can still hear sound from
the selected baby unit.
Press and hold
Tip
· Press any keys on the parent unit to turn on the screen again.
Adjust parent unit speaker volume
1. Press MENU/SELECT when in idle mode.
2. Press or to choose , then press MENU/SELECT to open the submenu.
3. Press or to select desired volume level, then press MENU/SELECT to confirm
your selection.
Zoom
1. Press MENU/SELECT when in idle mode.
2. Press or to choose , then press MENU/SELECT to open the submenu.
3. Press or to choose (Zoom in) or
(Zoom out), then press MENU/SELECT to confirm your selection.
Overview – Baby unit
1
7 10
2
8
3 11
4
5
9
6
Overview – Parent unit
1 2
3
4
9
5
6
7 8
1 Battery LED light
5 LINK LED light
2 3-level sound indicator light 6 TALK/EXIT
3 Arrow Keys
7 POWER/LCD OFF
4 MENU/SELECT
8 Microphone
10 11
9 Power jack 10 RESET 11 Speaker
1 Light sensor
2 Camera
3 Infrared LEDs
4 Microphone
5 POWER LED light
6
ON/OFF switch
7 Speaker 8 Antenna 9 Power jack 10 Slots for wall mounting 11 PAIR/RESET key
Need help?
For operations and guides to help you use your video monitor,
and for the latest information and support, check out our online
S
help topics and online FAQs.
m
Use your smartphone or mobile device to access our online help.
· Go to https://help.vtechphones.com/vm3262 or
https://help.vtechphones.com/vm3262-2; OR
· Scan the QR code on the right. Launch the camera app or QR code scanner app
on your smartphone or tablet. Hold the device’s camera up to the QR code and
frame it. Tap the notification to be redirected to the online help page.
– If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.
You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.
VM3262 VM3262-2
2 Power on or off the baby monitor
Slide the ON/OFF switch to power on or off your baby unit.
3 Positioning the baby monitor
Caution
· Keep the baby unit out of the reach of your baby. Never place or mount the
baby unit inside the baby’s crib or playpen.
Press and hold POWER to power on or off your parent unit.
Press and hold
Press and hold
Power on Power off
3ft (1m)
Caution
· The default volume of your parent unit is level 3, and the maximum volume is
level 5. If you experience high-pitched screeching noise from your baby
monitor while positioning: – Make sure your baby unit and parent unit are more
than 3 feet (1 meter) apart, OR – Turn down the volume of your parent unit.
< 3ft (1m)
Note
· To avoid interference from other electronic devices, place your baby monitor
at least 3 feet (1 meter) away from devices such as wireless routers,
microwaves, cell phones and computers.
4 Status check
Once you power on both your baby unit and parent unit, your parent unit
displays image from the baby unit, and the LINK LED light turns on.
The POWER LED light of baby unit turns on.
Parent unit icons
Status icons
Connection status · or displays when strong signal strength is detected
between the baby
unit and the parent unit. · or displays when moderate or low signal strength
is detected between
the baby unit and the parent unit.
Patrol mode · Displays when the parent unit is in PATROL mode. · For VM3254-2
only
or Current view status · Displays the baby unit number of the baby unit that
is being viewed.
Zoom · Displays when the current image on the parent unit has zoomed in.
Night vision · Displays when the baby unit being viewed has activated the
night vision
feature.
Talkback · Displays when talking back to the baby units from parent unit.
Lullaby · Displays when a lullaby is playing.
Mute alert · Displays when the parent unit speaker volume is set to zero.
· Displays when the parent unit is talking to the baby unit.
or
Real-time temperature · Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)
or Celsius (oC) (e.g. 57 oF or 14 oC).
Battery status
·
animates when the battery is charging.
· displays solid when the battery is fully charged.
· displays when the battery is low and needs charging.
Main menu icons
Main Sub-menu menu
Main Sub-menu menu
Volume Settings
Sound Detection
Parent unit speaker volume
VOX (Voice Activated Alert)
· Adjust the parent unit’s speaker
Sensitivity
volume.
· You can choose to hear sounds from the baby
unit all the time, or to only
hear sounds that exceed
a certain level. Adjust the
Screen off timer
microphone sensitivity of
· The parent unit display will dim to conserve energy after your chosen amount
of time of inactivity.
Brightness · Adjust the parent unit’s LCD
screen brightness level.
your baby unit, the higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. See Sound sensitivity and sound activation section.
Temperature
Zoom · Zoom in and out of the video
displayed from the baby unit
· Turn on/off temperature alert tone.
· Set the parent unit to beep whenever the room temperature detected by the
baby unit falls outside of the set temperature range.
· Set the minimum/maximum temperature.
· Set temperature display in Fahrenheit (oF) or Celsius (oC)
Sound-activated screen · When it is on, and the baby
unit detects no sound, the parent unit screen stays off to save power. Once a
sound is detected, the parent unit screen and speaker turns on automatically,
and you can see and hear your baby. The parent unit will then turn off again
after 50 seconds of no sound detection.
Note · When the parent unit screen
is off and it receives alerts, for example, link lost between parent unit and
baby unit, or battery is low, the parent unit screen and speaker will turn on
for 10 seconds.
Parent unit icons (cont’d)
Main menu icons
Main Sub-menu menu
Lullaby Lullaby volume · Adjust the baby unit’s speaker volume when playing
the lullaby.
Warning icons and messages
The battery is empty and Battery low at needs to be recharged. Parent Unit
Operation is in progress.
· Select one of the 4 melodies to play or stop a lullaby
Temperature too high
The temperature detected by the baby unit is higher than the desired temperature alert range.
Monitoring Mode (For VM3262-2 only) Patrol mode · Monitor your baby in PATROL
mode, where the screen will cycle through display videos streamed from all the
linked baby unit cameras · For VM3262-2 only
· View the video from your selected paired baby unit’s camera.
Temperature too low
The temperature detected by the baby unit is lower than the desired temperature alert range.
No Link to Camera
The parent unit is searching for baby units or the link between the baby unit and the parent unit is lost.
The parent unit is connected to AC power.
Parent Unit Indication Lights
LINK
· On when the parent unit is linked to the baby unit.
· Flashes when the link to the baby unit being viewed is lost.
· On when the parent unit is connected to AC power, or the battery is
charging.
· Flashes when the parent unit battery is low and needs charging.
· Off when the parent unit is disconnected from AC power.
Sound sensitivity and sound activation
Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear
sounds that exceed a certain level. You can use the parent unit to adjust the
microphone sensitivity of your baby unit. The higher the sensitivity level,
the more sensitive the baby unit is in detecting sounds for transmitting to
the parent unit. The VOX sensitivity level is preset to the highest level.
VOX Sensitivity level
Description
Highest
The parent unit speaker is constantly on, and you will hear all sounds
(including background noises) from your baby’s room.
High
The parent unit speaker turns on for soft babbling and louder sounds from your
baby. It remains quiet when your baby sleeps soundly.
Medium
The parent unit speaker turns on for loud babbling and louder sounds from your
baby. It remains quiet when your baby makes soft sounds.
Low
The parent unit speaker turns on for crying and louder sounds from your baby.
It remains quiet when your baby makes soft sounds.
Lowest
The parent unit speaker turns on for loud crying or screeching sounds from
your baby. It remains quiet when your baby makes soft sounds.
Sound activated screen
When sound activation is on, the parent unit screen stays off to save power
when the baby unit detects no sound. Once the baby unit detects sounds that
are louder than the chosen sound sensitivity level, the parent unit screen
turns on automatically. It will then turn off again after 50 seconds of no
sound detection.
Dim mode
The dim mode is to help you save the parent unit power. Your parent unit
display will dim automatically after 10 minutes of inactivity, in which there
is neither key pressed nor alert received from the baby unit.
10 min inactivity
Press any buttons
Note
· While the screen is dimmed, any keypress or alert message will trigger the
screen to return to the preset brightness level. After 10 minutes of
inactivity, it will resume to dim mode.
Night vision
The baby unit has infrared LEDs that allow you to see your baby clearly at
night or in a dark room. When the baby unit being viewed detects low light
levels, the infrared LEDs are switched on automatically. The images from the
baby unit are in black and white, and appears on the screen.
Notes
· It is normal to see a short white glare on your parent unit screen as the
baby unit is adapting to the dark environment.
· When the infrared LEDs are on, the images are in black and white. This is
normal.
Tip
· Depending on the surroundings and other interfering factors, like lighting,
objects, colors and backgrounds, the display resolution may vary. Adjust the
baby unit’s angle or place the baby unit at a higher level to prevent glare
and blurry display.
For VM3256-2 only
Status check – Two baby units
If you are viewing baby unit , the POWER LED light of baby unit As baby unit
is not being viewed, its POWER LED light flashes.
turns on.
Note
· If you power on only one baby unit, your parent unit may display and the
LINK LED light will flash.
Change different views – Patrol
1. Press MENU when the parent unit is idle 2. Press or to choose , then press
SELECT or . 3. Press or to choose , then press SELECT to confirm your
selection.
10s
Change different views – Single-cam
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press SELECT or .
3. Press or to choose between you would like to view.
, then press SELECT to confirm the camera unit
Mount the baby unit on dry wall (optional)
Notes
· Check for reception strength and camera angle before drilling the holes.
· The types of screws and anchors you need depend on the composition of the
wall. You may need to purchase the screws and anchors separately to mount your
camera units.
Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole.
Note
· Check for reception strength and camera angle before drilling the holes.
Place the wall mount bracket on a wall and then use a pencil to mark two holes
in parallel.
Drill two holes in the wall ( 7/23 inch drill bit ). If you drill the holes
into a stud, go to step 3.
-OR-
If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the wall
anchors are flush with the wall.
Place the camera unit on the wall mount bracket, and then slide it forward until it locks into place. Connect the power adapter to the camera unit and a power supply not controlled by a wall switch.
Frequently asked questions
Below are the questions most frequently asked about the baby monitor.
Why does the baby monitor not respond normally?
Why don’t the power-on light of the baby unit and parent unit go on when I
switch on the units?
Try the following (in the order listed) for common cure: 1. Disconnect the
power to the baby units and the parent unit. 2. Wait a few seconds before
connecting power back to the baby units and the parent unit. 3. Turn on the
baby units and the parent unit. 4. Wait for the parent unit to synchronize
with the baby units. Allow up to one minute
for this to take place.
Perhaps the parent unit is not connected to the power. Insert the appliance
plug into the parent unit and put the adapter in a wall socket. Then, press
and hold POWER to switch on the parent unit and to establish connection with
the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug
into the baby unit and put the adapter in a wall socket. Then, slide the
ON/OFF switch to ON to switch on the baby unit and to establish connection
with the parent unit.
Why doesn’t my parent Make sure the power is not controlled by a wall switch.
unit charge while connected to AC power?
You may have used the battery for a long time. See Warranty for repair/replacement.
Why is my screen in black and white?
The screen is in black and white during night-time or in a dark room when the night vision feature is activated. This is normal.
Why do I get glare or blurry display on my screen when viewing my baby at night?
During night-time or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.
Why does the baby monitor produce a high-pitched noise?
Why does the parent unit beep?
The parent unit and baby units may be too close to each other. · Move the
parent unit away from the baby units until the noise stops; OR · Turn down the
volume of your parent unit.
The baby units may be out of range. Move the parent unit closer to the baby
units (but not less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform
normally. Charge the battery in the parent unit until the battery icon becomes
solid .
The temperature of your baby’s room may be too high or too low.
Why does the parent unit react too quickly to other sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a sound/Why can’t I hear my baby cry?
Why can’t I establish a connection? Why is the connection lost every now and
then? Why are there sound interruptions?
The parent unit speaker volume may be too low. See Adjust speaker volume to
increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity
of the baby unit to set to a higher level.
The baby units may be out of range. Move the parent unit closer to the baby
units (but not less than 3 feet).
Other electronic products and wireless products may cause interference with
your baby monitor. Try installing your baby monitor as far away from these
devices as possible.
If you power on only one baby unit, your parent unit may display , and the LINK LED light will flash.
The RBRC seal
The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc.
is voluntarily participating in an industry program to collect and recycle
these batteries at the end of their useful lives, when taken out of service
within the United States and Canada. The program provides a convenient
alternative to placing used Li-ion batteries into the trash or municipal
waste, which may be illegal in your area. VTech’s participation makes it easy
for you to drop off the spent battery at local retailers participating in the
program or at authorized VTech product service centers. Please call 1 (800) 8
BATTERY® for information on Li-ion battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in this program is part of
its commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of
Call2recycle, Inc.
FCC and IC regulations
FCC Part 15 This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements are intended to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: · Reorient or relocate the receiving antenna. · Increase
the separation between the equipment and receiver. · Connect the equipment
into an outlet on a circuit different from that to which the receiver is
connected. · Consult the dealer or an experienced radio/TV technician for
help. WARNING: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This device complies with Part 15 of the
FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed by a user or
bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The baby unit shall be
installed and used such that parts of all persons’ body are maintained at a
distance of approximately 8 in (20 cm) or more. The transmitter and antenna of
the parent unit shall be held at least 1 in (2.5 cm) from your face. This
Class B digital apparatus complies with Canadian requirement: CAN ICES-3
(B)/NMB-3(B)
Industry Canada This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of the
device. The term ’IC:’ before the certification/registration number only
signifies that the Industry Canada technical specifications were met. This
product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
RF radiation exposure statement The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. The baby unit
should be installed and operated with a minimum distance of 8 in (20 cm)
between the baby unit and all persons’ body. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. This equipment complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for
energy consumption. Your baby monitor is set up to comply with the energy-
conserving standards right out of the box. Follow the instructions to install
and charge the battery. The CEC battery charging testing mode is activated
while charging. Even if the parent unit is paired to baby units, the CEC
battery charging testing mode is activated while it is powered off and
charging.
For cETL compliance only
Mesures de sécurité importantes La plaque signalétique appliquée est située au
bas du socle de l’unité du bébé. Lorsque vous utilisez votre appareil, vous
devriez toujours suivre certaines mesures de précaution de base afin de
réduire les risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent : 1. Observez toutes les instructions et mises en garde
inscrites
sur l’appareil. 2. L’installation par un adulte est requise. 3. MISE EN GARDE:
N’installez pas l’unité du bébé à une
hauteur supérieure à 2 mètres. 4. Ce produit ne remplace pas la surveillance
adulte du
nourrisson. La supervision du nourrisson est la responsabilité du parent ou de
la personne qui s’occupe de l’enfant. Ce produit pourrait cesser de
fonctionner et, par conséquent, vous ne devriez pas présumer qu’il continuera
de fonctionner correctement pendant une période de temps donnée. De plus, il
ne s’agit pas d’un instrument médical et ne devrait pas être utilisé comme
tel. Ce produit est destiné à vous aider à superviser votre bébé. 5.
N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité,
par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un
sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque
d’explosion si un autre type de batterie est utilisé pour l’unité Parents.
N’incinérez pas les piles. Cellesci risqueraient d’exploser. Jetez les piles
usées selon les renseignements suivant le sceau du RBRC. 7. N’utilisez que les
adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques : Adaptateur de l’unité du parent
: Sortie : 5V DC 1A VTech Telecommunications Ltd. Modèle : VT05EUS05100
Adaptateur de l’unité du bébé : Sortie : 5V DC 1A VTech Telecommunications
Ltd. Modèle : VT05EUS05100
Informations sur les piles rechargeables : Zhu Hai Great Power Energy Ltd. Li-
ion battery, 3.7V 2600mAh Model: ICR18650-2600mAH-3.7V-1S1P 8. Lorsqu’ils sont
branchés dans une prise de courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la verticale ou au plancher. Les
broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation
et le maintenir en place si celuici est branché dans une prise au plafond,
sous une table ou dans un meuble. 9. Pour les PRODUITS À BRANCHER À UNE PRISE
DE COURANT, la prise de courant doit être installée près du produit, afin
d’assurer une accessibilité sécuritaire à la prise de courant. 10. Débranchez
ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez
pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car
ceci peut présenter un danger potentiel. 12. Ne laissez aucun objet reposer ni
appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un
endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué
sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous
possédez à votre domicile, consultez votre marchand ou votre compagnie locale
d’électricité. 14. Ne surchargez pas les prises de courant murales ni les
rallonges électriques. 15. Ne placez pas cet appareil sur un chariot, meuble,
trépied, support de montage ni table chancelants. 16. Les trous et ouvertures
du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer
l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces
ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant
sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un
calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous
assurer qu’il y ait une bonne circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car
ils pourraient entrer en contact avec des points de tension dangereux ou
causer des courtscircuits qui peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide dans ce produit.
18. Afin de réduire les risques d’électrocution, ne démontez pas cet
appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du
boîtier ou le retrait de toutes pièces que contient cet appareil, à
l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de
vous exposer à des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez l’appareil
en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées.
21. Il existe un très faible risque de perte de confidentialité avec certains
appareils électroniques (autres écoute-bébés, téléphones sans fils etc.). Pour
l’éviter, s’assurer que le produit n’a jamais été utilisé avant l’achat,
réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé quand il
n’est pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer qu’ils ne
jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant
des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui
manquent d’expérience et de connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité. CONSERVEZ CES
INSTRUCTIONS
Mises en garde 1. Utilisez et entreposez le produit à une température entre
0° C (32°F) et 40°C (104° F). 2. N’exposez pas cet appareil à des froids ou
des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près
d’une source de chauffage. 3. Le bloc-piles ne doit pas être exposé à la
chaleur excessive telle que la lumière du soleil ou au feu.
Avertissement – Risque de strangulation
– Les enfants se sont ÉTRANGLÉS dans des
cordons. Gardez ce cordon hors de portée
des enfants (à plus de 0,9 m). N’enlevez pas
cette étiquette.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :
L’organisme `Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
· Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.
· Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF) Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.
Limited warranty
What does this limited warranty cover? The manufacturer of this VTech Product
warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that
the Product and all accessories provided in the sales package (“Product”) are
free from defects in material and workmanship, pursuant to the following terms
and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective
Product”)? During the limited warranty period, VTech’s authorized service
representative will repair or replace at VTech’s option, without charge, a
Materially Defective Product. If we repair the Product, we may use new or
refurbished replacement parts. If we choose to replace the Product, we may
replace it with a new or refurbished Product of the same or similar design. We
will retain defective parts, modules, or equipment. Repair or replacement of
the Product, at VTech’s option, is your exclusive remedy. VTech will return
the repaired or replacement Products to you in working condition. You should
expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period? The limited warranty period for the
Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the date the repaired or
replacement Product is shipped to you or (b) the time remaining on the
original one-year warranty; whichever is longer.
What is not covered by this limited warranty? This limited warranty does not
cover: 1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation, abnormal operation
or handling, neglect, inundation, fire, water or other liquid intrusion; or 2.
Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech; or 3. Product
to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems; or 4. Product to the extent
that the problem is caused by use with non-VTech accessories; or 5. Product
whose warranty/quality stickers, product serial number plates or electronic
serial numbers have been removed, altered or rendered illegible; or 6. Product
purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes); or 7.
Product returned without a valid proof of purchase (see item 2 below); or 8.
Charges for installation or set up, adjustment of customer controls, and
installation or repair of systems outside the unit.
How do you get warranty service? To obtain warranty service in the USA, please
visit our website at www.vtechphones.com or call 1
800-595-9511. In Canada, go to
www.vtechcanada.com or call 1
800-267-7377. NOTE: Before calling for
service, please review the user’s manual – a check of the Product’s controls
and features may save you a service call. Except as provided by applicable
law, you assume the risk of loss or damage during transit and transportation
and are responsible for delivery or handling charges incurred in the transport
of the Product(s) to the service location. VTech will return repaired or
replaced Product under this limited warranty. Transportation, delivery or
handling charges are prepaid. VTech assumes no risk for damage or loss of the
Product in transit. If the Product failure is not covered by this limited
warranty, or proof of purchase does not meet the terms of this limited
warranty, VTech will notify you and will request that you authorize the cost
of repair prior to any further repair activity. You must pay for the cost of
repair and return shipping costs for the repair of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty service? 1. Return the
entire original package and contents including
the Product to the VTech service location along with a description of the
malfunction or difficulty; and 2. Include a “valid proof of purchase” (sales
receipt) identifying the Product purchased (Product model) and the date of
purchase or receipt; and 3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or oral communications
related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding
the Product. There are no other express warranties. No one is authorized to
make modifications to this limited warranty and you should not rely on any
such modification. State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other rights, which vary from
state to state or province to province. Limitations: Implied warranties,
including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to
one year from the date of purchase. Some states/ provinces do not allow
limitations on how long an implied warranty lasts, so the above limitation may
not apply to you. In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including, but not limited to
lost profits or revenue, inability to use the Product or other associated
equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any
damage or loss resulting from the use of this user’s manual. VTech
Communications, Inc. and its suppliers assume no responsibility for any loss
or claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road –
Ste 555 Tigard, OR 97223, United States Phone: 1
800-595-9511 in the U.S. or 1
800-267-7377 in Canada
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>