global sources IC-M1 15W Magnetic Wireless Car Charger User Manual
- June 6, 2024
- global sources
Table of Contents
User Manual
Magnetic Wireless Car Charger
Product Features
- Top backside touch button, touch to open and easy for one-hand operation. Charging indicator on both sides, anti-slip silicone rubber in the middle.
- Built-in magnet and wireless charging transmitter coil, the magnet phone will automatically find the right coil position to start wireless charging, and the two clamps will automatically hold the phone.
- Anti-slip silicone on both clamps, Type-C charging port.
- Built-in stepper motor, it works with low noise.
- NPO capacitors, lower charging temperature, and high charging efficiency.
- Standby mode: the green and blue LED indicator light flashes alternatively, then the green indicator light keeps on.
- Charging mode: the blue LED indicator light keeps on, the light turns to green if remove the receiver.
- FOD function: when putting metal or magnet objects on the charger, the blue and green LED indicator light will flash for reminding.
- Perfect protective function based on over-voltage, over-current, over-temperature, and short-circuit protection.
Specifications
| Input | DC 12V/1.5A,9V/1.67A,5V/2A |
|---|---|
| Output | 15W/10W/7.5W/5W |
| Product Standard | Qi |
| Charging Distance | ≤ 10mm |
| Charging Efficiency | ≤ 80% |
| Product Dimension | Φ72.5∗66.9∗93mm |
| Product Material | ABS+Silicone |
※ Fast wireless charging requires QC2.0/3.0 quick car charger.
Product Parts Description
Product Operating Guide
- Please make sure the product connects to the power before using it.
- The green LED indicator lights is on if connected with power.
- The LED indicator light will flash and the product stop charging when the current is too large or there is a foreign object. Do not wirelessly charge the phone if a similar situation happened.
- Please touch the backside power button to open the two arms, the wireless charging start and the two arms will close automatically once you put the phone on the charger. Only need to touch the power button again to release two arms and easily remove the phone.
- Please purchase the wireless receiver module or case separately (Not included in the product) if your phone does not support wireless charging.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is powered on, to avoid short circuit or leakage.
- Please do not use it in severely high temperatures, high humidity, or corrosive environment, to avoid damage to the circuit leakage.
- Please do not put the magnetic stripe or chip card (Such as an ID card, bank card, etc.)on the charging pad to avoid causing the magnetic card to lose efficacy.
- Please do not put the metal (Such as coins etc.) on the charging pad when charging, to avoid damage from heating.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>