ARTISTE DGH600 2.4GHz Digital Wireless Professional Gaming Headphone User Manual

June 6, 2024
ARTISTE

ARTISTE
DGH600 2.4GHz Digital Wireless Professional Gaming Headphone
User Manual

FEATURES

  1. 2.4GHz Digital Hopping System Terminology
  2. Immersive In-game Experience Virtual Surround Sound
  3. FIrdble Noise Cancelling Microphone
  4. Comfortable wearing for marathon gaming MID
  5. Direct audio line-In
  6. Power Saving Mode
  7. Undetectable low latency as a wired headset

What’ sin the box

CONNECTION

Microphone

PC

If there’s no sound on the headset, please change the audio settings on the PC:
On the Windows Taskbar, right-click the Speaker Icon, Select Playback Devices. a. Set a 2.4G Gaming headset as your default device. b. Select Recording Devices, Set 2.4G Gaming headset as your default device.

PS4

PM console setting

  1. From the PS4 main menu, go to Settings> Devices > Audio Devices
  2. Set Input Device to USB Headset (2.4G Gaming headset)
  3. Set Output Device to USB Headset (2.4G Gaming headset)
  4. Set Output to Headphones to All Audio 5. Set Volume Control (Headphones) to 100% volume.

Use 3.5mm-3.5mm audio cable(4 poles) to connect the headphone and the 3.5mm port of the controller(adapter not included) of Xbox One S/X. (Note: when using 3.5mm audio cable to connect with the headphone, the headphone is switched to a wired headset, the function keys on headphone are disabled.)
Audio output setting for Xbox One S/X:

  1. Select “setting’ on the menu page and press Yes
  2. Select “display and sound” and press Yes;
  3. Select “chat console” and press Yes;
  4. Enter the “chat console” volume selection menu;
  5. Select “no change” and press Yes;

You may set the USB audio volume on Switch to maximum by using the volume buttons on the Switch console, then adjust the volume with the headset volume wheel.

NOTE: Please ensure the firmware of your Nintendo Switch is updated to 4.0.0 or above.

VOLUME WHERE

Headphone beeps in maximum or minimum.
To protect your hearing, please do not use headphones at high volume for a long time.

Microphone I Surround sound
When the headphone is powered on, the microphone is on, and the surround sound switch is off by default.
Press   to turn on/off the microphone, one beep is on, and two beeps are off.
Press and hold for 4 seconds to turn on/off virtual Surround Sound, one beep is off, two beeps is on.
Intelligence power-saving
When the headphone is on, if the transmitter is not connected to any device or there is no audio signal input, the headphone will enter power saving mode after 5 minutes. You need to turn off the power and then turn it on to use headphones again.
Low-power warning
When the battery is running out, you will hear a beep every five minutes for a warning. Please charge the battery as soon as possible or use a 3.5mm cable to connect with headphones and audio devices.
Direct line-in as a wired headphone
Use a 3.5mm cable to connect with the headphone and audio device, it is switched to a wired headphone. All function keys on headphones and Surround Sound is disabled. The microphone will keep open.

Re-pair
Note: This is a factory-paired SET, there’s No Need to pair them; just tum them on and they will auto-connect! If they can’t reconnect, please follow the below steps to reconnect them.

  1. Turn on the headphone.
  2. Press and hold   for more than 10 seconds then hear a short beep sound like a signal interrupted.
  3. If still hear no sound, just turn off the headphones and then tum on it again. Head-phone and transmitters will be connected.

LED INDICATOR

Model Status LED
DGH600 Power ON Solid blue
Power OFF Blue and green LED OFF
Re-pair Green LED flashing
Pair successfully with the audio source Solid green
pair successfully without an audio source Green LED flashing
without audio source after 5 minutes Green LED OFF
Battery is low Red LED flashing
Charging Solid red
Fully charged Solid green

TROUBLESHOOTING

No Sound

Possible cause Solution
Power is off Confirm that the headphone is on. The blue LED on the headphones

is solid.
Dead/low battery| Confirm that the headphone battery is charged.
Loose connection| In PC or game console use, confirm that the USB transmitter is properly seated in the USB port of the device.
In wired use, confirm that the audio cable plugs are firmly seated in the headphone and the audio device.
Lost pairing| Confirm that the connection green LED on the headphones
stays on. If the LED is slowly flashing indicates that the transmitter isn’t communicating with the headphone. Please follow the re-pair steps.

Audio Drops, Popping or Clicking Sounds

Possible cause Solution
For best performance, stand within 30 feet from the transmitter.
Confirm that there is no wall or other large object
Poor transmission between the headphone and transmitter. Confirm that the

location of the transmitter is clear of obstructions and isolated from Wi-Fi base stations or other potential sources of interference.

Voice Chat Drops

Possible cause Solution
Incorrect PC/console-setup Confirm that the PC or game console is properly

configured for the 2.4G Gaming headset. See PC and console setup above.
Mic muted| Press on the headphone to switch the microphone between on and off (muted).
Mic disconnected| Confirm that the jack of the removable microphone is firmly inserted into the headphone.

TECHNICAL SPECIFICATIONS

Transmission Mode:2.4GHz Distortion:0.5%
Working Range:15 meters Battery:3.7V Lithium Battery
Output Power:30mW Battery Capacity:1000mAh
Frequency Response:20Hz-20KHz Charge Time:3 hours
Sensitivity:109dB Working Time:25 hours
Impedance:320 Port:Type-C 3.5mm
Driver Unit:40mm Color:Black and red

S/N Ratio:75dB

CAUTION

To protect your hearing, please do not use headphones at high volume for a long time. The wireless transmission will produce an electromagnetic signal which may interfere with the heart pacemaker or other medical instruments’ properly functioning. Please follow your doctor s instructions
. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with FCC’s radiation exposure limits set forth for an uncontrolled environment.
Work temperature:-10°C-45t:
– CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
– No naked flame sources, such as lighted candles, should be placed on the apparatus.
– Attention should be drawn to environmental aspects of battery disposal.
– The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
– WARNING: Please refer to the information on the exterior bottom enclosure for electrical and safety information before operating the apparatus.
Use only power supplies listed in the user instructions. Adapter model: YLJXA-E050055 or YLJXA-U050055 or YLJXC-050055 Made By: Dongguan Yinli Electronics Co., Ltd
**** Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.”This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals