Shenzhen Rango Innovation Technology S3 OXS Soundbar User Manual

Shenzhen Rango Innovation Technology S3 OXS Soundbar User Manual

Before using the sound bar, please read the following important

notifications.

• For future reference, please read the guidance manual thoroughly and keep it preserved.

• Please change your Audio Output Settings into the PCM form. For more information, please check the guidance manual of the playing device.

• To preserve better sound quality, please set the volume of the sound bar to 75% of the maximum volume (Note: 3 levels reduced from the maximum will be 75%).
  Meanwhile, please adjust the volume of the playing device to the proper level.

• To preserve better audio sound quality, please press the button of Movie, Music, or News to choose the proper equalizer mode.

• The recommended equalizer made is as follows:

• The selected mode and volume setting will remain in the system, 50% of the maximum volume is also included.

• The audio output can be infected by the setting of the playing device. If necessary, please adjust the settings of the playing device to improve the sound quality.

• Not every function on the remote controller can be found on the sound bar. Please keep well of the remote controller

• Disconnect the power adapter from the socket to shut down the sound bar completely.

• Do not modify the system without authorization, otherwise, it may cause safety issues, legislation, as well as the invalidation of your warranty.

This lightning pattern with an arrow symbol in the triangle warns the user of an uninsulated dangerous voltage in the system enclosure, which may be sufficient to constitute an electric shock hazard.

The exclamation mark in the triangle, as marked in the system, is intended to remind users that there are important operation and maintenance instructions in this guidance manual.

Do not modify the system without authorization, otherwise, it may cause safety issues, legislation, as well as the invalidation of your warranty.
The system contains magnetic materials. If you have any questions about whether it may affect the operation of implantable medical devices, please contact your doctor.
Do not place open flame sources on or near the system, such as lighted candles.

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Package List

• OXS Sound Bar x 1
• Accessories:
• power adapter x 1
• Manual x 1
• Remote control x 1
• Optical cable x 1
• Coaxial line x 1
• Wall brackets x 2
• Expansion tubes x 2
• Screws M4 x 30mm x 2
  Note: The attachments are subject to change without notice.

Features

• Total power of 40 watts
• 32-inch bar sound
• 2.0 channels
• 4 2-inch speakers, 2 sound guide tubes
• Analog audio interface (AUX input)
• Digital audio interface (optical input and coaxial input)
• Streaming music from smartphones or tablets
• The sound bar can be installed on the wall
• Full-function infrared remote control
• Digital control audio processing sound mode
• Three sound effect modes
• Strong and abundant bass effect

Specifications

Power Adapter

Input: 100V~240V/AC 50~60Hz
Output: 22VDC 1.8A
Protection   Class: Il
Function Class: VI
Remote Controller: 1.5V

Speaker

Output: 20watts x2
Frequency response: 60Hz~20kHz
Signal to noise ratio: 80dB (A-weighting)
Distortion: -70dB (A-weighting)
Standby power consumption: <0.5watts

Button Introductions

1. Volume down

2. Volume up

3. Power switch(stand by mode)

4. Sound mode

5. Media sources
   Port Introductions
   

6. COAX

7. Optical

8. USB

9. AUX

10. DC IN 22V 1.8A

Indicator Light Instructions

1. Volume down
   The indicator light flashes briefly when pressed, and the indicator light is always on when the volume is reduced to the minimum.

2. Volume up
   The indicator light flashes briefly when pressed, and the indicator light is always on when the volume is increased to the maximum.

3. Power
   Turn on the sound bar (The light is white at this point) or switch it to standby mode (The light will turn orange at this point)

4. Switch sound mode
   Mode| Light Color
   ---|---
   Music| Yellow
   News| Green
   Movie| Purple

5. Switch media sources
   **** Port| Light Color
   ---|---
   OPT| Yellow
   COAX| White
   AUX| Green
   BT| Blue
   USB| Purple

Remote Controller

Unpacking

• Remove all packaging.

• Check for the presence of all parts and for transport damage.
  In case of damage or incomplete delivery, please contact your dealer.

• Please keep the packaging. The system can be stored in it, if not used for a longer period of time.

Preparation before installation

The Sound bar system serves as an audio output device and features wireless and wired connections. You can place the sound bar on a horizontal surface or mount it on a wall. When mounting it on a wall, pay attention to the following:

• The supplied wall mount brackets, wall anchors and screws can be used to fix the sound bar to a wall. The wall mount brackets are designed for vertical walls constructed of solid concrete, bricks or wooden.
• When installing on a cinder block wall, first verify that the blocks have a minimum of 1.2 inch (3cm) of actual concrete wall thickness to be used for the wall anchors.
• If you are uncertain about the construction of your wall, please consult a qualified contractor or installer for assistance.
• Ensure that the wall anchors and screws you use are stronger enough to support the weight of the sound bar and long enough to sufficiently grip the wall.
• It is strongly recommended to use the supplied wall anchors and screws.
• Additional tools (not included) are required for the installation.
• Do not over tighten screws.
• Use an electronic stud finder to check the wall type before drilling and mounting
• During mounting, keep away children and pets.
• Make sure the sound bar is mounted in reach of a wall outlet.

Caution!

When placing the sound bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2 inches (5cm) of space around the sound bar for ventilation. If the sound bar is enclosed in a tight space, without ventilation, heat generated from the sound bar could produce a potential heat hazard.

• Make sure the power adapter is disconnected from the electrical outlet before making any mounting and connection.
• During operation, if the cables require to be reconnected, the power adapter must be disconnected first, otherwise damage to the system may result.

Wall mounting

1. The distance between the two wall brackets is 777mm (30.59 inches).
2.  Mark the drilling location and drill 2 holes in the wall.
3. Insert 2 wall anchors into the holes, using a hammer if necessary.
4. Use 2 screws to install on the wall and fix the screws.
   

Optical and Coaxial Cable Connection

• Use the provided optical or coaxial cable to connect the sound bar to a TV, DVD, Blu-ray player or other suitable equipment.
• Connect to the optical or coaxial output of a TV, DVD, Blu-ray player, set-top box, or other suitable equipment sockets.
• Connect the other end to the optical or coaxial input socket of the sound bar.
  

Audio Cable Connection USB Connection

Use the USB interface and USB device connector of this product, as shown in the figure below, Listen to the audio program stored on the USB device through the sound bar.

Note:

1. Requirements for USB devices FAT16 or FAT32 file format, use Type-A interface, follow USB2.0 specification: WAV, WMA, MP3.
2. Press the key on the remote control or the sound bar to switch the product to USB mode (the source indicator is flashing purple).
3. Connect the USB flash drive with audio programs to the sound bar, and the sound source indicator will show a solid purple after the USB flash drive is connected.
4. Play audio programs stored on the USB device through the remote control. During playback, you can use these button on the remote controller to perform playback operations.
5. To exit the USB playback mode, please select another media source.
   

Audio Cable Connection cable Connection

• Use a 3.5mm stereo cable to connect the AUX interface of this product and the AUX interface of MP3 and other devices. All audio equipment with an AUX interface can be connected in this way, such as TVs, computers, etc. As shown below.
• Use a 3.5mm one-to-two stereo cable to connect the AUX interface of this product and the AUDIO OUT L R interface of Blu-ray players, DVD players, set-top boxes, TVs, and other devices, as shown in the figure below.
  

Instructions for the remote control

Install the battery, replace the battery

1. Slide open the battery compartment cover.
2. Insert 2 AAA batteries into the battery box. Match the polarity markings in the battery compartment.
3. Close the battery compartment cover.
   

Warning!

The sound bar can only be used with the included remote control package. It is not compatible with the universal remote control compatible.

• Be sure to insert the battery according to the correct polarity mark.
• Use only high-quality batteries, low-quality batteries may leak and cause damage.
• If you will not use it for a long time, remove the battery from the remote control. If the battery leaks, the remote control may be damaged.

Use Suggestions

• If the remote control does not work properly, replace the battery.
• Make sure there are no obstacles between the remote control and the sound bar.
• If the following conditions occur, the remote control may be less effective:
  1. There is an obstacle between the remote control and the infrared receiver.
  2. Simultaneous operation of other remote controllers.
  3. The battery is low.

Remote control instructions

Remote control working range

Note:

• When there is an obstacle between the remote control sensor of the soundbar and the remote control, the remote control may not operate.
• When direct sunlight, incandescent light, fluorescent light, or any other strong light shines on the bar sound, the operation of the remote control may be unstable.

Warning!

• Not all remote control functions can be found on the sound bar.
  Please keep the remote controller in a safe place.

Connect the Power and Start Enjoying Your Sound Bar

• Before connecting the power adapter, make sure that all source connections are properly connected. Plug the power adapter into the DC IN socket and then into a suitable power socket. The power indicator lights up red indicates that the sound bar is in standby mode.
• Turn off the TV speakers: To avoid hearing distorted sound, turn off the TV speakers. For details, refer to the user manual of the TV.
• Turn on the power of the sound bar: Press the power button on the sound bar or remote control. The power indicator lights up orange
• Check whether the sound comes from the sound bar.

Select Sound Mode

• Digital control audio processing includes three sound modes: Movie, Music, and News. (Note: There is no sound mode indicator on the soundbar)
• To get a better sound effect, please press the Movie, Music, or News button on the remote control to select the appropriate sound mode.
• The recommended sound modes are as follows:

Auto Wakeup & Stand

• If there is no signal of input for 15 minutes after turning the sound bar on, it will automatically enter standby mode.
• If the signal break in at standby mode, the sound bar will automatically recover the media source and sound mode from the last time.

Note:

• Even after the power of the sound bar is turned off, the sound mode selection and volume setting will be saved in the memory, and the volume setting from 50% to the maximum value will be saved to 50%.

• Before turning on the soundbar, set the volume of the source device to a low level.
  Then increase the volume of the source device to a comfortable level.

• Disconnect the power adapter from the power outlet to completely turn off the sound bar.

Basic function description

Select Media Source

You can permanently connect multiple media devices to the sound bar.

The available connection sources are: OPT/COAX/AUX/Bluetooth/USB

You can press the button or the OPT/COAX/BT/AUX button on the remote controller to switch the connection sources. Different sources will corresponds to different light colors (Please check the Page 9 for detailed information).

Basic function description >>> Playback Function

Generally, the playback function can be managed through the controls of the connect-ed source device. Or, use the buttons of the remote control and sound bar.

Even after the sound bar is power off, the volume source and Bluetooth pairing records will be saved in the memory. The audio output of the sound bar is affected by the settings of the connected signal source. If necessary, adjust the signal source settings to improve audio output.

Bluetooth Function Introduction

External Bluetooth devices can be connected to the TV sound bar system via Bluetooth connection.

1. Press the BT (Bluetooth) button on the remote control to enter Bluetooth mode. The Bluetooth indicator lights up blue.
2. Activate the Bluetooth function of the external device and search for Bluetooth devices.
3. Select OXS S3 from the list of Bluetooth devices.
4. Follow the instructions displayed on the device screen.
5. After the Bluetooth connection is established, the files in the connected Bluetooth device will be played through the sound bar.

Disconnect the Bluetooth Device

@ Use the Bluetooth device to disconnect. The sound bar will start searching for
another Bluetooth device.

@ Long press the BT (Bluetooth) button on the remote controller or the M (Mode)
button on the sound bar for about 2 seconds to disconnect the current Bluetooth
device. Long press again for about 2 seconds to reconnect to the current
Bluetooth device.

Note:

• Bluetooth works best within a range of up to 33 feet (10 meters). The music stream may be interrupted by obstacles between the Bluetooth device and the sound bar, such as walls, metal casings covering the device, or operating at the same frequency Other equipment nearby.
• If the connected device is out of Bluetooth range, the system will automatically reconnect when the device returns within range.
• Even after the power of the sound bar is turned off, the current Bluetooth device connection will be saved in the memory.

Select and Play Audio Files or Music on Bluetooth Devices

• During playback, you can use these buttons on the remote controller to perform playback operations.
• During playback, if a call is connected, music playback will be paused.
• If the music transmission is interrupted, move the Bluetooth device closer to the sound bar.
• To exit the Bluetooth mode, select another audio source.
• After switching back to Bluetooth mode, the Bluetooth connection will be restored.

Troubleshooting

• Check whether the power adapter is correctly connected to the power outlet.
• Check if the DC plug is correctly connected to the DC IN socket.
• Unplug the power adapter for at least one minute and then reconnect.

No sound|

• Press the power button on the sound bar or remote control to turn on the sound bar. The power indicator lights up orange.
• Increase the volume of the TV to the maximum.
• Press the mute button on the remote control to restore the sound.
• Ensure that the source device has the correct volume setting and is playing a track.
• Make sure that the correct source device is selected.
• Plug the audio cable into the connector marked audio output or audio output on the TV instead of audio input or audio input.
• Optical fiber and coaxial cable connection:
• Plug the optical cable into the connector marked Optical OUT (optical output) or Digital OUT (digital output) on the TV instead of Optical IN (optical input) or
• Digital IN (digital input).
• Plug the coaxial cable into the connector marked Coaxial OUT (coaxial output) or Digital OUT (digital output) on the TV instead of Coaxial IN (coaxial input) or
• Digital IN (digital input).
• Activate PCM (Pulse Code Modulation) in the audio setting menu of the source device (refer to the user manual of the source device).
• Audio cable connection (connected to the headphone jack of the TV):
• Turn on the TV speakers. For details, please refer to the TV user manual.

Bad sound quality|

• Press the Movie, Music, or News button on the remote control to select the appropriate sound mode.
• Set the volume of the sound bar to 75% of the maximum value (note: the maximum volume is reduced by 3 levels to 75%).
• Fix the cable connection between the sound bar and the TV (or other connected signal source).
• Try to use different source devices. If the problem persists, check the cable connection.
• Make sure that the cable connected to the source device is inserted correctly and the plug is fully inserted.
• Reduce the volume of the audio source device.
• Audio cable connection: Double-click the “up” button on the remote control to restore the volume.

Bluetooth connection: Place the Bluetooth device close to the sound bar and make sure that there are no obstacles are interfering with the connection.

Remote not working|

• Ensure that the battery is inserted correctly; if necessary, replace the battery.
• Place the remote control close to the sound bar and make sure that there are no obstacles in between. Make sure the remote control is within 16.5 feet (5 meters) of the system.
• Point the remote control directly at the infrared receiver of the system

System not responding|

• The malfunction may be caused by electrostatic discharge.
• Unplug the power adapter for at least one minute and then reconnect it.

Bluetooth device can not connect to the sound bar|

• Bring the Bluetooth device closer to the sound bar
• Turn off the device and/or sound bar, then turn it back on, and repeat the pairing process.
• Make sure that the sound bar is not connected to other Bluetooth devices.
• Make sure you have selected Sine Audio from the list of Bluetooth devices on your device.
• Make sure that the equipment you are using is correct.
• If the device is still not connected, try the following:
• Remove the sound bar (sine audio) from the “Paired Devices” list on the phone/tablet.
• Turn off the sound bar and then turn it on again.
• Pair the phone/tablet again. It should now successfully establish a pairing. Note: If none of the above solutions work, the Bluetooth device may be malfunctioning. Try another Bluetooth device. If even the new device is not connected, the soundbar may malfunction. In this case, please consult your dealer for repairs.

Warning!

• Before cleaning, make sure to turn off the system and unplug the power adapter from the power outlet.
• Do not use gasoline, alcohol, or other abrasive cleaners to clean the exterior
• Clean the surface of the system with a soft dry cloth.
• Do not use any sprays near the system. Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia or abrasives.
• Do not spill liquid into any openings.
• If you need to transport the system, please use the original packaging.

Warranty

The warranty period for this product is 12 months from the date of initial purchase. If a manufacturing defect occurs, please contact your dealer as soon as possible, and we will guide you on how to return the defective equipment to us for repair or replacement.

The following are not covered by the OXS warranty:

• The product is out of warranty
• Damage caused by abuse and abuse.
• Damage caused by chemicals, fire, radioactive materials and poisons, and liquids.
• Damage caused by natural disasters.
  If you have any question, please contact us at: service.oxs@outlook.com
  We will respond it within 24 hours!
  Only suitable for sade use under non-tropical conditions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>