circle CIM315A Contactless Smart Card Reader Module User Manual
- June 5, 2024
- circle
Table of Contents
circle CIM315A Contactless Smart Card Reader Module
Driver installation Procedure
Driver signed by Microsoft and WHQL, user can install the driver with Window Update. In case that cannot install via Window Update, please process the below steps to Manual installation
Hardware requires:
-
CIM315A
-
PC with OS windows 7 or above
Software requires: -
CIR315 Driver Package
Steps:
-
Connect CIM315A to PC
-
On PC, open “Control Panel > System”
-
Open “Device Manager”
-
Select and open “Smart card readers”
if it is shown “Microsoft Usbccid … (WUDF)”, please continue with step 5 )
if it is shown “CIR315 PICC” and “CIR315 SAM”, mean driver install completed -
Right click then select “Update driver” (one by one)
-
Select “Browse my computer for driver software…”
-
Let me pick from a list …”
-
Select “Have Disk…”
-
Select “Browse…”
Select “CIR315.inf”, then press “Open” and “OK” -
Select “CIR315 PICC” or “CIR315 SAM” then “Next”
-
Waiting until below screen shown, Press “Close” to complete
-
Double click to ensure the device changed to “CIR315 PICC” and “CIR315 SAM”
-
Done
Operation Example
Hardware requires:
- CIM315A
- PC with OS windows 7 or above
- ISO14443 Test Card
Software requires
- Any PCSC Application (e.g. APDU.exe)
Steps:
- Plug in the reader into the PC
- Open “APDU.exe”
- Click “1. Select reader”, Chose “Circle CIR315 PICC 0”, then click “OK”
- Tag ISO14443 Test card on CIM315A
- Select “T1”, Message = “90 0a 00 00 01 00 00”
- Press “2. Connect”
- Press “3. Transmit”
- Result will be shown on the “Answer from the card:”
FCC Rules
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Caution
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment. Specific
operational use conditions The end product which used the equipment have to
full test and apply an original FCC ID. Any changes or modifications not
expressly approved by the grantee of this device could void the user’s
authority to operate the equipment.
Limited modular
This equipment is applied as Limited single-modular transmitter, the end
product which used this equipment have to full test and apply an original FCC
ID.
RF Exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. The End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. The end product which used this equipment have to full test and
apply an original FCC ID.
Antennas
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment. The end
product which used this equipment have to full test and apply an original FCC
ID.
Label and compliance information The end product which used this equipment
have to full test and apply an original FCC ID. The label should be included
and comply to the FCC rules with end product’s FCC ID.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>