TARGETEVER DG011 Switch Bluetooth Gamepad User Manual

DG011 Manual
Switch Bluetooth Gamepad

Product Features:

1. Material:New ABS material
2. Buttons:Home Button/Capture Button/-Button/+Button/A Button/B Button/X Button/Y Button//ZL Button/L Button / ZR Button/ R Button/D-pad control / L3 Button /R3 Button
3. Connect Method: Connect Via Bluetooth
4. Vibration: With double motors inside, support vibration on switch console.
5. Sensor: With six-axis inside to make games feel in reality

How to Connect:

Press “Y”+” Home” Buttons simultaneously 1s to step into Bluetooth searching mode.
The four LEDs flashing will be kept light when it is connected.
PS:
Reconnect Mode: Press the Home button for 1s to wake up the controller to reconnect.
If can`t reconnect in 10s will keep sleep mode.
Console paring interface

1. How to set into the console pairing interface:
   A
   

2. 3D joystick adjustment:
   A. Press the Home button to the main interface and then choose the system settings
   B. Press the A button step into the below interface and choose to calibrate control sticks
   C. Press A step into the below interface （ from right joystick to Left joystick)
   D. Then press 3D (L3/R3) step into the below interface
   E. And then press X button step in to calibrate interface, and do actions based on the remind

Android Mode:

Press A and HOME button, LED2 and LED3 flash. When LED2 and LED3 keep lighting, the gamepad is connected.

PC Mode:

Connect gamepad to PC via charging cable. The gamepad will default into Xinput, LED1, and LED4 to keep lighting. Keep pressing “+” and “-” for 3s to switch modes between Xinput and Dinput.
When it is Dinput, LED2 and LED3 keep lighting.

Turbo/Clear Function:

1. Turn on the Turbo function by Pressing (first time) button+ABXYL1L2R1R2 to set the TURBO function
2. Turn into Auto function Pressing (Second time) button+ABXYL1L2R1R2 to set TURBO function
3. Turn off the Turbo function Pressing (Third time) button+ button which set in Turbo function to clear turbo function

Sleep Mode:

1. The console screen power off, and the controller goes to sleep mode.
2. When connected, the controller without any action for 5minutes then steps into sleep mode.

Reconnect Mode:

Based on the console not being in sleep mode, if the controller is under sleep mode, press the Home button for 1s to wake up the controller, And it will search and reconnect for the already connected console.
If couldn`t reconnect in 10s the controller will step to sleep mode.
PS: No other function buttons can wake up the controller.

Charging:

• When powering the controller, the LED1-4 flashes slow, when charging full, will be no LED flashes.
• When the controller is connected, and undercharging, the current connected LED indicator flashes slow, and when charging full, the LED indicator will keep light.
• When the controller is low power, the LED indicators flash fast to remind.

FCC Caution：

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>