Targetever B73 Wireless Gamepad or Controller Instruction Manual
- June 5, 2024
- TARGETEVER
Table of Contents
Targetever B73 Wireless Gamepad or Controller
Instruction Manual
Connection Instruction
Pair & Connect: Press Y and Home Button Simultaneously
Step 1 : Find Controllers Option—Click Change Grip/Order.- Image 1/
Image2
Step 2: Press and hold the Y and HOME button simultaneously, until the 4
LED lights flash in turn for 2 seconds, then release your finger and wait for
the connection to complete.- Image 3
NOTE: Enter the Change Grip/Order page, please complete the connection
within 30 seconds as soon as possible. If you stay on this page for too long,
you may not be able to connect to the NS console. – Image 3
Reconnect [Home]
Reconnect: Press Home Button
If your controller was once paired and connected to your NS console, next time
you can press the Home Button to make it to be rapidly connected.
Note:
For reconnecting, please turn on the NS console first, does not support
pressing the Home button to wake up the console under standby mode.
Unable to connect, please follow under three steps to solve:
- Turn off airplane mode.
- Delete the information of this controller and sensors-disconnect controllers.
Follow the first-time connection method and re-pair again.
Adjust Turbo Speed
Buttons can be set to the turbo speed(is called for short function
buttons) :
A/B/X/Y/L/ZL/R/ZR button
Enable/disable the manual and auto turbo speed function:
Step1 : Press the 
button and one of the function buttons
simultaneously, to enable the manual turbo speed function.
Step 2 : Repeat step 1, to enable the auto turbo speed function.
Step 3: Repeat step 1 again, to disable the manual and auto turbo speed
function of this button .
Disable all the button’s turbo speed functions: Press the “-” button and
the down button of the direction button simultaneously.
There are 3 levels of turbo speed:
Minimum: S shoots per second, and the corresponding channel light flashes
slowly.
Moderate: 12 shots per second, the corresponding channel light flashes at a moderate rate.
Maximum: 20 shots per second, the corresponding channel light flashes quickly.
How to increase the turbo speed: When the manual turbo function is on,
upward the right joystick meanwhile press the 
button for S seconds, which can increase one level of turbo speed.
How to decrease the turbo speed: When the manual turbo function is on,
downward the right joystick meanwhile press the button for S seconds, which can decrease one level of turbo speed.
Adjust Vibration Intensity
There are 4 levels of vibration intensity: 100%-70%-30%-0%(no vibration)
How to increase the vibration intensity:
Press the “+” button and the up button of the direction button simultaneously
for 5 seconds, which can increase one level of vibration intensity.
How to decrease the vibration intensity:
Press the “-” button and the up button of the direction button simultaneously
for S seconds, which can decrease one level of vibration intensity.
FCC Caution :
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>