ifrogz Airtime ANC Wireless Earbuds with Charging Case User Guide

: June 5, 2024
: iFrogz

Table of Contents

ifrogz Airtime ANC Wireless Earbuds with Charging Case
Introduction
MUSIC CONTROLS
CALL CONTROLS
ANC CONTROLS
Getting the Best Fit
Charging the Wireless Earbuds
Factory Reset
Having Trouble?
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ifrogz Airtime ANC Wireless Earbuds with Charging Case

Introduction

Welcome to truly wireless audio and our highly-coveted ANC earbuds with up to 25 hours of noise-canceling playtime.

Pairing the Wireless Earbuds with Your Device

Simply open the case with the earbuds still inside. Press and hold the pairing button in the center of the case for two seconds.
The two left and right LEDs on the case will alternate flashing.
A pairing signal will be sent to your Bluetooth® device. On your device, go to Bluetooth under Settings and select “IFROGZ® Airtime ANC.” Complete any additional steps your device may require. Remove the earbuds from the case.

MUSIC CONTROLS

CALL CONTROLS

ANC CONTROLS

Using the Earbuds
Airtime ANC true wireless earbuds have built-in touch navigational controls. Just press on the top of the earbud stem to navigate.

Turning Earbuds On/Off

To turn the earbuds on, simply remove the buds from the case.
To turn the earbuds off, simply place the buds back in the case and close the lid.
If ANC or Pass Through mode is not active, the earbuds will go into hibernation mode if not used for 20 minutes.

Getting the Best Fit

To get the best sound out of your earbuds, you need to have the right size ear tip to form a good seal. That’s why we provide different sized tips. If your ear tip feels loose, try a larger size. If you feel too much pressure, or if the ear tip doesn’t fit inside your ear, try a size smaller.
Note: each of your ears may require a different-sized tip.
To see if you’ve got a good seal, try the yawn test. Put in your earbuds and give a nice yawn; if your earbuds don’t wiggle and don’t break the seal, then you’ve got a good fit.

Charging the Wireless Earbuds

The case carries enough power to charge the earbuds up to 4 times*.

Place the earbuds in the charging case. You’ll feel them magnetically click into place.
Once in the case, the leftmost and rightmost LEDs will quickly flash every 8 seconds to indicate the earbuds are charging.

Once fully charged, the LEDs will stop flashing.

Charging the Case
Your case comes charged and ready to go. You can re-charge the case wirelessly using a wireless charging pad, or charge the case manually using the included USB-C® cable.

Wireless Charging

Simply drop the charging case on a compatible wireless charging pad.
The Battery Indicator light will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will turn off.

Manual Charging

Connect the included USB-C charging cable to the port on the side of your case.
Connect the USB-A end of the cable to your preferred 5V USB outlet.
The Battery Indicator light will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will turn off.
Disconnect the charging cable.

Quick Charge Feature
Get one more hour of playtime by nesting the earbuds in the charging case for ten minutes.

Checking the Battery Level
Your case carries enough power to charge your wireless earbuds 4 times for a total of 25 hours. To check how much power your case still has, place the earbuds in the case. The LED on the front of the case will illuminate, indicating how much battery remains in the case:

If four lights illuminate, 75% or more remains
If three lights illuminate, between
50-74% remains
If two lights illuminate, between
25-49% remains
If one light illuminates, less than
24% remains.

Factory Reset

If you have functionality issues, a factory reset can help. Here’s how to perform one.

Place both buds in the case.
Press and hold the center pairing button for 20 seconds.
The case LEDs will illuminate in a wave from left to right and then from right to left.
The earbuds are now reset to the factory settings.
Go into your device’s Bluetooth settings and remove the Airtime ANC earbuds.
Then re-pair them to your device.