SKY RIDER MINI GLOW PRO Quadcopter Drone User Guide

SKY RIDER MINI GLOW PRO Quadcopter Drone

Warnings & Precautions

Important Safety Instructions

• Read and follow all instructions.
• Keep these instructions for future reference.
• Heed all Warnings.
• Intended for children ages 14 and higher. Adult supervision is required.
• Only use attachments/accessories specified by the manufacturer.
• Before flying, always check the body, rotors, and battery for any damage or obstructions.
• Battery should be free from cracks or swelling.
• Keep the rotors clear of any obstructions and body parts to avoid potential damage and injury.
• Manufacturer and dealer assume no liability for accidental damages from improper use or installation of parts, or from damage incurred from worn or broken parts.
• Pilots are responsible for their actions and any damage caused from improper use.
• Pilots should keep the craft in sight at all times during flight. If you lose sight of the craft at any time, power down and cease flight immediately.
• Only fly in large, open areas that are free from obstacles or potential hazards, such as trees, power lines, ceiling fans, and the like.
• Flying over bodies of water is not recommended.
• Flying at night is not recommended.
• Never try to retrieve the craft from areas you cannot safely reach, such as rooftops or trees.
• Never launch the craft from your hand.
• Never leave the craft unattended while it is powered on or while the battery is charging.

FCC Warnings

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings & Precautions

• WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing.

• CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in personal injury.

• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of according to state and local guidelines. They should never be disposed of in normal household waste, and they should never be incinerated, as they might explode. Contact your local government for disposal or recycling practices in your area.

• WARNING: Shock hazard – Do Not Open.

• Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
  Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

• Do not mix old and new batteries.

• Completely replace all old batteries with new ones.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (NiCad, nigh, etc.) batteries.

• Batteries should be recycled or disposed of as per state and local guidelines.

• WARNING: This product may contain chemicals known to the State of California to cause birth defects, or other reproductive harm (California Prop 65). Wash hands after handling.

• This product meets and complies with all Federal regulations.

Mini Glow Pro Quadcopter Drone

Features

• 6-axis gyroscope
• 3 speed settings
• Control distance: 65 ft.
• LED navigation lights
• Rotors
• Free app for Wi-Fi flight
• Wi-Fi camera
• Built-in, rechargeable lithium-polymer battery power
• USB port for battery recharge
• Operating time: 8-10 minutes
• Charge time: 50-70 minutes

Includes

• Smartphone cradle
• 2.4 GHz remote control: requires 3 AAA batteries (not included)
• USB cable for battery recharge
• Screwdriver
• 5 replacement rotors
• User’s guide

Overview

Craft Layout & Features

Charging the Battery

Rotor Guards

Battery Charging Procedure

The craft’s battery must be charged before it can be flown. Before charging, be sure the craft and remote control are powered OFF to avoid risk of injury or damage.
Connect the charging cable (included) to the USB port of a powered ON computer or USB power adapter (not included), then connect the charging plug to the unit. Be sure to correctly match the plug to the charging port or damage may occur. Charge fully before use for maximum performance and flight time. Charging time is approximately 50-70 min.
While charging, the cable will display a red light.
When charging is complete, the light will turn OFF.

• REMINDER: Do not charge overnight. Do not leave unattended while charging.

Remote Control

Functions

Battery Installation

Flying

Craft/Remote Link
Before flying, the craft and the remote must be linked together and the gyroscopes on the craft must be allowed to calibrate.
Begin with the battery installed and the craft and remote powered OFF.

• Step 1
  Place the craft on a flat, level surface. This is necessary for the craft’s gyroscopes to properly align.

• Step 2
  Power the craft ON. The LED lights will blink in unison as the craft searches for a signal from the remote.

• Step 3
  Power ON the remote. The light on the remote by using the power switch at the bottom of the remote. The Indicator will blink as it searches for the signal from the craft. An audible chime will sound when the remote and the craft have linked with each other.
  

Flying

• Step 4
  Simultaneously push the Left Control Stick fully downward and the Right Control Stick down and to the left as shown in the figure. Wait for a chime to sound, when this chime has sounded the craft is ready to fly.

• Step 5
  Use the Left Control Stick to take off and control the throttle for ascension and descension
  Use the Right Control Stick to control the Pitch (forward/backward) Yaw (spin) movement of the craft.

When You’re Done Flying

After landing, pull the Left Control Stick (throttle) fully downward to power down and wait for the rotors to stop spinning. Power OFF the remote BEFORE powering OFF the craft. This will ensure that no signals are accidentally sent by the remote, reducing the chance of injury. After this is done, it is safe to pick up and power OFF the craft.

Emergency Stop

If the craft is having difficulty flying, is out of control, or otherwise behaving erratically, you can press and hold the Emergency Stop button to stop the rotors and the craft will fall to the ground.

Trim Adjustment

Setting Trim & Countering Drift

Even after the craft is calibrated, it may show a tendency to drift while airborne. Adjusting the trim will help counter this effect and allow for better control the craft.

• To avoid potential damage, adjust the trim while attempting a stable hover.
• Try to avoid making any exaggerated movements with the flight controls.
• Adjust one trim setting at a time to avoid confusion.

Remember, the white rotors and LED lights indicate the front of the

craft.

Adjusting the trim will help with drift but it will not entirely eliminate it. Turbulence and other factors may still influence the craft’s flight characteristics.

If the craft is spinning clockwise by itself, you may need to use the left trimming button to counter this movement.

If the craft is spinning counter-clockwise by itself, you may need to use the right  trimming button to counter this movement.

Trim Adjustment

Gyroscope Recalibration

If the craft is experiencing difficulty flying or is behaving erratically, it’s gyroscopes may need to be recalibrated. Do not attempt to do this while flying, safely land the craft first and place it on a flat surface. The craft and the remote should already be linked together.
Simultaneously push the Left Control Stick fully downward and the Right Control Stick down and to the left as shown in the figure. Wait for a chime to sound, when this chime has sounded the craft is recalibrated.

Flying Tips & Features

Tips for Safe Operation

• It is recommended to only fly in large, open spaces that are free of obstacles like power lines, trees, ceiling fans, etc.
• When flying indoors, avoid walls and ceilings, as the craft will be drawn towards them if closer than 2-3 feet.
• Stand behind the craft when first taking off, so that you and the craft are facing the same “forward” direction. This will help with orientation when the craft is airborne.
• Remember: the blue LED navigation lights indicate the front of the craft.
• Novice pilots should move the controls slowly and deliberately to get used to the craft’s flying characteristics. Try using one control at a time.
• Practice basic flight operations like take off, hovering, and landing.
• If you crash, power down the engines IMMEDIATELY to reduce the chance of damage or injury.
• If anything obstructs the propellers for any reason, throttle down IMMEDIATELY and safely clear the obstruction. Check for possible damage before flying again.

Speed Setting

Press the Speed button on the remote control once to set the craft’s speed.

• Low: Provides smooth and predictable control of the craft. The remote will chime once to indicate the low speed setting.
• Medium: The craft will move and respond faster to all control inputs. The remote will chime twice to indicate the medium speed setting.
• High: Highest setting for maximum performance. The remote will chime three times to indicate the high speed setting.

Flying Tips & Features

Auto-take off/Landing

Before attempting Auto-take off/Landing, be sure that there is ample clear space around the craft, ideally 9-10 ft. in all directions. It is not recommended to attempt Auto-take off/Landing around or through any obstacles, as this may result in unintended damage.
Press the Auto-take off/Landing button. The craft will automatically begin to hover about 4 feet from the take off point.

Sky Rider Cruise App

The Sky Rider Cruise app will display the image from the craft’s camera on your smartphone’s screen, allowing you to capture images and video of your flights. Connect your smartphone to the craft’s Wi-Fi signal and start flying!

Free Download
Scan the appropriate QR code with your smartphone or search for “Sky Rider Cruise” in the Apple App Store or Google Play Store.

Connect to Wi-Fi
NOTE: Wi-Fi control may be interrupted by interference from other nearby Wi-Fi equipment.

Before beginning, make sure your phone’s Wi-Fi is enabled and the craft is powered ON.

• From your smartphone, open the Wi-Fi settings menu, then search for and select Sky Rider Cruise xxx to connect to the craft.
• Once connected, open the app. You will see the Home Screen (image below). From here you can adjust settings and start using the app.
  

Settings Screen

Altitude Hold/Hover- This setting will lock the aircraft at the altitude it is currently at.
Right Hand Mode – Reverses the locations of the Left and Right flight controls on the screen.

Sky Rider Cruise App

Screen Controls

Gravity Sensor Mode uses the G-Sensor in your phone to control the craft. Tilt the phone forward, back, left and right to control the pitch and roll of the craft. Throttle and yaw are still manually controlled from the Left Directional Control.

Camera & Video
Use the Photo and Video buttons to document your flight. Images and video are saved to your phone and can be viewed later by pressing the Gallery button.

Flight Controls

Sky Rider Cruise App

Using the Remote & App Together

It can be easier to capture photos and video by using the remote to fly the drone and using the app in a viewing only method. Use the app and the remote together by attaching the smartphone holder (included) to the remote and placing your phone in the holder.
Follow the steps below to connect to the remote and the app in the proper sequence.

• First, connect the remote to the craft like normal. Connecting the remote first overrides any control signals from the app.
• Next, use your phone to connect to the craft’s Wi-Fi. Open the app and go to the Flight Screen. Leave the Flight Controls off for the best view from the drone’s camera.
• Use the controls on the remote to fly the craft while the Wi-Fi camera streams to your phone.
• When you’re finished flying, power down the remote and craft like normal.
  

Parts & Repair

REMINDER: Pilots are responsible for any damage caused by improper use.

Parts Replacement

Standard parts such as extra batteries and remotes are available online for purchase when in stock. However, any non-standard parts such as cameras, screws, bodies, etc. can be ordered by placing an inquiry with our parts department at: partsinfo@dpiinc.com.

Rotor Replacement

The craft comes with replacement rotors if the originals are broken or badly damaged. Use the included screwdriver to remove the rotor retaining screw that holds the rotor to the motor shaft. Once the retaining screw is out, pull upwards on the rotor to remove it from the motor shaft. Installation of the new rotor is the reverse of the removal process. Be sure to tighten the rotor retaining screw firmly, but do not over tighten.

It is extremely important to use the correct rotor (A or B) for replacement.
Using the incorrect rotor will make the craft impossible to control. The marking can be found on the rotor near the shaft.

3D Mode
VR Mode splits the phone’s screen for use in a VR headset. Press the 3D button on the screen to turn this feature ON or OFF. Use VR Mode to give a friend a fully immersive, point-of-view flying adventure.

NOTE:

• On screen flight controls are locked out in VR Mode. You must have the regular remote connected in order to fly the craft.
• We do not recommend flying the craft while wearing a headset. The craft’s camera has a limited forward view and the headset will completely obscure the user’s peripheral vision and situational awareness. Pilots assume all risk and are responsible for any damage caused by improper use.

Troubleshooting

If you are experiencing problems using or flying the craft, consult this table.

• Poor contact between power plugs.
•Craft is out of range.| •Check remote batteries, replace if needed.
•Check craft battery, be sure it is fully charged.
• Be sure the power plugs are firmly connected.
• Be sure the remote has an unobstructed line of sight to the craft.
• Remain within the remote’s 65 ft. range.
Craft is difficult to control or flies erratically.| •Gyroscopes may be misaligned.| • Recalibrate gyroscopes (see pg. 13).
•Power OFF remote and craft and reconnect (see pg. 10).
Craft drifts while in flight.| • Trim not set or needs adjustment.| •Adjust trim settings (see pg. 12).
Craft suffers from mechanical trouble.| •Damage to body, rotors or other major components.| • Repair or replace parts as needed.
LED lights ON but craft does not respond to controls.| •    Low battery power.| •    Recharge the battery.

Customer Support

Contact Information

• Website: www.gpx.com
• Email Support: prodinfo@dpiinc.com
• Email Parts: partsinfo@dpiinc.com
• Phone Support: 1-888-999-4215

Warranty

See included 30 Day Warranty for warranty information. Warranty and the most up-to-date version of this User’s Guide can also be found at: www.gpx.com

International Support

To download this User’s Guide in English, Spanish, and French, or to get answers to frequently asked questions, visit the support section at: www.gpx.com

References

• gpx.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>