carewell DC7 DC Power Ceiling Fan Remote Control User Manual

June 5, 2024
carewell

DC POWER CEILING FAN REMOTE CONTROL MANUAL

INSTALLATION INSTRUCTIONS

NOTE:
This unit is to be used for the control of DC power ceiling fan and in an AC120V 60Hz power supply only. Output Power: 50W (Max.) for motor and 30W (Max.) for LED light. Important: Using a full range dimmer switch (not included) to control fan speed will damage the fan. To reduce the risk of fire or electrical shock, do not use a full range dimmer switch to control fan speed.

  1. Switch power off at fuse box or circuit breaker before you begin installing the fan.
  2. Make wiring connections as indicated Fig. 1.
  3. Launch distance for remote control: about 10m.
  4. The remote code setting process:
    Step: 1 Open the remote battery cover and install DC1.5V/AAA 2pcs alkaline battery, with the fan power off. (Fig. 2)
    Step: 2. Within 30 seconds of restring power to the fan, you must use a ball pen or tool to press “Learn” button about 2 seconds. Once the receiver has detected the frequency, the receiver will make sound, Bi once. This will indicate the receiver has learned the frequency that
    was previously selected on the transmitter.

FIG. 2
Note: After the AC power is on, do not press any other button on the transmitter before setting learning. Doing so will cause the procedure to fail. After completing the steps above, you should be able to operate the ceiling fan and light. If the fan is not responding to the transmitter, please turn the power off to the receiver. And repeat step 2.

LIGHT FUNCTION SELECT SWITCH

If installed energy light onto ceiling fan, please slide the dip switch, light function select switch, to “O” position. If installed dimmable LED light onto ceiling fan, please slide the “light function select switch” to “D” position. (Fig. 2)

FUCNCTIONS OF REMOTE CONTROL: (Fig. 3)

Turn off the ceiling fan.

Fan speed: Press and release immediately to turn on and set fan speed. (6 is for the highest fan speed)

Light button: ON/OFF- Press and release immediately to turn on or off light. DIMMER-Press and hold to dim or brighten light to the desired level and release. (LED only and light function select switch on dimmer position.)
Sleep Timer:
: The fan will turn off after 2 hours automatically.
: The fan will turn off after 4 hours automatically.
: The fan will turn off after 8 hours automatically.
Natural breeze: Fan speed will modulate to simulate a natural breeze.
Reverse button: Press and release immediately to set fan direction. The fan runs counterclockwise. Airflow will provide a downward cooling breeze. The fan runs clockwise. Airflow will force warm air downward without a noticeable breeze.
When you press transmitter button, the receiver will make sound, Bi, once as receiving setting signal.
If the red LED indicator of transmitter is not working as you pressing button, you need to change and use new batteries.

INSTALLING WALL MOUNTED HOLDER

Attach wall mounted holder using the two provided screws. (Fig. 4)

|
---|---

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals