Carewell FAN63T Remote Controller Instruction Manual

: June 12, 2024
: carewell

Table of Contents

GENERAL INFORMATION
INSTRUCTION OF INSTALLATION AND OPERATION
SETTING THE CODES
INSTALLING RECEIVER IN CEILING FAN
OPERATING TRANSMITTER:
TROUBLE SHOOTING GUIDE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Remote controll

GENERAL INFORMATION

This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and oﬀ .
The light dimmer button will control the light brightness dimmer and oﬀ.
The blue indicator on the transmitter will light when one of the six buttons is pressed.

INSTRUCTION OF INSTALLATION AND OPERATION

SETTING THE CODES

This unit has 16 diﬀerent code combinations. To set the codes, perform the following steps:
A.Setting the codes on the transmitter:
a.Remove battery cover.Press ﬁrmly on the arrow and slide battery cover oﬀ.
b.Slide codes witches to your choice of up or down position.Factory setting is all up.Do not use this position.
Use a small screw driver or ball point pen to slide ﬁrmly up or down(Figure1).
B.Setting the codes on the receiver:
a.Slide codes witches to the same position as set on your transmitter(Figure2)
b.Replace battery cover on the transmitter.

INSTALLING RECEIVER IN CEILING FAN

A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by removing fuse or switching oﬀ circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0, Maximum light watts: 140W for incandescent or 60W for LED.
Otherwise power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting bracket.
c. Disconnect existing wiring between ceiling fan and Supply in electrical junction box.
d. Make connections as follows, using the wire nuts supplied: If other fans or supply wires are diﬀerent color, have this unit installed by qualiﬁ ed licensed electrician.
e. Push all connected wires up into junction box.
f. Lay the yellow antenna wire on top of the receiver, and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power. CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees, For Mounting Controller, Model AC8.3T
CONNECT TO
Green fan wire ….Bare supply wire
Black receiver wire(AC IN L) ….Black supply wire
White receiver wire(AC IN N) ….White supply wire
White receiver wire(TO MOTOR N) ….White fan wire
Black receiver wire(TO MOTOR L) ….Black fan wire
Blue receiver wire(FOR LIGHT) ….Blue light wire

OPERATING TRANSMITTER:

A. Install 3 volt battery(not included). (To prevent damage to transmitter, remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. In order to prevent possible interference from or to other remote units such as garage door openers, car alarm or security system. If you ﬁ nd that your fan and light kit go on and oﬀ without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
3 key -for fan speed HI.
2 key -for fan speed MED.
1 key -for fan speed LOW.
OFF key -for fan oﬀ.
TIMER key -for FAN-TIMER 2,4,8H.
LIGHT/DIMMER key -for light brightness and oﬀ.
The light function is controlled by pressing the LIGHT/DIMMER key down to increase or decrease light.
Tap key quickly to turn light oﬀ or on.
Keep pressing the button in excess of 0.7 second and it becomes a dimmer, the light varies cyclically in 0.8 second.
The receiver can remember the last status of the light brightness when the light was switched, so that it can resume to adjust the light brightness.
FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may casue harmful interference to radio communications,
However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit diﬀ erent from that to which the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
Industry Canada Notice This device complies with Industry Canada licence- exempt RSS standard(s).
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. authority to operate the equipment.

YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
Optional Wall Mounting for Transmitter Holder Place in accessible area of your home, and screw the transmitter holder into wall using the two screws provided, slide hand unit into holder.

TROUBLE SHOOTING GUIDE

Fails to operate
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
f. Code set at exact same positions in both transmitter and receiver ?
Won’t operate at distance
If transmitter operates fan/light kit when up close, but not at 20 feet away.
Try placing the yellow antenna wire higher, up through ceiling/outside the junction box.

NOTICE !
Your ceiling fan and light kit assembly must meet the following requirements:

Do not use with solid state fans.
Electrical rating: 110/120v 60Hz 3.5A
MAX. Motor amps: 1.0
MAX. Light watts: 140W for incandescent or 60W for LED.

WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.