Xiaoyan SD01 Terncy Smart Dial Smart scene Controller User Manual

SD01 Terncy Smart Dial Smart scene Controller
User Manual

Smart Dial Introduction

Tenancy Smart Dial is a small but powerful control terminal. You can easily pull the curtain, change the color temperature or brightness of light, adjust the volume of sound, and control the on-off state of any other switches with only one Smart Dial, which lets you enjoy intelligent life in a natural way.
* The Smart Dial follows ZigBee 3.0 wireless protocol.

Install Guidance

1. Install the button cell battery into the Smart Dial.
2. Remove the adhesive tape from the base and place it as required.
3. Fix the Smart Dial on the base.

Indicator Light State

Indicator State| The green light flashes 10 times per sec| Connecting to Home Center nearby
---|---|---
The green light flashes every 2 sec.| Successfully connected to Home Center
Red light flashes 4 times per sec.| Failed to connect to Home Center

Download and Install App

Download the Tenancy app from app markets or scan the QR code below. Follow the instructions within the app to connect the Switch Module to Home Center.

http://xiaoyan.io/app

Setting Up The Accessory for The First Time

1. Click the “Add Device” button in the Device tab of the Tenancy app.
2. The new device can be found after 3 sec

Set Up The Accessory Again

1. Click the “Add Device” button in the Device tab of the Tenancy app.
2. Long press the button for 8 sec, the device will be found after 3 sec.

Set Up Automation

1. Enter the “automation’ page of the Temcy app to set up automation.
2. Take the “if.. then.. “automation type as an example.
   1. Set if ‘directive for the condition;
   2. Set then’ directive for action;
   3. Name the automation.

• Smart Dial supports rotation and press directive. It can simultaneously control the curtain motor, light, switch, stereo volume, and other equipment.
  Automation type provided:
  a. “Schedule” Is set for the directive at a specific time.
  b.” Countdoweis set for directive after a countdown.
  c. then.7is set for the custom directive.

Application Scenarios

1. Control Curtain
   Choose “if… then..:’ automation and set rotation as the condition, then select the curtain motor to execute the action. After that, you can naturally control the curtain by rotating Smart Dial.

2. Adjust Light
   Choose “if… then..:’ automation and set rotation as condition, then select light to execute the action. After that, you can adjust the light by rotating Smart Dial.

3. Change Volume
   Choose “if… then..:’ automation and set rotation as condition, then select stereo equipment to execute the action. After that, you can change the volume by rotating Smart Dial.

4. Control Switch
   Choose “if…then…” automation and set keypress as condition, then select switch to execute the action. After that, you can control the switch by pressing Smart Dial.

Notes 1

1. Do not soak or wash your devices.
2. Keep products away from fire, high temperatures, or any other extreme environment.

Notes 2
Home Center is required to enable Smart Dial to work with HomeKit technology. See https://www.terncy.com for more details.
Notes 3
We reserve the right to change or modify the manual.

Warranty Card

Xiaoyan’s after-sales service includes:
Xiaoyan Tech shall remove any physical defects inherent in the device which are listed on the warranty card, free of charge, by replacing (at the sole discretion of Xiaoyan Tech) the defective device within a period of 15 days from the date of receipt by the consumer, and by repairing the defective components of the device within the period of 12 months from the date of receipt by the consumer.
*The warranty may vary in different countries and regions.

The Warranty Applies to:

1. surface damage resulting from mishandling during transport, or defects inherent in the material or structure of the products;
2. failure of the buttons or indicator lights;
3. failure of wireless communication.

The Warranty Does Not Apply:

1. when the warranty period has expired;
2. to damage resulting from repairing and introducing alterations by unauthorized persons;
3. to damage caused by using accessories not recommended by the manufacturer;
4. to damage resulting from other avoidable causes.

FCC Statement：
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

http://weixin.qq.com/r/kzuSiorEEddurc7p926B

Twitter official account

Contact Us
Online Support: https://www.terncy.com/service
Telephone: 400-920-2823
E-mail: support@terncy.com
Shanghai Xiaoyan Technology Co., Ltd. Made in China
Room 502, Buiding E, No.666, Shengxia Road, Shanghai,China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>