Speedefy KX450 AX1800 Dual Band Gigabit WiFi Router User Guide
- June 6, 2024
- Speedefy
Table of Contents
Quick Start Guide
AX1800 Dual Band Gigabit WiFi Router I Model: KX450
Status Light
|
Description
---|---
Solid on| Starting up or connected to the Internet.
Blinking slowly| Failed to connect to the Internet.
Blinking rapidly| A device is connected to, or removed from, any port.
Blinking for 2 mins| Awaiting the WPS connection.
Power Port | Connect the included AC power adapter. |
---|---|
Reset | Reset: Use a sharp object to press it for 8 seconds to factory reset |
your router.
WPS| WPS: Press it to connect to the WPS-enabled network devices.
WAN Port| Connect an Ethernet cable to this port, and to a broadband Internet
cable/DSL or fiber modem.
LAN Ports
(1, 2, 3,4)| Connect Ethernet cables to these ports, and to wired devices on
your network.
Scan the QR Code to get the video guide.
https://register.speedefy.com/setup
Install Your Router
- Turn off your modem, cable the modem to the router’s WAN port.
- Turn on the modem and wait 2 minutes for it to restart.
- Connect the power adapter to the router and turn it on.
- Flip to the next page to continue with the setup.
I If your Internet comes from an Ethernet outlet, please connect the router’s WAN port to it, and then follow Step 3 and Part 2: Two Methods to Setup.
I If you want to configure this router as an access point(similar to a WiFi extender) to extend the existing network, please refer to the Access Point Mode section on the next page.
Can Not Connect to WiFi 6 Router Wirelessly?
Some older versions of driver or software for wireless devices may be incompatible with the WiFi 6 router. If you are experiencing problems connecting to the WiFi 6 router, please update the driver or software for your wireless devices. How to update the driver? (1) Check the model lot for your wireless adapter. (2) Go to the manufacturer’s website for the latest driver version. (3) Update the driver. You can also contact the adapter manufacturer for further assistance in updating.
Ways to Reset the Router
- With the router powered on. press and hold the WPS/PST button on the back until the Power LED starts blinking.
- Log in to the web management page of the router. go to Administration > Device Management, and click Reset.
- Go to Speedy WiFi App. On the Tools page. Click Reset. The router will reset automatically.
AP (Access Point) Mode
In this mode. the Speedefy router can work as a WiFi extender to turn a wired network into a wireless network. extending the WiFi range.
- Connect the existing router to the Speedefy Router. Cable Speedefy router’s WAN or LAN port to your existing router’s Ethernet port. as shown above.
- Connect a computer to the Speedefy router. Use an Ethernet cable, or wirelessly by joining the default SSID printed on the label.
- Log in to the Speedefy router. Visit http://speedefywifi.com in a browser. Complete the instructions if this is the first time you’re setting up the router.
- Enable AP Mode. Go to Internet Settings, select AR and click Save. Wait for the router to reboot. It will complete the AP Mode setup automatically.
FAQ
For more questions and answers, please visit
www.speedefy.com/faq
Q1: What connection type to choose if the router failed to detect
automatically?
Type|
Description
---|---
PPPoE| Applicable to use if your ISP provided a PPPoE username and password.
DHCP| Obtain IP address from ISP automatically. If your ISP does not provide a
username and password, choose DHCP to connect.
Static IP| Ask configurations from your ISP if you are using a static IP.
Q2: Why cannot I access the Internet after installing the router?
- Try connecting a computer directly to the modem via an Ethernet cable. then check if you have Internet access. If not, contact your ISP.
- Check if the router’s WAN port is connected to the modem properly. and confirm the status of the indicator.
- If your wired devices cannot access the Internet:
- Confirm if your PC is connected to a LAN port properly.
- Make sure your PC is set to obtain an IP address automatically and Obtain a DNS server address automatically.
- If your WiFi-enabled devices cannot access the Internet: 1) Reboot the router and reconnect to the WiFi. If it doesn’t work. factory reset the router and repeat the router setup process.
Q3: Why cannot I access the web management page?
- If the computer is set to a static IP address. change it to obtain an IP address automatically.
- Disable the proxy server, if enabled. Also. disable the VPN software.
- Disable and re-enable the network adapter being used on your computer.
- Ensure that http://speedefywifi.com is correctly entered in the web browser. Alternatively. visit 192.168.3.1
- Use another web browser and try again.
- Reboot your router and try again.
Q4: How to register an account in Speedy WiFi APP?
- It is recommended to sign in with a Third-Party login such as Gmail or Apple ID(if using an OS device).
- If you want to register with an email account:
- Enter your email account and password and click Register.
- An activation email will be sent to the mailbox. Remember to click the
activation link in the email.
PS:
1. Try to use a common browser such as Chrome, Edge, Firefox, and Safari to open the link.
2. Check the JUNK MAIL of the mailbox if you can not find the activation email.
Note: If you fail to register. try to use a common email such as Outlook, Gmail, or Yahoo and try again.
Q5: Why my download speed cannot reach the advertised speed rate?
- Devices under 2.4G WiFi will get a lower speed than 5G WiFi. Also, the wired connection will deliver a higher speed than a wireless connection.
- Check if there are multiple users sharing the connection at the same time. Try to limit their speed, or if required. even block them in the web management page or Speedy WiFi App.
- Check the Internet speed and link quality from your ISP. If the Internet is 100Mbps, you can get up to 12.5MBps download speed. (1 Byte=8 bits) Actual speeds may vary due to transmission loss.
- Place the router in a central location instead of the corner to improve wireless performance. All antennas should be upright.
- Try to connect the gigabit port of the modem to the router using a cat5e Ethernet cable, or better.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device. pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates. uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions. may cause harmful interference to radio communications. However.
there is no guarantee that interference will instructions. may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on. the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radiofTV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 22 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provided with antenna
installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference. and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Operating frequency: 2412-2462MHz. 5150-5250MHz, 5725-5850MHz.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures. Operations in the 515-5.25GHz band are restricted to indoor use
only. This equipment should be installed and operated with a minimum distance
20cm between the device and your body. NOTE:
(1) The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment.
(2) To avoid unnecessary radiation interference. it is recommended to use a
shielded RJ45 cable.
WARNING: The mains plug is used as a disconnect device, the disconnect
device shall remain readily operable.
Declaration of Conformity
Hereby. SHENZHEN TENO NETWORK TECHNOLOGIES CO., LTD. declares that the radio equipment type KX450 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://wwwspeeciefy.com/regulations-ce/
Operating Frequency:
2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.86 dBm
5 GHz: 22.96 dBm
Software Version: V16.03.15.XX 46. in
Caution: (KX450)
Adapter Model: BN074-A18012U/ BN074-A1801281 BN074-418012E
Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO.. LTD.
Input: 100 – 240V AC. 50/60Hz. 0.6A
Output: 12V = 1.5A =: DC voltage
RECYCLING
This product bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. The user has the choice
to give his product to a competent recycling organization or to the retailer
when he buys new electrical or electronic equipment.
Operating Temperature: 0°C – 40°C
Operating Humidity: (10% – 90%) RH. non-condensing
Install Your Router
- Turn off the modem, cable the modem to the WAN port on the router.
- Turn on the modem and wait 2 minutes for it to restart.
- Connect the power adapter to the router, and turn it on.
1 If your Internet comes from an Ethernet outlet, please connect the router’s WAN port to it, and then follow Step 3 and Part 2: Two Methods to Setup.
1 If you want to configure this router as an Access Point(similar to a WiFi extender) to extend the existing network, please refer to the Access Point Mode section on the first page. Ill
Set up Your Router
Method 1: Via Web Browser
1. Connect your device to the router (Wireless or Wired)
Wireless
-
The default SSID is printed on the label of the router.
-
Enable WLAN function of your Smart devices or PC.
-
Join the default SSID that displays in the list.
• Wired
For a wired connection, use an Ethernet cable to connect your computer to a LAN port on your router.
Connect the router to the Internet.
-
Log in to the router Launch a web browser, enter http://speedefywifi.com or 192.168.3.1, and a login page displays.
PS: If the login page does not display, please refer to Q3 of FAQ.
-
Choose the connection type.
The webpage detects your connection type automatically. If detection fails, choose your connection type manually. Then follow the step-by-step instructions of the Quick Setup Wizard to connect to the Internet.
Method 2: Via Speedy WiFi App
- Download the Speedy WiFi App from App Store or Google Play.
- Connect your smartphone to the default SSID printed on the label of the router.
- Launch the Speedy WiFi App.
- The App will detect your connection type automatically. Follow the instructions in the App to connect to the Internet.
Scan the OR code to download the app and get more support.
https://register.speedefy.com/setup
Customer Service
https://register.speedefy.com/setup
Scan the QR code, get Video Setup, and more support.
www.speedefy.com/help
cs@speedefy.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>