Shenzhen Xinhuamei Electronics F9-5 True Wireless Earbuds User Manual

June 5, 2024
Shenzhen Xinhuamei Electronics

F9-5
Product introduction

TURN ON
Method 1 Take out the earbuds from the charging case,the earbuds will turn on automatically. The led indicator will flash red and blue
Method 2: Touch and hold the MF button for 2-3 seconds

TURN OFF
Method 1. Touch and hold the MF button for 2-3 seconds to turn OFF the Earphone, the led indicator will flash red rapidly then lights off.
Method 2. Put back the earbuds into the charging case , the earbuds will turn off automatically and start being charging

Tips If the earphone without pared any mobile device both units will be turn off after 5 munites; or if the Bluetooth distance is beyond 10 12m and without paired any device, both units will be turn off after 5 munites

Take out both earbuds from the charging case, it will auto turn on and auto paired with each other. Once paired, the led indicator will flash red & blue quickly.

Tips If pairing Is unsuccessful, Touch and hold the ME button on both Earphone around 5 seconds simultaneously till the led indicator flash b:ue ONE time; Then turn on both unit again, they will auto-pairing

Activate the Bluetooth function on your mobile device, select the “TWS” from the list of available Bluetooth devices Click it to pairing, once the earphone is paired with a mobile device, you will hear a beep tone and the led indicator will off.

Previous track: Short Press(Touch) the MF button of the Left Earphone twice.
Next track: Short Press(Touch) the MF button of the Right Earphone twice.
Increase Volume: Short Press(Touch) the MF button of the Right Earphone 3 times.
Decrease Volume: Short Press(Touch) the MF button of the Left Earphone 3 times.
Pause/Play Music: Short Touch of the MF button of either Earphone will Pause/Resume the music.

ANSWER/ END/ REJECT A CALL

Answer an incoming call: Short Press(Touch) the MF button of either earphone.
Reject Incoming Call Press(Touch) the MF button of either earphone for 2 seconds and release.
End a call Short Press(Touch) the MF button of either earphone after a phone conversation

VOICE ASSISTANT:

Activated the voice assistant: Short Press(Touch) around 1 5 seconds of either earphone to activate the SIRI voice assistant function, only MS system supported.

Close the voice assistant: After activated, short Press(Touch) for around 15 seconds of either earphone to close the SIRI voice assistant function, only the IOS system supported

Put the Bluetooth Earphone back into the charging slots correctly and securely to charging

ATTENTION

  1. Please kindly read this user manual before using the product carefully, and keep it for future reference.
  2. Please charge the product battery fully when first used.
  3. If do not use the product exceed 2 weeks, please charge it.

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals