Joysticks HS04-1 Wireless Controller User Guide

: June 5, 2024
: JOYSTICKS

Table of Contents

Joysticks HS04-1 Wireless Controller
Button Layout
Speciﬁcations
Button Assign Function
LED Ring Setting
Gyro Calibration
Charging Instructions
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Joysticks HS04-1 Wireless Controller

Button Layout

button
Left stick
Directional pad
Screenshot button
Y button
button
X button
button
Right stick
Home button
M button
Turbo button
3L button
M button
Reset button
Turbo button
R button
L button
ZL button
SL button
Pairing button
SR button
Type-C
interface
ZR button
R button
SR button
Pairing button
SL button
Type-C interface

Speciﬁcations

Transmission Media: Bluetooth 2.1
Carrier Wave: 2.402-2.480GHz
Protocol: Bluetooth 2.1
LED: 8 LED Lights & 8 Multi-Color LED lights
Battery: One Lithium polymer battery、3.7V 500/mAH
Battery life: 3-4 hours after fully charged
operating voltage: 3.7V-4.2V
charging voltage: 5V
Operating temperature: -10℃~50℃
storage temperature: -20℃~70℃
Dimensions (approx): 72041mm
weight(approx): 149g

Connection
Conventional Connection

Attaching the controllers to the console will connect them automatically.
The Joy-Con controllers will remain paired when you detach them from the console, and you’ll be able to use them wirelessly.

Bluetooth Reconnecting
Press the Home button or the Capture button to reconnect your controllers back to the console, 4 LED indicators on the side will start to ﬂash in a regular pattern as an indication of reconnecting.

Turbo Function
Note:
The T button on the left controller can only assign the buttons that are on the left controller. Same goes for the T button on the right controller.

Turbo Mode
Hold down the T button and then press the button that you want to set for the 1st time to turn on the normal turbo function. (Controller will vibrate.) Hold down the T button and then press the button that you want to set for the 2nd time to turn on the automatic turbo function. (Controller will vibrate.)

Turn Oﬀ
Hold down the T button and then press the button that you have set for the 3rd time to turn oﬀ its turbo function. (Controller will vibrate.) Hold the T button for 5 seconds to cancel the Turbo function of all buttons.

Turbo Speed Adjustment
A total of 3 turbo speeds can be adjusted cyclically.Hold down the T button and press the ‒ button for Controller(L). (Controller will vibrate.)Hold down the T button and press the + button for Controller(R). (Controller will vibrate.)

Buttons can be set
Left controller： L / ZL / 3L button and Control Pad (Up / Down/ Left/ Right). Right controller： R / ZR / 3R button and A / B / X / Y button.

Button Assign Function

Note:
The M button on the left controller can only assign the buttons that are on the left controller. Same goes for the M button on the right controller.

Assign Setting
Hold down the M button and press the button you want to assign to the 3L button for Controller(L). (Controller will vibrate.) Hold down the M button and press the button you want to assign to the 3R button for Controller(R). (Controller will vibrate.)The above steps can directly change the button to be set

Turn Oﬀ
Hold the M button for 5 seconds to cancel the assaign function of the controller.(Controller will vibrate.)

Buttons can be set
Left controller： L / ZL / Left stick button and Control Pad (Up / Down/ Left/ Right). Right controller： R / ZR / Right stick button and A / B / X / Y button.

Vibration Level Adjustment
Press the T button and push the Joystick up or down to adjust the vibration level of each controller.(Controller will vibrate when adjusting between each vibration level.) There are 5 levels of Vibration：100%，75%，50% ，30%，0%. (Default level is 50%)

LED Ring Setting

Normal Mode
Hold the T button and press the joystick once to turn the light into normal mode（the light will keep on this color）， and repeat this procedure to change color.（Controller will vibrate when set successfully)
1-8 colors: 1.Red 2. Orange 3. Yellow 4. Green 5. Cyan 6.Blue 7. Purple 8.Rainbow

Brightness Adjustment
Press & hold the T button and joystick to change the brightness, then release the joystick to ﬁx the brightness. （Controller will vibrate when set successfully)

Breathing Light Mode
Hold the T button and press the joystick twice to turn the light into breathing light mode, the following three modes will be cycled.

Gyro Calibration

First, press and hold the Pairing Button to turn oﬀ the controller.
For controller(L), press the L , UP and the Capture button together to enter the calibration mode. For controller(R), press the R , X and the Home button together to enter the calibration mode.
When entering the calibration mode, LED lights will ﬂash alternately. Then align the controllers with the rails on either side of the console, and slide them down BUT DO NOT slide them to the bottom of the rail. (If you hear a click you need to press the release button and slide them up a little.)
Then press the – button for controller(L) and + button for the control(R) to start the calibrating. Controllers will be reconnected back to the console when calibration is over.

Reset Button Function
When there are some unsolvable faults in the controller, you can try to press and hold the reset button on the back of the controller for more than 5 seconds. At this time, the controller is powered oﬀ and reset, and you need to reconnect according to the method of connecting the controller for the ﬁrst time.

Driver Package
We support downloading the driver package through a USB connection to the computer to ﬁx some problems that may be encountered in use. If the driver package does not work, please contact us by email (support@binbok.com). Driver package download website: www.binbok.com

Note：
No need to download driver if it can be used normally, otherwise new problems may occur due to version conﬂicts)

Low Voltage Alarm

If the lithium battery voltage is lower than 3.45V±0.1V, the current channel tight ﬂashes quickly and indicate low voltage.
If the lithium battery voltage is lower than 3.35V±0.1V, it will automatically sleep.

Charging Instructions

When the controllers are in the USB charging state, LED lights will ﬂash slowly, if connected to the console, the lights will stay on when it is fully charged; If not, the light will be oﬀ.
When the pairing indication conﬂicts with the charging low power indicator, the pairing indicates a concern.

Warning

Do not expose the controller to high temperature, high humidity or direct sunshine.
Do not allow liquid or small particles to enter the controller.
Do not put any heavy object on the controller.
Do not disassemble the controller.
Do not twist or pull the cable too strongly.
Do not throw, drop, or apply strong shock to the controller.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be u sed in portable exposure conditions without restriction.