CADMOS CR2032 Colorful Light Alarm Clock User Manual

June 14, 2024
CADMOS

User Manual
Colorful Light Alarm Clock

CADMOS CR2032 Colorful Light Alarm Clock -

Read and follow all instructions in this user manual before use.
Notice:
The CR2032 batteries only save the time of day and the programmed wake time. All functions are only possible with mains power operation.

Product Introduction

CADMOS CR2032 Colorful Light Alarm Clock - Product
Introduction

  1. Alarm 1 ON/OFF button / Alarm 1 Setting
  2. Time Setting/Fall Asleep Function
  3. Reduce Light Intensity / Setting Reduce
  4. Snooze / Light ON/OFF / Light Mode Change
  5. Increase Light Intensity/Setting Increase
  6. Music sound ON/OFF & Music Shift
  7. Alarm 2 ON/OFF button / Alarm 2 Setting
  8. Volume Setting
  9. Time Brightness Setting
  10. USB output charging port
  11. Type-C input power port

Setting and Maintenance

First Use:
Connect the Type-C cable to the alarm clock connected to the power jack of the device and the other end of the USB cable to the USB female socket.As shown in Chart 1.

Install Battery:
CR2032 battery is pre-installed with device, please remove the insulating sticker from the back side for normal use as in Chart 2.

Storage:
Alarm Clock should be placed into the carton or stored at a cool and dry place.

Cleaning:
Wipe dust off with a soft and damp cloth. Please do NOT use liquid or abrasive cleaners.

CADMOS CR2032 Colorful Light Alarm Clock - Setting and
Maintenance

Time Display Setting

CADMOS CR2032 Colorful Light Alarm Clock - Icon 1

The default clock time is AM 12:00 for the first time with power.
Notice: The following operation should be operated step by step.

  1. Hour Time Setting
    Press and hold the button  for 3 seconds until hour indicator is blinking, then press the button to change hour. Press the button  to confirm hour, then the minute indicator is blinking.

  2. Minute Time Setting
    Press the button to change minute when the minute indicator is blinking, then press the button  to confirm minute and the 12-hour(AM/PM) or 24-hour clock mode indicator is blinking.

  3. Adjust 12-hour(AM/PM) or 24-hour mode
    Press the button to choose between12-hour (AM/PM) and 24-hour clock modes when the mode number indicator is blinking, then press the button  to confirm the mode and the MON-SUN indicator is blinking.

  4. MON-SUN Setting
    Press the button to choose a day from MON-SUN after the indicator is blinking, then press the button  to complete all the time setting.

Alarm ON/OFF

Prerequisite: The time display is ON
Press the button of alarm 1 or press the button of alarm 2 to switch the alarm ON/OFF.
The corresponding icon appears on the display when the alarm is ON and the icon will disappear when the alarm is OFF.

Notice:
The operation modes of alarm 1 and alarm 2 are exactly following with the same procedure.

Alarm Setting (as Alarm 1)

Notice: The following operation should be operated step by step.

  1. Alarm Hour Time setting
    Press and hold the button for 3 seconds and the hour indicator is blinking.
    Then press the button to change hour.
    Press the button again to confirm alarm hour and the minute indicator is blinking.

  2. Alarm Minute Time Setting
    Press the button to change minute when the minute indicator is blinking.
    Then press the button to confirm alarm minute and the wake-up sound indicator (S01-S07) is blinking.

  3. Wake-up Sound Setting
    Press the button to choose a wake-up sound from S01 to S07 when the sound indicator is blinking.
    Then press the button to confirm sound and the alarm volume indicator(V01-V16) is blinking.

  4. Alarm Volume Setting
    Press the button to adjust the volume from V01 to V16 when the volume indicator is blinking.
    Then press the button to confirm the volume and Everyday / Weekday / Weekend indicator is blinking.

  5. Every Day/weekday/weekend alarm setting
    Then press the button to choose Everyday / Weekday / Weekend modes.

  6. Press the button to confirm and complete setting of alarm 1

Snooze Function

The alarm sound will be played at the set time after alarm activated. You could follow with below instruction to operate:

  1. Snooze Function
    Press the button to snooze mode and stop the sound. It will be played again in automatically after 9 minutes. (Use Tip: The times of snoozer is unlimited)

  2. Manually stop the alarm clock
    Press the alarm 1 or alarm 2 if you want to turn off the current alarm sound when the alarm is played or snoozed and the alarm is still ON by the following times.

  3. Automatically stop the alarm clock
    The current alarm sound will be stopped in automatically after 20 minutes if no any operations done.

Note:

  1. The alarm icon flashes on the display when the alarm is snoozed
  2. The alarm icon stays bright on the display, which means alarm activated

Relaxing Bedtime Sound Function

  1. Switching ON/OFF the relaxing bedtime sound function
    Press the button to switch ON the relaxing bedtime sound function, then continue click the button to change sounds from S01-S08 until OFF, or press and hold the button for 3 seconds to turn OFF the sound.

  2. Sound Volume setting
    Rotate the wheel on the left side of the device to set the volume of sound.

Colorful Light Modes

  1. Light ON/OFF
    Press the button to switch ON the light and press and hold the button for 3 seconds to switch OFF the light.

  2. Light Mode Changing
    Press the button to change the light modes from C01 to C08 when the light is ON.

  3. Light Intensity Adjusting
    press the button to adjust the light intensity from L01.

Time Display Intensity Setting

Rotate the wheel of DIMMER on the left side of the device to adjust the time display intensity.

Relaxing Bedtime Sound Function

  1. Countdown ON/OFF
    Press the button to turn ON time countdown, then the time indicator will blinding for 5 seconds. Click to change the set of countdown time within 5 seconds and it could be set between 10 and 120 minutes. It will be confirmed after 5 seconds without any operation. Press and hold the button  for 3 seconds to turn OFF.

  2. Time Countdown to Fall Asleep
    You can turn ON/OFF and change the sound and light mode when the time countdown is ON. The sound and light will be turned OFF with time countdown.

  3. Time Countdown Review
    Click to review the left time of countdown when the function is ON.

Change Battery

  1. Remove the screw from the battery case with a screwdriver
  2. Take off the cove of battery case
  3. Insert the battery into the case while the positive electrode is upward
  4. Put the cover of battery case into the slot
  5. Tighten the battery case with the bolt

CADMOS CR2032 Colorful Light Alarm Clock - Change
Battery

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals