KONOVA KMS-53 Wireless Motorized Camera Slider System Instruction Manual
- June 5, 2024
- KONOVA
Table of Contents
KMS-53 Wireless Motorized Camera Slider System
Instruction Manual
QR CODE
|
---|---
https://itunes.apple.com/cn/app/id1489078486?mt=8|
http://alligo.co.kr/qrcode/kmss3_android.html
Including
- Motor module
- Motor mount adapter
- Belt block (2pcs)
- Hex wrench and bolts
- Belt
- Micro USB 5 pin power cable
- Shutter release cable
- Carry Bag
Please know that 2 (Motor mount adapter) and 3 (Belt blocks) are not used for P1 carbon sliders. So we have removed them it you order the KMS-S3 with P1 carbon slider.
Setup: P1 SLIDER
-
Insert the bolt and tighten with two knobs.
-
BMount the belt on the pulley and bearings.
-
count the motor on the camera plate of the slider.
-
Pull the belt tightly and fasten the belt block.
Setup: Belt block
Step-1 Insert the ‘Belt
block’ to the end of the slider with the bolts facing up and lock the red
knob.
Step-2 With the flat
surface of the belt facing up, insert the belt in the Block inset, place the
belt to the slider closely and tighten the bolts.
Setup: Motor mount
Step-1 With the marked
side facing down, attach `Motor mount adapter’ to the slider.
Step-2 Tighten with the
bolt included in the box. One more extra bolt is a spare one.
Setup: Motor module attach
Step-1 Place the belt
to the ‘Belt pulley’ and bearings like the picture above.
Step-2 Attach the ‘Motor
module’ to the ‘Motor mount adapter’ like the picture above.
Setup: Power supply
Use-1 It is compatible with Sony Np-750 or 970 battery.
Use-1 It is also
compatible with the power bank of a mobile phone.
How to operate
Bluetooth Searching : Find a Bluetooth
Language: Select languages
Length : Select Linear Measure (mm) or US Unit (in)
Touch “ Bluetooth
Searching ” and select the correct Bluetooth device.
Attention: if you use KMS-S3 with the KONOVA Pan Head module, please only
select the Bluetooth name “KMS-Slider”.
KONOVA Pan head module is not included in KMS-S3.
AB setting mode
Setpoint A and B :
Touch the Left, right buttons to set A and B points for the slider, up and
down buttons are for Pan’s head
Remaining battery for the motor module
Remaining battery for the pan head module
Attention: KONOVA Pan head module is not included in KMS-S3.
Video mode
Multi-shot motion
It can add more than 6 new motions for this function.
Press and it shows below| Set A (start point), B (endpoint), and duration time
for each new motion.
Timelapse mode
Exposure : input a higher value than your camera exposure time
Duration : duration time of the total timelapse period
Interval : set interval waiting time between each shooting
Frames : set the total shooting frames you need
FPS : shows what FPS for your timelapse video, you can select 24, 25 or
30.
Video time: calculates the playtime for the timelapse video.
For example, the total frames are 300 cuts, if you do a timelapse video for 24
fps, the total playtime for the video should be 12.5 seconds. The “Video time”
will show 12.5 S.
Delay : set a delay waiting time before the first shooting starts
360° Mode
360° Mode is only for the KONOVA Pan Head module.
Exposure: input a higher value than your camera exposure time
Angle: the angle of panning
Frames: set the total shooting frames you need
Duration: duration time of the total shooting period
Manual mode
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
KONOVA INC.
www.konovaphoto.com
44-9, Techno 10-ro, Yuseong-gu, Daejeon, South Korea
Tel. -F1 213-341-1618, +82 70-7865-2668
• Fax. +82 2-6280-8560
E-mail. info@konovaphoto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>