Shenzhen Chaojin Electronics CJ-501 Bluetooth Aroma Diffuser User Manual

AROMA DIFFUSER USER MANUAL

This Aroma Diffuser uses Ultrasonic waves to instantly vaporize water and essential oil in the tank, to produce a cool, dry fragrant mist.

1. LED indicator of time setting
2. LED indicator of PM when 12 hours mode
3. LED indicator of alarm setting
4. LED indicator of alarm on

TO SET UP DIFFUSER

1. Remove lid and set aside.
2. Place on a flat surface.
3. Fill diffuser with water up to carved max line.
4. Add 3-4 drops of essential oil. Add more if desired.
5. Replace lid.
6. Plug unit to power outlet.
7. Press the MIST button to start.

TO ADJUST THE MIST TIMER

1. Press “MIST “ to adjust from ON-1H-3H-5H-OFF.

TO ADJUST LIGHT

1. Press “ Light” to turn on the LEDS.
2. Press again to adjust from 7 changing colors-1 fixed color-off.

TO PLAY MUSIC

1. Hold “Play” for 2 seconds to switch on /off the blue-tooth function.
2. Place Bluetooth TM device within 3 feet of the speaker.
3. Search for available devices and select “Clock diffuser”.
4. Play your favorite tunes and press “Play” to pause or continue the tunes.
5. Press “+” or ”-” to shift the tunes.
6. Hold “+” or ”-” to for 2 seconds to adjust the volume.

TO SET CLOCK

1. Hold “Mist” until 12/24 appears on the screen. when ② is lighted, it displays to be PM time of 12hr clock
2. Press “+” or ”-” to select between 12hr/24hr clock.
3. Press “Mist” to until the digital number flickers.
4. Press “+” or ”-” to adjust the hour step by step / Hold “+” or ”-” for fast switching.
5. Press Mist to confirm.
6. Press “+” or ”-” to adjust the minutes step by step Hold “+” or ”-” for fast switching.
7. Press “Mist” to finish the clock setting.
   (NOTE: Press “Light” in time setting mode will return to the initial state “00:00”.)

TO SET ALARM

1. Hold “Light” for 2 seconds to enter into the alarm setting.
2. Press “+” or ”-” to adjust the hour step by step / Hold “+” or ”-” for fast switching.
3. Press “Light” to confirm.
4. Press “+” or ”-” to adjust the minutes step by step / Hold “+” or ”-” for fast switching.
5. Press “Light” to finish the alarm setting.
6. when ④ is lighted, an alarm is on
   (Note: When an alarm is ringing, press any button to turn off the alarm.)

TO CANCEL ALARM

1. Hold “Light” for 2 seconds to enter into the alarm setting.
2. Press “Mist” to cancel the alarm and “- – – -” appears.
3. Press “Light” to finish alarm cancelation.

SPECIFICATIONS

MAINTENANCE INFORMATION

In order to ensure product safety and the efficiency of your diffuser, it is recommended to undertake maintenance clean after every 5-6 uses.

1. Unplug the power cord from the power socket and the base of your diffuser.

2. Remove the cover.

3. Carefully empty any remaining water from the diffuser. To avoid water. entering the device, do not tilt to the side where the air outlet is (where the mist comes out).
   NOTE: Do not touch the ultrasonic board at the center of the water tank. In case of maintenance where it needs to be cleaned, please use cotton swabs.

4. Using a damp cloth previously soaked in water diluted with dish detergent, wipe down the body.

5. Re-fill the diffuser with plain water and let it mist for 30 minutes to clean out any excess oils. Carefully drain after use.

6. If any essential oils have dropped on the outside of the water tank, wipe it down with a damp cloth.

7. Place the cover back on the diffuser.
   NOTE: Do not use chemicals such as benzine thinner, alcohol hydrochloric detergents, or enzyme detergents. May cause damage to the device and emit poisonous gases. Only use neutral detergents.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic
Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>