OLIGHT Perun Right-angle light User Manual

OLIGHT Perun Right-angle light

IN THE BOX

SPECIFICATION

All performance measurements in accordance with ANSI/NEMA FL1-2009 standards.The tests are performed using the battery included in the flashlight, and is measured indoors under a room temperature of 25 degrees Celsius with windless conditions. The runtime of turbo and high modes may vary depending on the external temperature and ventilation conditions, these biases may affect the results of testing.

SUPPORTED BATTERY

• The light is equipped with a customized 18650 rechargeable battery. In case of emergency, other brand’s 18650 battery with built-in protection board can be used (but charging and advertised outputs are not supported).
• DISCLAIMER: 2 x RCR123 batteries can NOT be used in this product, otherwise it may damage the electronic components.
• Low Battery Warning: The light will vibrate once every 30 seconds when the battery power is less than 10%, except for the moonlight mode.

PRODUCT OVERVIEW

BEFORE FIRST USE

Remove the protective film from the lens, unscrew the body and remove the yellow insulating film.

CHARGING

• Connect the magnetic USB end of the charging cable to an external USB power source, then attach the other end of the magnetic charging cable to the charging port. It takes no more than 3.5 hours to fully charge the light ( For reference only. When the USB power supply is insufficient to provide 5V 2A power capacity, the charging time will be longer ).
• Before first use please fully charge the product.
• Only charge with standard USB magnetic charging cable, not compatiable with other USB magnetic charging cable.

LANYARD ATTACHMENT

Put the pin tool through the light lanyard hole and then hook the lanyard to the hole.

PROXIMITY PROTECTION FUNCTION

When the infrared distance sensor detects an obstruction nearby, the brightness will automatically reduce to the lowest level (30 lumens). The light will shut down directly if the blockage continues for more than 60 seconds. The sensor is sensitive to occlusion only (the sensing distance will be different due to different colors and materials).

ATTENTION:

1. Please keep the surface of the lens clean. Stains or water mist will affect the performance of the built-in sensor located in the black area, resulting in the failure of high mode (only works at low mode), please erase in time.
2. Pay attention to protect the lens from scratches. Scratches on the surface of the lens will reduce the luminous flux. In severe cases, it will affect the internal sensor performance, resulting in the failure of high mode (only works at low mode).

OPTIONAL ACCESSORY

HOW TO TURN IT INTO A HEADLAMP

1.  Remove the pocket clip.
   

2.  Place the product in the center of the light mount

3. Pull the end of the silicone wrap to fasten the product
   

HOW TO REPLACE THE MAGNET WITH AN EVA PAD

1. Pull the head strap open in the section as shown below

2. Rip off the EVA pad

3. Take out the magnet inside

4. Put the small replacement EVA pad in its place
   

5. Use the large adhesive EVA pad to seal it
   

HOW TO OPERATE

ON/OFF:
When the light is not locked out, single click switch to turn on/off.

CHANGE BRIGHTNESS LEVEL:
When the light is on, press and hold the side switch to cycle through the mode sequence moonlight (or turbo, SOS) – low – medium – high – low. The mode is selected when the switch is released.

MOONLIGHT MODE:
When the light is off or in standby mode, press and hold the switch for over one second to access the moonlight mode.

DIRECT ACCESS TO TURBO:
Enter and exit Turbo mode: quickly double click the side switch to enter Turbo mode, and quickly double-click the side switch again to exit Turbo mode.When the memorized mode is on high, quickly double-click the side switch to exit Turbo mode and switch to medium mode. When the memorized mode is Medium, Low, or Moonlight, quickly double click the side switch to exit turbo mode and switch to the previously memorized mode.

SOS:
Quickly triple click the side switch to access the SOS mode.
TIMER: The Perun has a long (9 minutes) and short (3 minutes) timer when the light needs to be automatically turned off. When the flashlight is on, double click and hold the side switch under the current brightness level to access the timer settings. A single blink accesses the short timer while two blinks accesses the long timer. The flashlight will automatically turn off when the timer is up. After the timer is set, double click and hold the side switch to shift the timer settings. When the timer is up and the user is about to enter the timer again, the light will return to the last timer setting.

LOCKOUT:
When the light is off, press and hold the side switch for two seconds to access the button lockout mode. Under the lockout mode, press and hold the switch for less than two seconds without releasing it and the light will enter the moonlight mode again. The light will quit the moonlight mode once the switch is released and it will return to and stay at the button lockout mode.

BUTTON UNLOCK:
Press and hold the side switch for about two seconds until the light gives a single blink and then release the switch. The light will unlock and will return to the moonlight mode.

DANGER

•  Do NOT throw the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
•  The battery can only be charged while installed in the flashlight. When charging, please use the provided charger for your light.

WARNING

•  Keep out of reach of children.
•  If the light is about to be put aside for a long time or be transported, please unscrew the body for half a circle to cut off the circuit.
•  Do not use the turbo mode continuously when the environmental temperature is high in case the light body is too hot to hold.
• Ensure the battery is inserted with the negative ( – ) end pointing to the head of the light ( LED side ).
• Store the battery with care; if the battery needs to be changed, please take good care of the battery taken out. Do not mix it with the conductive metals.

NOTICE

• Moonlight and turbo mode are not the normal brightness levels ( low, medium, and high mode ). Under moonlight and turbo mode, press and hold the switch to enter the normal brightness level cycle.
• When the light is turned on, the light will return to the last used setting. Only moonlight, low, medium, and high mode can be memorized when the light is turned off. If the light is turned off on turbo mode, it will memorize high mode and will revert to the medium setting after 10 minutes. SOS mode cannot be memorized.
•  When the battery capacity is less than 60%, the internal MCU will automatically shield the turbo mode and reset high mode to the highest brightness level.
• Active thermal management: On turbo mode, overheating can be avoided by adjusting the power output.

WARRANTY

Within 30 days of purchase: Contact the original seller for repair or replacement.
Within 5 years of purchase: Contact Olight for repair or replacement.
Battery Warranty: Olight offers a one year warranty for all rechargeable batteries. This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.

References

• Olight | Illuminate Your World.
• Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>