JASCO ZW7105 60W Equivalent Smart LED Bulb Instruction Manual
- June 5, 2024
- JASCO
Table of Contents
JASCO ZW7105 60W Equivalent Smart LED Bulb
Z-WAVE INTEROPERABILITY
This product can be added and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All nonbattery-operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This device supports Lifeline (association group 1) supporting 5 nodes for lifeline communication. Group 1 must be assigned the node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the “Device Reset Locally” function. Refer to the instructions of your controller for any available details on how this can be set.
HOW TO USE
- Getting to know your new Z-Wave device
- Brightness: 750 lumens (equivalent to 60W incandescent bulb) Power consumption: 9W Color temperature: 2700K
- Replaces A19 light bulbs
- Remote ON/OFF and brightness control via the Z-Wave controller
- This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
- Turn off power to the light bulb socket where the installation will occur
- Screw the smart LED bulb into the socket.
- Adding your device to a Z-Wave network
- When initially powered, the bulb is in SmartStart inclusion mode. If your hub supports SmartStart, scan the QR code.
- To change to classic inclusion mode, turn bulb OFF, then ON three times. The bulb rapidly flashes four times to indicate classic mode.
- To change back to SmartStart inclusion mode, turn the bulb OFF, then ON three times. The bulb rapidly flashes six times to indicate SmartStart mode. NOTE: The bulb attempts to connect in either inclusion mode for 10 seconds. If not found after 10 seconds, cycle the bulb OFF/ON to restart the inclusion mode.
- In either method, the bulb flashes twice to indicate it was added to the network.
- NOTE: The bulb remains in the last known inclusion mode when cycled OFF/ON once. You have complete control to turn your light ON/OFF or set dim levels according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can control your lighting from your mobile devices. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit pin code. Figure 1.
- NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity
IMPORTANT!
It is extremely important to follow the below practice or use ONLY your
preferred wireless remote-control device to turn ON/OFF the smart bulb.
Without power to the light bulb, the smart bulb cannot be turned ON remotely
or function as a signal repeater to maintain proper Z-Wave network. To avoid
accidently turning OFF the power to the smart bulb, install the optional clear
switch cover (included).
This switch lock prevents you from accidently cutting power to your smart bulb. Without power to the smart bulb, it cannot be turn on remotely. Designed for rocker-style and toggle switches.
To remove and reset the device
1. Follow the instructions for your Z-Wave certified controller to remove a
device from the Z-Wave network.
2. Once the controller is ready to remove your device, turn ON the light
switch. The smart bulb flashes twice when removed from the network.
To return your smart bulb to factory defaults
Starting with the bulb on, cycle the wall switch OFF/ON four times.
- Turn the switch off, pause one second, then turn back ON.
- Repeat three times (four times total).
- The smart bulb flashes twice when reset.
- NOTE: This should only be used in the event your network’s primary controller is missing or otherwise inoperable.
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1,
Monday–Friday, 7AM–8PM Central Time. For the most up-to-date product support,
accessories, electronic (PDF) format manuals and more, visit
www.byjasco.com/support.
WARNING
- NOT FOR EMERGENCY LIGHTING
- RISK OF ELECTRIC SHOCK
- RISK OF FIRE
- RISK OF BURNS
- USE IN DRY LOCATIONS ONLY
- ONLY USE THE CONTROL PROVIDED WITH OR SPECIFIED BY THESE INSTRUCTIONS TO CONTROL THIS LAMP. THIS LAMP WILL NOT OPERATE PROPERLY WHEN CONNECTED TO A STANDARD (INCANDESCENT) DIMMER OR DIMMING CONTROL
- NOT FOR USE IN TOTALLY ENCLOSED LUMINARIES
- DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENTS
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of allother warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM – 8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period.
Purchase additional items at ezzwave.com or visit your
local retailer.
SPECIFICATIONS
- Power: 120VAC, 60Hz, 9W
- Signal (frequency): 908.4/916MHz
- Z-Wave range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
- Operating temperature range: 32-104° F (0-40° C)
- For indoor use only
- Specifications subject to change without notice due to continuing product improvement
FCC RULES
This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions:
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.