Nice FGPB-101 Universal Wireless Button Instruction Manual
- June 5, 2024
- Nice
Table of Contents
- Nice FGPB-101 Universal Wireless Button
- WARNINGS AND GENERAL PRECAUTIONS
- PRODUCT DESCRIPTION
- BASIC ACTIVATION
- ADDING THE DEVICE
- REMOVING THE DEVICE
- OPERATING THE DEVICE
- ASSOCIATIONS
- ADVANCED PARAMETERS
- TECHNICAL SPECIFICATIONS
- PRODUCT DISPOSAL
- DECLARATION OF CONFORMITY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Nice FGPB-101 Universal Wireless Button
WARNINGS AND GENERAL PRECAUTIONS
- CAUTION! – This manual contains important instructions and warnings for personal safety. Carefully read all parts of this manual. If in doubt, suspend installation immediately and contact Nice Technical Assistance.
- CAUTION! – Important instructions: keep this manual in a safe place to enable future product maintenance and disposal pro-cedures.
- CAUTION! – Any use other than that specified herein or in environmental conditions other than those stated in this manual is to be considered improper and is strictly forbidden!
- The product’s packaging materials must be disposed of in full compliance with local regulations.
- Never apply modifications to any part of the device. Operations other than those specified may only cause malfunctions. The manufacturer declines all liability for damage caused by makeshift modifications to the product.
- Do not expose this product to moisture, water or other liquids.
- This product is designed for indoor use only. Do not use outside!
- This product is not a toy. Keep away from children and animals!
- If the battery is leaking and the contained material is ingested, rinse mouth and surrounding area with clear water. Seek medical attention right away.
PRODUCT DESCRIPTION
Push-Control is a compact, battery-powered, Z-Wave Plus™ compatible device. It
allows you to control devices through the Z-Wave network and run various
scenes defined in Yubii smart home system.
Different actions may be triggered with one to five clicks or by holding the
button down. In panic mode, each press of the button results in trig-gering
the alarm defined in the Z-Wave controller.
Due to its small design and wireless communication, Push-Control can be
conveniently mounted on any surface and in any position or location at home,
e.g. beside the bed or under the desk.
Main features
- Compatible with any Z-Wave™ or Z-Wave Plus™ Controller
- Supports Z-Wave network Security Mode with AES-128 encryption
- Completely wireless with battery power and Z-Wave communication
- May be installed anywhere in your home
- Extremely easy installation – simply add and put on desired surface
- Available in three distinctive colors: white, black, and red
Push-Control is a fully compatible Z-Wave Plus™ device.
This device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers. All non-battery operated devices within the network will act as repeaters to increase the reliability of the network. The device is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave Controller must be used in order to fully utilize the product.
BASIC ACTIVATION
- Press and turn the button counter-clockwise to open the casing.
- Remove the paper strip underneath the battery.
- Press and turn the button clockwise to close the casing.
- Place the device within the direct range of your Z-Wave controller.
- Set the main controller in (security/non-security) add mode (see the controller’s manual).
- Click the button 6 times at least.
- Wait for the device to be added into the system, successful adding will be confirmed by the controller.
- Install the device in desired location using the attached self-adhesive pad.
- Click the button 4 times to wake it up.
ADDING THE DEVICE
- Adding in security mode must be performed up to 2 meters from the controller.
- In case of problems with adding the device, please reset the device and repeat the adding procedure.
Adding (Inclusion) – Z-Wave device learning mode, allowing to add the device to existing Z-Wave network. To add the device to the Z-Wave network manually:
- Place Push-Control within the direct range of your Z-Wave controller.
- Set the main controller in (Security/non-Security) add mode (see the controller’s manual).
- Click Push-Control at least six times.
- Wait for the adding process to end.
- Successful adding will be confirmed by the Z-Wave controller’s message.
REMOVING THE DEVICE
Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network. To remove the device from the Z-Wave network:
- Place Push-Control within the direct range of your Z-Wave controller.
- Set the main controller in remove mode (see the controller’s manual).
- Click Push-Control at least six times.
- Wait for the removing process to end.
- Successful removing will be confirmed by the Z-Wave controller’s message.
Note. Removing the device from the Z-Wave network restores all the default parameters of the device.
OPERATING THE DEVICE
Operating the button
Depending on how and how many times Push-Control is pressed, it will perform a
different action.
Table A1 – Responses to button actions
Action| Response
1 click| send action to associated devices (switch on/off by default) and/or
trigger a scene
2 clicks| send action to associated devices (switch on maximum level by
default) and/or trigger a scene
3 clicks| send action to associated devices (no action by default) and/or
trigger a scene
4 clicks| wake the device up and/or trigger a scene
5 clicks| start reset procedure (press and hold for 5s to confirm) and/or
trigger a scene
6 or more clicks| learning mode (adding/removing)
Hold| send action to associated devices (start level change up/down) and/or
trigger a scene
Release| send action to associated devices (stop level change) and/or trigger
a scene
Note. If notifications are enabled, each press of the button results in
sending a command (Notification Type=HOME_SECURITY,
Event=Intrusion, Unknown Location).
Waking up the device
Push-Control needs to be woken up to receive information about the new
configuration from the controller, like parameters and associations. Click
Push-Control 4 times to wake it up.
Scene ID
Every action with Push-Control is send to the main controller with Scene ID
equal to 1. Controller recognizes type of action using the attribute assigned
to it.
Table A2 – Scene ID attributes sent
Action| Attribute
1 click| Key Pressed 1 time
2 clicks| Key Pressed 2 times
3 clicks| Key Pressed 3 times
4 clicks| Key Pressed 4 times
5 clicks| Key Pressed 5 times
Hold| Key Held Down
Release| Key Released
Reset procedure of Push-Control
Reset procedure allows to restore the device back to its factory settings,
which means all information about the Z-Wave controller and user configuration
will be deleted. In order to reset the device:
- Click Push-Control exactly five times.
- Press and hold Push-Control for at least 5 seconds.
Note. Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing.
ASSOCIATIONS
Association (linking devices)
direct control of other devices within the Z-Wave system network e.g. Dimmer,
Relay Switch, Roller Shutter or scene (may be controlled only through a Z-Wave
controller).
Association allows direct transfer of control commands between devices, is
performed without participation of the main controller and re-quires
associated device to be in direct range.
The device supports the generic Z-Wave command class “Basic” but will ignore
any SET or GET commands and will not respond with a Basic Report.
Push-Control provides the association of four groups:
- 1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).
- 2nd association group – “On/Off” is assigned to clicking the button and is used to turn on/off associated devices.
- 3rd association group – “Dimmer” is assigned to holding the button and is used to change level of associated devices.
- 4th association group – “Alarm“ is assigned to clicking and/or holding the button (triggers are defined in parameter 30) and is used to send alarm frames to associated devices.
Push-Control in 2nd, 3rd and 4th group allows to control 5 regular or
multichannel devices per an association group, with the exception of
“Lifeline” that is reserved solely for the controller and hence only 1 node
can be assigned.
It is not recommended to associate more than 10 devices in general, as the
response time to control commands depends on the number of associated devices.
In extreme cases, system response may be delayed.
ADVANCED PARAMETERS
The device allows customizing its operation to user’s needs using configurable
parameters.
The settings can be adjusted via Z-Wave controller to which the device is
added. The way of adjusting them might differ depending on the controller.
Wake up interval
Push-Control will wake up at each defined time interval and always try to
connect with the main controller. After successful communication attempt, the
device will update configuration parameters, associations and settings and
then will go into Z-Wave communication standby.
After failed communication attempt (eg. no Z-Wave range) the device will go
into Z-Wave communication standby and retry to establish con-nection with the
main controller after the next time interval. Setting wake up interval to 0
disables sending Wake Up notification to the controller automatically. Wake up
may be still performed manually by clicking Push-Control 4 times.
- Available settings: 0 or 3600-64800 (in seconds, 1h – 18h)
- Default setting: 0
Note. A longer time interval means less frequent communication and thus longer battery life.
Table A3 – Push-Control – Available parameters
Parameter:| 1. Scenes sent to the controller
Description:| This parameter determines which actions result in sending scene
IDs and attributes assigned to them.
Values of parameter 1 may be combined, e.g. 1+2=3 means that scenes will be sent after pressing the button
once or twice.
Available settings:| 1 – Key Pressed 1 time
2 – Key Pressed 2 times
4 – Key Pressed 3 times
8 – Key Pressed 4 times
16 – Key Pressed 5 times 32 – Key Held Down
64 – Key Released
Default setting:| 127 (all)| Parameter size:| 1 [byte]
Parameter:| 3. Associations in Z-Wave network Security Mode
Description:| This parameter defines how commands are sent in specified
association groups: as secure or non-secure. Pa- rameter is active only in
Z-Wave network Security Mode. It does not apply to 1st „Lifeline” group.
Values of parameter 3 may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure.
Available settings:| 1 – 2nd group sent as secure
2 – 3rd group sent as secure 4 – 4th group sent as secure
Default setting:| 7 (all)| Parameter size:| 1 [byte]
Parameter:| 10. Key Pressed 1 time – command sent to 2nd association group
Description:| This parameter defines commands sent to devices associated in
2nd association group after a single click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 3| Parameter size:| 1 [byte]
Parameter:| 11. Key Pressed 1 time – value of SWITCH ON command sent to 2nd
association group
Description:| This parameter defines value of SWITCH ON command sent to
devices in 2nd association group after a single
click.
Available settings:| 1-255 – sent value
Default setting:| 255| Parameter size:| 2 [bytes]
Parameter:| 12. Key Pressed 2 times – command sent to 2nd association group
Description:| This parameter defines commands sent to devices associated in
2nd association group after a double click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 1| Parameter size:| 1 [byte]
Parameter:| 13. Key Pressed 2 times – value of SWITCH ON command sent to 2nd
association group
---|---
Description:| This parameter defines value of SWITCH ON command sent to
devices in 2nd association group after a double
click.
Available settings:| 1-255 – sent value
Default setting:| 99| Parameter size:| 2 [bytes]
Parameter:| 14. Key Pressed 3 times – command sent to 2nd association group
Description:| This parameter defines commands sent to devices associated in
2nd association group after a triple click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 0| Parameter size:| 1 [byte]
Parameter:| 15. Key Pressed 3 times – value of SWITCH ON command sent to 2nd
association group
Description:| This parameter defines value of SWITCH ON command sent to
devices in 2nd association group after a triple
click.
Available settings:| 1-255 – sent value
Default setting:| 255| Parameter size:| 2 [bytes]
Parameter:| 20. Key Pressed 1 time – command sent to 3rd association group
Description:| This parameter defines commands sent to devices associated in
3rd association group after a single click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 3| Parameter size:| 1 [byte]
Parameter:| 21. Key Pressed 1 time – value of SWITCH ON command sent to 3rd
association group
Description:| This parameter defines value of SWITCH ON command sent to
devices in 3rd association group after a single
click.
Available settings:| 1-255 – sent value
Default setting:| 255| Parameter size:| 2 [bytes]
Parameter:| 22. Key Pressed 2 times – command sent to 3rd association group
Description:| This parameter defines commands sent to devices associated in
3rd association group after a double click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 1| Parameter size:| 1 [byte]
Parameter:| 23. Key Pressed 2 times – value of SWITCH ON command sent to 3rd
association group
Description:| This parameter defines value of SWITCH ON command sent to
devices in 3rd association group after a double
click.
Available settings:| 1-255 – sent value
Default setting:| 99| Parameter size:| 2 [bytes]
Parameter:| 24. Key Pressed 3 times – command sent to 3rd association group
Description:| This parameter defines commands sent to devices associated in
3rd association group after a triple click.
Available settings:| 0 – no action
1 – SWITCH ON
2 – SWITCH OFF
3 – SWITCH ON/OFF – alternately
Default setting:| 0| Parameter size:| 1 [byte]
Parameter:| 25. Key Pressed 3 times – value of SWITCH ON command sent to 3rd
association group
Description:| This parameter defines value of SWITCH ON command sent to
devices in 3rd association group after a triple
click.
Available settings:| 1-255 – sent value
Default setting:| 255| Parameter size:| 2 [bytes]
Parameter:| 29. Key Held Down – command sent to 3rd association group
---|---
Description:| This parameter defines commands sent to devices associated in
3rd association group after holding the button
down.
Available settings:| 0 – no action
1 – START LEVEL CHANGE UP (brightening) 2 – START LEVEL CHANGE DOWN (dimming)
3 – START LEVEL CHANGE UP/DOWN (brightening/dimming) – alternately
Default setting:| 3| Parameter size:| 1 [byte]
Parameter:| 30. Alarm frame triggers
Description:| Parameter determines which actions result in sending alarm
frames to 4th association group.
Values of parameter 30 may be combined, e.g. 1+2=3 means that alarm frames will be sent
after pressing the button once or twice.
Available settings:| 1 – Key Pressed 1 time
2 – Key Pressed 2 times
4 – Key Pressed 3 times
8 – Key Pressed 4 times
16 – Key Pressed 5 times 32 – Key Held Down
64 – Key Released
Default setting:| 127 (all)| Parameter size:| 1 [byte]
Notes:
- Setting parameters 11, 13, 15, 21, 23 and 25 to appropriate value will result in:
- 1-99 – forcing level of associated devices,
- 255 – setting associated devices to the last remembered state or turning them on.
TECHNICAL SPECIFICATIONS
The product Push-Control is produced by Nice S.p.A. (TV). Warnings: – All technical specifications stated in this section refer to an ambient temperature of 20 °C (± 5 °C) – Nice S.p.A. reserves the right to apply modifications to the product at any time when deemed necessary, while maintaining the same functionalities and intended use.
Push-Control
Battery type| ER14250 ½AA 3.6V
Battery life| est. 2 years (with default settings and max. 10 pushes per day)
Operating temperature| 0 – 40°C (32 – 104°F)
Dimensions (diameter x height)| 46 x 34 mm (1.81″ x 1.34″)
- The Radiofrequency of the individual device must be same as your Z-Wave controller. Check the information on the box or consult your dealer if you are not sure.
- Using batteries other than specified may result in an explosion. Dispose of properly, observing environmental protection rules.
- Battery life depends on frequency of usage, number of associations/scenes, Z-Wave routing and network load.
Radio transceiver|
---|---
Radio protocol| Z-Wave (500 series chip)
Frequency band| 868.4 or 869.8 MHz EU
921.4 or 919.8 MHz ANZ
Transceiver range| up to 50m outdoors up to 40m indoors
(depending on terrain and building structure)
Max. transmit power| 1dBm
Note: The transceiver range is strongly influenced by other devices operating at the same frequency with the continuous transmission, such as alarms and radio headphones which interfere with the control unit transceiver.
PRODUCT DISPOSAL
This product is an integral part of the automation and therefore must be
disposed together with the latter. As in installation, also at the end of
product lifetime, the disassembly and scrapping operations must be performed
by qualified personnel. This product is made of various types of material,
some of which can be recycled while others must be scrapped.
Seek information on the recycling and disposal systems envisaged by the local
regulations in your area for this product category.
Caution! some parts of the product may contain pollutant or hazardous
substances which, if disposed of into the environment, may cause serious
damage to the environment or physical health. As indicated by the symbol
alongside, disposal of this product in domestic waste is strictly prohibited.
Separate the waste into categories for dis-posal, according to the methods
envisaged by current legislation in your area, or return the product to the
retailer when purchasing a new version.
Caution! local legislation may envisage serious fines in the event of
abusive disposal of this product.
DECLARATION OF CONFORMITY
Hereby, Nice S.p.A., declares that the radio equipment type Push-Control is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: http://www.niceforyou.com/en/support
Nice SpA
Oderzo TV Italia info@niceforyou.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>