DECRANE AEROSPACE LCDW-9420-101-x 42 Inch High Definition Widescreen LCD Monitor Instruction Manual

DECRANE AEROSPACE LCDW-9420-101-x 42 Inch High Definition Widescreen LCD

Monitor

General Information

Introduction

This manual contains information for the proper installation of the DeCrane Aerospace Audio International 42″ High Definition Widescreen Liquid Crystal Display (LCD) Monitor, Model No: LCDW-9420-101-x. The “-x” suffix designates the type of connector utilized; “-1” = Positronic and “-2” = D-Subminiature. Also included are physical and electrical characteristics of the unit.

Purpose of the Equipment
DeCrane Aerospace Audio International’s LCDW-9420-101-x is a 42″ High Definition Widescreen monitor with a 1920 x 1080 (WUXGA) resolution with a color depth of 10-bits (1.06 billion colors). This is a Color Active Matrix Liquid Crystal Display capable of accepting and displaying multi-format (NTSC,PAL, SECAM) composite video, SD-SDI video compliant to the SMPTE-259M standard, VGA graphics up to 1600 x 1200 (UXGA) resolution, and high- definition component video up to 1080i resolution. This LCD provides accurate color reproduction, has high brightness and contrast ratio, wide viewing angles, and fast response time. The monitor is designed for bulkhead mounting.

Optional Equipment
DeCrane Aerospace Audio International offers a comprehensive family of Cabin Control Modules and Source Equipment. These modules provide convenient solutions for a variety of frequently encountered interfacing needs or special requirements and are an important part of DeCrane Aerospace Audio International’s “building block” system for configuring total cabin management.An optional mounting kit (part number LCDWKIT-9420-01) may be purchased for added mounting provisions. This kit is comprised of angle brackets and spring clips to enable bulkhead and cover bezel installation as well as behind bulkhead installation. Additionally, an optional cover bezel (part number LCDWCB-9420-0x; -01 for a black anodized finish, -02 for no finish) may be ordered. The LCDWCB-9420-0x includes the LCDWKIT-9420-01, so it is not necessary to order both LCDWCB-9420-0x and LCDWKIT-9420-01. Contact your DeCrane Aerospace Audio International representative for details.

Application

The LCDW-9420-101-x is a High Definition Widescreen LCD monitor with Component Video, Composite Video, PC Graphic capabilities, and Serial Digital Interface capabilities. If any one of these formats is applied to their respective inputs, the monitor will display that format. For installations where multiple inputs may be connected and active at the same time, the user can set the monitor input priority via the On Screen Display (see Section 3.8).

Communication
This unit incorporates an RS-485 serial data bus interface for communication purposes to other network-connected devices. All RS-485 serial data bus electronic interface parameters are compliant to DeCrane Aerospace Audio International’s document #640071.

Block Diagram – Typical Application

Typical Interfaces
Typical Video Input (Analog) accept Component Video (up to 1080i), Composite Video (NTSC, PAL, SECAM), and PC graphics up to 1600 x 1200 UXGA resolution.The Digital Video Input accepts SD-SDI video as defined by ANSI/SMPTE 259M-1997.SP-LCD6 is an external switch utilized for monitor set- up. The switch, which must be ordered separately, provides configuration control via DeCrane Aerospace Audio International’s proprietary RS-485 digital data bus communication or may be configured directly to the J2 connector. Refer to Section 3.8, Configuration Overview, for monitor set up. The SP-LCD6 may be removed and stored after the monitor is set up or can be mounted near the monitor for frequent use. Connector J2 provides to the switch panel +28 VDC power and ground input, serial data bus control, and unit ID strapping pins to allow programming of multiple units.Device addressing is accomplished via three (3) ID pins, which allow for a total of eight (8) monitors to be independently addressed on the data bus.

Installation

Prior to installation, the following items should be considered: During the design and layout of the aircraft cabin, careful consideration of the location of this module is necessary. Some of the items to be considered include:

• Space
• Available power supply
• Environmental conditions (temperature, humidity, etc.)
•  Length of cable runs

The LCDW-9420-101-x shall be installed to conform to the standards designated by the customer, installing agency, and existing conditions as to the unit location and type of installation.  If the adjustment switch (SP-LCD6) is to be mounted in the aircraft, the following should be considered; the pigtail is 24 inches (60.96 cm) in length ±1 inch (2.54 cm) and has 6-32 x 0.75 inch mounting studs. Refer to Sections 6.2 and 7.2 for the adjustment switch characteristics.   An internal cooling fan ventilates internal components and prevents undesirable heat buildup. Proper ventilation must be allowed for when specifying the installation location. The closeout area of the monitor shall have a clearance of 2 inches (5.08 cm) minimum for the air inlet and exit areas. The closeout area of the monitor case shall not block the air inlet or exhaust openings of the monitor case. This fan is thermostatically controlled, it only runs when the unit is turned on and heat build-up requires it, providing a much quieter viewing experience than many monitors.  The monitor casing is specially designed for EMI and noise filtering, guaranteeing a reduction in interference to ensure a high-quality display.

• A shallow mounting depth makes this monitor ideal for bulkhead use. Convenient mounting holes are strategically located on the left and right sides, as well as the back of the unit. The unit has eight (8) 8-32 UNF-2B on the left and right sides, four (4) on each side. The maximum depth should be no more than 0.50 inches. In addition, the unit has eight (8) 8-32 UNF-2B on the back. The maximum depth should be no more than 1 inch. Refer to Section 7.0, Reference Drawings, for mounting hole diameters and configuration.
• An optional front cover bezel (see Section 1.3) may be purchased for added mounting capabilities. Other plating options are available and allow matching to other cabin décor of the aircraft.
• The monitor should be located as close to the source equipment as possible in order to reduce the possibility of noise being introduced into the video. Refer to Section 6.0 for unit dimensions.
• The LCDW-9420-101-x is configured using the external menu selection switch, SP-LCD6. The switch utilizes a D-Subminiature connector. This connector mates with the D-Subminiature connector on the LCDW-9420-101-x model monitor.
• A grounding lug is included as part of the housing. See Section 7.0 for details.
•  The maximum length of the connection to PC Graphic (VGA) input is 15 feet.

Unpacking and Inspection

• Carefully open the packaging and remove the LCDW-9420-101-x. Verify that all components have been included in the package per the packing list. Inspect the unit for damage. Retain the packing materials and packing list.
• If damage has occurred during shipping, a claim should be filed with DeCrane Aerospace Audio International WITHIN 24 hours and a Return Request Authorization Number shall be obtained from DeCrane Aerospace Audio International by contacting the Repair Department at 501.801.8101. Repackage the unit in its original packaging materials and return it to DeCrane Aerospace Audio International following instructions given by the DeCrane Aerospace Audio International representative. Refer to the front cover of this manual for address. If no return is necessary, retain the packing list and the packing materials for storage.

Cautions and Warnings

• It is important to do a pin-to-pin power and ground check on all connectors. Ensure that power and ground are applied only where specified. Damage to the unit may result if power or ground is applied to the wrong points.
• DO NOT connect or disconnect the monitor while power is applied.
•  DO NOT remove any factory-installed screws. Damage to the unit may result and void any warranties.
•  DO NOT expose to moisture.
•  The SP-LCD6 can be removed and stored after the monitor is set up or it can be mounted near the monitor for frequent use. Ensure power is removed from the monitor and/or entertainment system before connecting or disconnecting the SP-LCD6.
• ESD (Electro Static Discharge) guidelines shall be followed.

Wiring Requirements

• The installing agency shall supply and fabricate all external cables and mating connectors. The length and routing of external cables should be carefully studied and planned before attempting installation of the equipment. Allow adequate space for installation of cable and connectors. Avoid sharp bends and placing cables near aircraft control cables. Maintain a minimum clearance of three (3) inches from any control cable. If wiring is run parallel to combustible fluid or oxygen lines, maintain a separation of six (6) inches between the lines.

Bonding

• Chassis ground connection shall be bonded to the airframe ground with less than 0.01 ohm resistance using copper flat braid. It is recommended to keep the length of the connectionless than six (6) inches.

Power Wires

• Power and Ground wires shall be in accordance with M22759 or equivalent. Protect power wires with circuit breakers or fuses located close to the electrical power source bus.

Composite Video

• Composite Video connections shall be shielded coaxial cable in accordance with M17/94-RG179 or equivalent. Cable shields shall be grounded at the source. Use of individual wires rather than proper coaxial cable connections through production breaks is unacceptable and will cause significant and detrimental noise introduction to the video signal supplied to the LCDW-9420-101-x.

SDI Video

• SDI video connections are recommended to use shielded coaxial cable V76261 from PIC Wire and Cable using a single run of cable no greater than 50 meters. Connectors with an impedance of 75-ohm should be used where cable discontinuities may occur.

RS-485 connections

• connections shall be twisted shielded cable with the shield properly grounded at the source (ideal practice) and floating at the load end. If shield cannot be grounded at the source, then ground at the load end with the source end floating. Each wire length shall be terminated at one end only. The shield for RS-485 shall be terminated to a dedicated pin. Twisted shielded cable shall be in accordance with NEMA WC 27500 or equivalent.

RGB Connections

• RGB wiring shall be in accordance with NEMA WC 27500 or equivalent.
• Electrical Characteristics
• Electrical Specifications for LCDW-9420-101-x:

178° Vertical

Analog Video Input

| 1080i Analog Component,

Composite (NTSC, PAL, and SECAM).

1Vp-p @ 75 0

PC Graphics Input

| RGB + HV

714mVp-p @ 75 0 (RGB)

4Vp-p (HV)

Up to (1600 x 1200)

UXGA resolution

Digital Video Format| ANSI/SMPTE 259M-1997
Operating Temperature| +5° to +131° F

-15° to +55° C

Storage Temperature| -4° to +131° F

-20° to +55° C

Electrical Specifications, SP-LCD6:

The LCDW-9420-101-x utilizes three (3) connectors. J1 is a 13-pin connector that provides power input, ground, video input, monitor on/off control and monitor status.
The monitor on/off function (J1, Pin 5) is transition level sensitive. Either a constant ground input or momentary ground input may be used. If constant ground input is used, the monitor will activate to the ON state when +28VDC power is applied to Pin 1 and a constant ground is on Pin 5. If no constant ground is present, then this input will float to a high level causing the monitor to be in the OFF state.
If momentary ground input is used, the monitor will alternate between ON and OFF states with each momentary ground pulse of duration between 50 and 250 msec. If momentary ground logic is used, then the monitor will power up to an OFF state when power is applied to Pin 1.

• J2 is a 9-pin connector that provides power output to the SP-LCD6, ground, and data bus control. Three (3) ID pins are also provided on the J2 connector. These ID pins allow for up to eight (8) units to be connected on the same DeCrane Aerospace Audio International’s proprietary RS-485 data bus while maintaining independent control of each unit. Depending upon the necessary configuration, the ID 0, ID 1, and ID 2 pins shall connect to the ID common as suggested below:

0 = Connected to ID Common       1 = N/C

• J3 is a 15-pin high-density connector that provides VGA signal to the monitor. This unit can accept 1080i analog component video on the VGA connector, in addition to computer graphics. the LCDW-9420-101-x. This connector provides +28 VDC power input, ground, data bus connections, and data bus configuration ID connections.
• Mating Connector Information All wiring harnesses to the unit shall be supplied and fabricated by the installing agency.
  J1 CONNECTOR:****

All wiring harnesses to the unit shall be supplied and fabricated by the installing agency.| All wiring harnesses to the unit shall be supplied and fabricated by the installing agency.
---|---
J1 CONNECTOR:| J1 CONNECTOR:
All wiring harnesses to the unit shall be supplied and fabricated by the installing agency.| All wiring harnesses to the unit shall be supplied and fabricated by the installing agency.

• J2 CONNECTOR

LCDW-9420-101-2

| DEMA-9S Female Plug with male jackscrews or equivalent

(ITT Cannon)

J3 CONNECTOR:

LCDW-9420-101-2

| DAMA15PK87 Male Plug with male jackscrews or equivalent

(ITT Cannon)

J4 CONNECTOR:

Pinout assignment for the LCDW-9420-101-x is as follows:

J1

Pin #| Description
1-3| Reserved
4| Monitor Status Gnd Output
5| Monitor On/Off Gnd Input
6| SE Video Enable
7| SE Video Common
8-10| Reserved
A1| Composite Video
A2| Serial Digital Video
A3| Reserved

Pins 6 and 7 must be tied together for single-ended Composite Video sources and should only be connected if a differential video source is not driving pin A1.

J2

Pin #| Description
1| +28VDC Power Output For Monitor Control Panel
2| Ground
3| Data Bus A
4| Data Bus B
5| Data Bus Shield
6| ID0
7| ID1
8| ID2
9| ID Common
J3

Pin #| Description
1| Red Video
2| Green Video
3| Blue Video
4| Reserved
5| Ground
6| Red Video Ground
7| Green Video Ground
8| Blue Video Ground
9| Key
10| Sync Ground
11-12| Reserved
13| Horizontal Sync
14| Vertical Sync
15| Reserved
J4

Pin #| Description
A| 115 VAC 400HZ Hot
B| 115 VAC 400HZ Ground
C| 115 VAC 400HZ Neutral
D-F| Reserved

Wiring description for the SP-LCD6 is as follows:

SP-LCD6

Pin #| Description
1| + 28 VDC Power Input
2| Power Ground
3| Serial Data Bus A (HI)
4| Serial Data Bus B (LO)
5| Serial Data Bus Shield
6| Unit ID 0
7| Unit ID 1
8| Unit ID 2
9| Unit ID Common

Configuration is typically accomplished via an SP-LCD6 attached to the D-Subminiature connector on the monitor. DeCrane Aerospace Audio International reserves the right to add, delete, or alter functions from the setup menus without advance notification to the user. To access the Main Menu, press the “MENU 1” button, which will cause the Monitor setup menu to be displayed on the LCDW-9420-101-x. To scroll through the setup modes, press the “MENU 2” button to scroll forward or the “MENU1” button to scroll back. When in the desired mode for setup monitor, press either LEFT (-) or RIGHT (+) to change the selected value. Pressing the LEFT button decreases the selected value and pressing the RIGHT button increases the selected value. Press the appropriate button for the desired adjustment. Press the “MENU 2” button to scroll to the next menu option.

A typical Monitor Setup Menu consists of the following modes:

1. “OSD TIMEOUT”- Timeout period until monitor defaults out of menu mode.
2. “BACKLIGHT”- Backlighting intensity.
3.  “FACTORY PRESET”- All modes may be reset to the default factory setting. Select either “YES” or “NO”.
4. 4. “SOURCE PRIORITY”- Selects priority operating mode to “PC” (personal computer) or “None”. Setting this mode to “PC” allows user to normally view Composite Video until a PC laptop is turned on, then the monitor will automatically switch to PC input upon sensing VGA input.
5. “H-POS”- Adjusts viewing area horizontally.
6. “V-POS”- Adjusts viewing area vertically.
7. “SHARPNESS”- Adjusts picture sharpness.
8. “COLOR”- Adjusts picture color.
9.  “TINT”- Adjusts picture tint.
10. “CONTRAST”- Adjusts picture contrast.
11. “BRIGHT”- Adjusts picture brightness.

The setup menu may vary slightly from monitor model to model. As technology advances, additional features may be added to the setup menu and existing features may be modified. DeCrane Aerospace Audio International’s intention is to provide clear and concise instructions on any new or modified feature in the setup menu as these changes occur.

Instructions for Continued Airworthiness
No periodic scheduled maintenance or calibration is required for the continued airworthiness of the LCDW-9420-101-x. If the unit fails to perform to specifications, it must be removed and serviced by a qualified service facility.

Troubleshooting

Cleaning Method The LCDW-9420-101-x should be cleaned when excessive dust or dirt becomes apparent.
Use a twin pack cleaning system that employs a wet pad pre-moistened with an Isopropyl Alcohol based cleaner/anti-static solution and a lint-free drying cloth. DeCrane Aerospace Audio International recommends using “Kleen & Dry” RR1205 manufactured by reading RIGHT, Nanuet, NY 10954.

• Do not use benzene, ammonia, thinner, or any other volatile substance to clean the monitor or screen. These chemicals may damage the screen or internal circuitry.
•  Do not allow cleaner to puddle or pool around edges. Seepage may damage internal circuitry.

DeCrane Aerospace Audio International’s recommended cleaning method follows:

• Turn off monitor.
•  Open pre-moistened pad and gently wipe evenly across display glass. Do not allow solution to “pool” or puddle around display edges.
•  Immediately dry display using the absorbent, lint-free cloth. Gently wipe display to a dry, clear finish.

General Troubleshooting Procedures

• Verify power to the unit by rechecking +28 VDC power is applied to the proper pins on the unit. Use a voltmeter to verify correct level.
•  Remove power from the unit for at least one (1) minute and reapply power.
•  Recheck all connections to the unit for security. Check all harness runs for possible pinching. Recheck all pinouts for application accuracy.
•  Check data bus integrity by utilizing a voltmeter, oscilloscope, or another voltage instrument to verify proper input voltage on the data bus pins. Typical measurements are as follows:
  •  to Ground: 4.0 to 4.5 VDC
  • to Ground: 0.1 to 1.0 VDC

If any device is transmitting (i.e., holding bus active), then these typical measurements would be reversed for the A-to-Ground and B-to-Ground. This troubleshooting tool can help indicate a data bus lockup. If this occurs, remove the data bus from all other equipment one piece at a time. As each is removed, check the bus status to see if it is now functioning properly. Once you have removed the piece or pieces of offending equipment, disconnect power and then reconnect everything but the suspect component. Reapply power and then test the functionality of the unit(s).

Troubleshooting Chart

Poor picture quality or scrambled video

| ► LCD backlight malfunction

► SP-LCD6 programming

► Poor video source

| ·         Contact DeCrane Aerospace Audio International

·         Check setup

·         Verify function of video source

 | ► LCD not receiving power| ·         Check all cable connections
Blank screen*| ► Mother board malfunctioning| ·         Contact DeCrane
 |  | Aerospace Audio
 |  | International

The monitor displays a black screen with the unit turned on and no video signal.

Specifications

Unit Specifications for LCDW-9420-101-x:

Physical Specifications – LCDW-9420-101-x

 |
Housing| Iridited Aluminum

(with black powder-coat finish)

Screen Size| 42″ (106.68 cm) diagonal
Weight| Approx. 41.00 ± 1.00 lbs / 18.68 ± 0.45 kg
Dimensions (l x w x h)| 38.87″ x 2.85″ x 22.88″

98.73 cm x 7.24 cm x 58.12 cm

Note:
This does not include optional bezel and bezel mounting bracket.

Unit Specifications for SP-LCD6:

Physical Specifications – SP-LCD6

 |
Bezel Plating| Raw, unless otherwise specified
Weight| Approx. 0.13 lb / 0.06 kg with connector
Dimensions

(l x w x h)

| 2.53″ x 1.54″ x 2.38″

6.43 cm x 3.91 cm x 6.05 cm

Note: These dimensions are for the cutout. Note: These dimensions are for the cutout.

 Reference Drawings

LDCW-9420-101-x – High Definition Widescreen LCD Monitor The following diagrams show the unit dimensions, mounting locations, and connector locations for the LCDW-9420-101-x.

SP-LCD6 – External Menu Switch
The following diagrams show the unit dimensions and connector locations for the external menu selection switch, SP-LCD6.

References

• decraneaerospace.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>