miliwave MWC-708 11AX MU-MIMO OFDMA Dual Band Embedded Board Instruction Manual
- June 1, 2024
- miliwave
Table of Contents
MWC-708
11AX MU-MIMO OFDMA Dual Band Embedded Board
Features
- Quad-core ARM 64bit A53@1.8GHz Processor
- 1GB DDRL3L System Memory
- 8MB NOR Flash, 256MB NAND Flash
- Supports Dynamic Frequency Selection (DFS)
- 2×2 On-board 2.4GHz radio, up to 573Mbps physical Data Rate
- 2×2 On-board 5GHz radio, up to 1201Mbps physical Data Rat
Applications
- 802.11ax MU-MIMO OFDMA Access Point
- Smart AP TWT
- Industrial environment data transmission
Product Description
MWC-708 based on Quad-core ARM 64bit A53@1.8GHz chipset is an enterprise wireless module integrated with 2×2 5G high power Radio module and 2×2 2.4G high power Radio module designed specifically to provide users with mobile access to high-bandwidth video streaming, voice, and data transmission for office and challenging RF environment in factories, warehouses establishment.
Absolute Maximum Rating
| Parameter | Rating | Unit |
|---|---|---|
| Supply Voltage | 24V~48V(DC Jack) | V |
| Operating Temperature Range | -40 to +70 | ℃ |
| Storage Temperature Range | -45 to +105 | ℃ |
| Operating Humidity Range | 5 to +95 (non-condensing) | % |
| Storage Humidity Range | 0 to +90 (non-condensing) | % |
Hardware Specifications
| Symbol | Parameter |
|---|---|
| CPU | Qualcomm-Atheros IPQ6010 |
| CPU Frequency | Quad-core ARM 64 bit A53 @1.8 GHz processor |
| System Memory | 1GB (2x 512MB) DDR3L 16-bit interface with 32-bit memory bus |
design
Ethernet Port| 1 x 2.5Gbps Ethernet Ports & POE
USB| 1x USB 3.0 Type-C Port
PoE| 24V~56V passive PoE
48V~56V passive/Active PoE(Suport 802.3bt)
DC Jack| 24V~48V power supply
LED| 2 x LEDs
Serial Port| 1x Serial Port 4 Pin Connector
Wireless| On-board 2×2, 2.4GHz MU-MIMO OFDMA 802.11b/g/n/ax,support
DSSS, OFDM, OFDMA
On-board 2×2 , 5GHz MU-MIMO OFDMA 802.11a/n/ac/ax,max 20dBm per
chain,support OFDM, OFDMA 4x MMCX Connectors
Antenna| 2.4G, 5G Wi-Fi rod antenna-1: ALX19X-221050-00
2.4G, 5G Wi-Fi rod antenna-2: DRA2G5GD002
5G Wi-Fi patch antenna-1: OLX23P-097100-A
5G Wi-Fi patch antenna-2: OLX23P-097100-B
2.4G Wi-Fi PCB antenna: ALX19P-051AA2-02
Nor Flash| 8MB
Nand Flash| 256MB
DDR| 2 x 512MB
Dimension| 120mm x 105mm x 20mm
2.4G WIFI|
---|---
Maximum Output Power:| 802.11b: 22.92 dBm
802.11g: 21.42 dBm
802.11n20: 22.34 dBm
802.11n40: 18.72 dBm
802.11ax20: 22.65 dBm
802.11ax40: 18.35 dBm
Operating Band/Frequency:| 2412~2462 MHz(802.11b/g/n20/ax20), 2422~2452
MHz(802.11n40/ax40)
Channel Number:| 11(802.11b/g/n20/ax20), 7(802.11n40/ax40)
5G WIFI|
Maximum Output Power:| 5G Wi-Fi B1:| 5G Wi-Fi B4:
802.11a:16.82 dBm| 21.39 dBm
802.11ac20:18.39 dBm| 23.84 dBm
802.11n-HT20:18.39 dBm| 23.85 dBm
802.11ac40:20.33 dBm| 24.80 dBm
802.11n-HT40:20.33 dBm| 24.81 dBm
802.11ac80:10.06 dBm| 22.10 dBm
802.11ax20:18.08 dBm| 23.59 dBm
802.11ax40:19.80 dBm| 24.24 dBm
802.11ax80:9.52 dBm| 22.10 dBm
Operating Frequency| 5G Wi-Fi B1: 5180-5240 MHz, B4: 5745-5825 MHz
Channel Number| 5G Wi-Fi B1: 7, B4: 8
Channel Separation| 5G Wi-Fi: a/ac20/n20/ax20: 20 MHz, ac40/n40/ax40: 40
MHz, ac80/ax80: 80 MHz
Interface MAP
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
intinterference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
For 5150-5250MHz used indoor only
References
- miliwave
- Wallys 802.11ax, wifi 6, IPQ4029,IPQ4019,IPQ6018,IPQ6000.Router board, wireless card.Access Point-Wallys Communications (Suzhou ) Co., LTD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>