ring 5E92E9 Always Home Cam User Guide
- June 5, 2024
- Ring
Table of Contents
Quick Start
-
Charge your Always Home Cam.
Plugin the docking station and place your Always Home Cam in the dock to charge the battery. When the LED on the docking station stops flashing, move on to the next step. -
Turn on your Always Home Cam.
Press and hold the button on the bottom of the Always Home Cam until its lights start flashing. -
Open the Ring app and select Set Up a Device.
Then follow the in-app instructions. -
Scan this code.
This identifies your device for a fast and easy setup.
Safety and Compliance Information
Use Responsibly. Read all instructions and safety information before use.
FAA Warning – WIP
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN INJURY
BATTERY SAFETY
HANDLE WITH CARE. Your device contains a rechargeable lithium-ion polymer
battery and should be replaced on a hard surface, and if the user suspects
damage, do not attempt repair. Contact Amazon Customer Service for assistance.
Keep the device and its power adapter in a well-ventilated area and away from
heat sources, especially when in use or charging.
For more information about batteries, go to www.amazon.com/devicesupport. Do not charge your device near water or in extremely humid conditions.
PRODUCT SPECIFICATIONS
Device name: Always Home Cam
Model number: 5E92E9
Electrical rating: 5V3A
Temperature rating:0°C-40°C
Support frequency:
BT2400-2483.5MHz
WLAN2.4 G2400-2483.5 MHz
WLAN 5G5150-5350MHz
WLAN 5G5470-5850 MHz
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make
sure you dispose of or recycle, your device in accordance with your local laws
and regulations. For information about recycling your device, go to
www.amazon.com/devicesupport.
Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at
ring.com/terms
For information on our warranty, theft protection, and Ring Protect Plans, see
ring.com/legal
FCC Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a
Product by the user that are not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines. Information on
the product is on file with the FCC and can be found by inputting such
Product’s FCC ID (which can be found on the device) into the FCC ID Search
form available at fcc.gov/oet/ea/fccid. The party responsible for FCC
compliance is: Ring LLC, 1523 26th St, Santa Monica, CA USA, 90404
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provided with antenna
installation instructions and consider removing the no-collocation statement.
1523 26th St.
Santa Monica, CA 90404
© 2021 Ring LLC or its affiliates.
Ring and all related marks are trademarks of Ring LLC or its affiliates.
xx-xxxxxx-xx
References
- Legal Information, Support & Resources | Ring
- Terms of Service | Ring
- Amazon Digital Services and Device Support - Amazon Customer Service
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>