Queclink QLM100 EGPRS-LTE Cat-M1-LTE Cat-NB2 Module User Manual

QLM100 User Manual
EGPRS/LTE Cat-M1/LTE Cat-NB2 Module
TRACQLM100UM001
Version: 1.00

QLM100 User Manual

General Notes

Queclink offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Queclink. The information provided is based upon requirements specifically provided to Queclink by the customers. Queclink has not undertaken any independent search for additional relevant information, including any information that may be in the customer’s possession. Furthermore, system validation of this product designed by Queclink within a larger electronic system remains the responsibility of the customer or the customer’s system integrator. All specifications supplied herein are subject to change. Queclink mers, to support, to support y Queclink. The inform. The in ed to Queclink by the customed to Queclink by the customer arch for additional relevant information h for additional relevant inf customer’s possession. Furthermore possession. Further y Queclink within a larger electro k within a larger elec customer or the customer’s system or the customer’s syst re subject to change. o change.

Copyright

This document contains proprietary technical information which is the property of Queclink Wireless Solutions Co., Ltd. The copying of this document, distribution to others, and communication of the content thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of a patent grant or registration of a utility model or design. All specifications supplied herein are subject to change without notice at any time. right right is document contains proprietary document contains propriety eless Solutions Co., Ltd. ess Solutions Co., Ltd unification of the c unification of thee to the pa to the ratio Confidential g edition remains the All specifications ll specifications formation which is the property of Q rmation which is the property g of this document, distribution t s document, distribution of, are forbidden without express of, are forbidden without express mages. All rights are reserved in t s. All rights are reserved in t model or design. All specification design. All specifications tice at any time ny time.

Introduction

QLM100 module is an LTE Cat M1/ Cat NB2/ EGPRS module and a baseband processor platform based on ARM Cortex A7. The maximum dominant frequency is up to 800MHz. It provides data connectivity on LTE-TDD/LTE-FDD/GPRS/EDGE networks, and supports half-duplex operation in LTE networks. It also provides GNSS to meet customers’ positioning demands. The following table shows the frequency bands ofQLM100 module.

1.1. Reference

Table 1: QLM100 document Reference

Product Overview

2.1. Description
QLM100 is an embedded IOT wireless communication module.

2.2. Pin Definition
The sequence and description of the pins are shown in the following figure.

Figure 3. QLM100 Pin map

Table 2: QLM100 Pin description.

**PIN N O .| ****QLM100 Net Name**|

**Description**

---|---|---
1| PSM_IND| Power saving mode indication
2| ADC1| General purpose analog to digital converter interface
4| PCM_CLK| PCM clock output
5| PCM_SYNC| PCM frame synchronization output
6| PCM_IN| PCM data input
7| PCM_OUT| PCM data output
11| I2C2_SDA| I2C2 serial clock.
12| I2C2_SCL| I2C2 serial clock.
13| GPIO27| General purpose input/
| | output interface
14| UART2_TX| Transmit data
16| UART2_RX| Receive data
18| W_DISABLE#| Airplane mode control
19| AP_READY| Application processor sleep state Detection
20| STATUS| Indicate the module’s Operation status
21| NETLIGHT| Indicate the module’s Operation status
22| DBG_RXD| Receive data
23| DBG_TXD| Transmit data
24| ADC0| General purpose analog to digital converter interface
25| ADC2| General purpose analog to digital converter interface
26| GPIO46| General purpose input/ output interface
27| UART3_TX| Transmit data
28| UART3_RX| Rec ive data
30| DTR| Data terminal ready (sleep mode control)
34| RXD| Receive data
35| T D| Tran mit data
36| CTS/9205_RTS| Clear to send
37| RTS/9205_CTS| Request to send
38| DCD| Data car ier detection
39| RI| Ring indication
40| I2C1_SCL| I2C1 serial clock.
41| I2C1_SDA| I2C1 serial clock.
42| USIM_PRESENCE| (U)SIM card insertion detection
63| GPIO41| General purpose input/ output interface
64| GPIO44| General purpose input/ output interface
65| GPIO26| General purpose input/ output interface
66| GPIO28| General purpose input/ output interface
76| GPIO37| General purpose input/ output interface
77| GPIO36| General purpose input/output interface
| |
---|---|---
78| GPIO38| General purpose input/ output interface
83| GRFC_2| General purpose input/ output interface
84| GRFC_1| General purpose input/ output interface
85| GPIO5| General purpose input/ output interface
86| GPIO25| General purpose input/ output interface
87| GPIO49| General purpose input/ output interface
92| GPIO3| General purpose input/ output interface
93| GPIO33| General purpose inp t/ o t pu t in te rface
94| GPIO35| General purpose input/ ou tp ut interface
95| GPIO34| General purpose input/ output interface
96| PO _1|
97| GPIO40| General purpose input/ ou tp ut in te rfac e
98| G IO42| General purpose input/ output interface
8| USB_VBUS| USB Interface
9| USB_DP| USB Interface
10| USB_DM| USB Interface
75| US _BOOT| USB Interface
15| PW KEY| Turn on/off the Module
17| RESET_IN| Reset the Module
29| VDD_EXT| Provide 1.8V for external circuit
32| VBAT_BB| Power supply
33| VBAT_BB| Power supply
43| USIM_VDD| (U)SIM Interface
44| USIM_RST| (U)SIM Interface
45| USIM_DATA| (U)SIM Interface
46| USIM_CLK| (U)SIM Interface
47| USIM_GND| (U)SIM Interface
---|---|---
52| VBAT_RF| Power supply
53| VBAT_RF| Power supply
49| ANT_GNSS| Antenna Interfaces
60| ANT_MAIN| Antenna Interfaces
103| MDM_PS_HOLD|
104| JTAG_TDI| JTAG Interfaces
105| JTAG_SRST_N| JTAG Interfaces
106| JTAG_TMS| JTAG Interfaces
108| JTAG_TDO| JTAG Interfaces
109| JTAG_TCK| JTAG Interfaces
110| JTAG_TRST_N| JTAG Interfaces
3, 31, 48,50, 54, 55, 58, 59, 61, 62, 67~74, 79~82, 89~91, 100~102,107 , 111~114| GND| Ground
51, 56,57,88,99| RE ERVE| RESERVED

Getting Started

3.1. Module & EVB
The QLM100_EVB can be used to test the module.

3.2. Power on the Module
Connect the 12V charger with EVB, switch the POWER to ON and then press the power TRACQLM100UM001

key. Note: The Force_USB should be on switch to the side as the Figure5 shows.

3.3. Send command by the USB

Connect the EVB with micro USB cable interface to send the command to the module.
Step1. Install USB driver ” qud.win.1.1_installer_10065.1″ on your PC. Send command the E o USB cable interface to send com able interface to send c river.
Step2. Power on the device.on the device. e.
Step3. Connect the USB, you will find the two COM port on PC management, select the one except “Qualcomm HS-USB MDM Diagnostics 90B2” on QCOM tool

3.4. Upgrade the firmware
step1. Connect 12V charger and USB Cable.
step2. Switch the Power to ON, switch the Force_USB to up as Figure 8.
step3. Press the power key to turn on the module..

step4. Use the tool ” Queclink_Firmware_Upgrade_Tool_MDM_V1.35″ to upgrade

ORIGINAL EQUIPMENT MANUFACTURER (OEM) NOTES

The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and 15.109) before declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.

The OEM must comply with the FCC labeling requirements. If the module’s label is not visible when installed, then an additional permanent label must be applied on the outside of the finished product which states: “Contains transmitter module FCC ID: YQD-QLM100 ”. Additionally, the following statement should be included on the label and in the final product’s user manual: “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.”

The module is limited to installation in mobile or fixed applications. Separate approval is required for all other operating configurations, including portable configuration with respect to Part 2.1093 and different antenna configurations.

A module or modules can only be used without additional authorizations if they have been tested and granted under the same intended end‐use operational conditions, including simultaneous transmission operations. When they have not been tested and granted in this manner, additional testing and/or FCC application filing may be required. The most straightforward approach to address additional testing conditions is to have the grantee responsible for the certification of at least one of the modules submit a permissive change application. When having a module grantee file a permissive change is not practical or feasible, the following guide provides some additional options for host manufacturers. Integrations using modules where additional testing and/or FCC application filing(s) may be required are: (A) a module used in devices requiring additional RF exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not meeting all of the module requirements; and (C) simultaneous transmissions for independent collocated transmitters not previously granted together.

This Module is full modular approval, it is limited to OEM installation ONLY.
Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change. (OEM) The integrator has to assure compliance of the entire end product including the integrated Module. Additional measurements (15B) and/or equipment authorizations (e.g. Verification) may need to be addressed depending on co-location or simultaneous transmission issues if applicable. (OEM) Integrator is reminded to assure that these installation instructions will not be made available to the end user.

FCC Declaration

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The requirement for KDB 996369 D03
List of applicable FCC rules
FCC CFR Title 47 Part 22 Subpart H CFR Title 47 Part 22 Subpart H
CFR Title 47 Part 15 Subpart B
Summarize the specific operational use conditions
This module has been granted Single Modular Approval for mobile applications.
OEM integrators for host products may use the module in their final products without additional
FCC certifications if they meet the following conditions. Otherwise, additional FCC approvals must be obtained.
The host product with the module installed must be evaluated for simultaneous transmission requirements The user’s manual for the host product must clearly indicate
the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation.
A label must be affixed to the outside of the host product with the following statement: This device contains FCC ID: YQD-QLM100
The final host/Module combinations may also need to be evaluated against the FCC Part  15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.
Information on test modes and additional testing requirements
Consider multi-transmission mode in the host.
Additional testing, Part 15 Subpart B disclaimer by FCC Part 15 Subpart B. The host be evaluated by the FCC Subpart B.
Single module procedures
The module has meet the requirements to satisfy the conditions.
Trace antenna designs
Please refer to the RF Link’s schematic diagram and refer to PCB Layout.
RF exposure considerations

The host device manufacturer should confirm that a separation distance of 20cm or more should be maintained between the antenna of this host device and persons during the host device operation.
Antennas
The device itself has an antenna, customer can use the PIFA antenna with an antenna gain that isn’t greater than 3 dBi.
Lable and compliance information
If this certified module is installed inside the host device, then the outside of the host must be labeled with ”Contains FCC ID: FCC ID: YQD-QLM100 “

References

• PDF Tools, Document Process Software, Multimedia Applications and Development Packages - VeryPDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>