Anytrek VT1611 TrackLight User Manual
- June 5, 2024
- Anytrek
Table of Contents
VT1611
Track light User and Installation Guide
truck.anytrek.com
Introduction
Thank you for purchasing the TrackLight GPS tracker from Anytrek.
Your TrackLight provides the ultimate `plug and drive’ covert tracker
providing the ability to track your asset in real-time from any web-connected
device. It comes complete with an integrated SIM card for the tracking
function and is simple and quick to install. With your TrackLight, you also
have access to the Anytrek web portal, as well as the smartphone apps for both
Android and iOS devices. The Quick Start guide for the portal can be
downloaded from anytrek.com. You should have your user credentials to login
into the portal by now, if you don’t please contact Anytrek on 1 844 872 6987.
Operating Characteristics.
Reporting Frequency:
From 15 minute reporting cycle whilst motion/movement is detected 12-hour
reporting cycle while stationary
Power characteristics:
Power/Recharge from both tail and brake light circuits Battery recharge
temperature range; -5° C to +55° C (Outside this range the charging function
is suspended)
Installation
track light has been designed to look, function, and install exactly the same as a standard 4″ LED tail light. It can be mounted using either a standard rubber grommet, stainless steel mounting ring or Anytrek’s Perma-Lock snap-fit mounting ring. track light connects to the vehicle’s standard wiring lead using a Fit N Forget connector. If your vehicle uses an earlier PL-3 connector, Anytrek offers adaptor cables that remove the need to cut the existing wiring leads.
Important
track light connects to the tail light and brake light circuits in order to
draw power. Please ensure that your TrackLight is fitted to an existing
tail/brake light, and not a turning indicator or reversing light.
Installation
The following short video clip shows the installation process for a
TrackLight GPS tracker using an existing rubber grommet. If the existing tail
light is held in place with a steel mounting ring, it will have to be removed
first.
Click on the logo below to view the installation video on YouTube.
Activation
Please follow the steps below to create your user account and register the tracker. If you already have an account for the Any truck portal, log in, go to Device Manager and add your new tracker.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party. Responsible for compliance could void the user’s
authority to operate this equipment. (Example- use only shielded interface
cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and your body.
IC Warning
English: This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This
device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canadian radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Support
We’re never far away!
For technical support either email us on;
support@anytrek.com
Or call us on; +1 (844) 872 6987
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>