SwitchBot W1701100 LED Strip Light User Manual

: June 5, 2024
: SwitchBot

Table of Contents

Package Contents
Preparation
Getting Started
- Installation Procedure
- Functions of the Controller
Safety Information
Firmware and Factory Reset
Specifications
Return and Refund Policy
Contact and Support
FCC Warning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SwitchBot W1701100 LED Strip Light

Package Contents

LED strip light (5m/ 16.4 ft)

|

Controller

|

Power adapter

---|---|---

Remote control

|

Mounting buckles x 6

|

User manual

Preparation

A smartphone or tablet with Bluetooth 4.2 or above.
System Requirements: Android 5.0 or above, iOS 11 or above.
Download the SwitchBot app and create a SwitchBot account and sign in.

|
---|---
|

Getting Started

Installation Procedure

Clean the surface.
Peel off the strip liner on the back, then stick the LED strip light on a flat, clean and hard surface.
Peel off the strip liner on the back of the mount and stick the mounting buckles on the surface.
Plug in the power adapter.
Control the LED strip light by using the remote control, controller or the app

Functions of the Controller

Safety Information

NOT FOR EMERGENCY LIGHTING.
Before using this product, check your electricity voltage. Inappropriate voltage will damage the product and cause safety issues.
Only cut the strip light at the designated point. The part cut will not work.
Cut the strip light only when the power is off. Otherwise, this can lead to short circuit.
Please keep the surface for installation clean and even for easy adhesion
Use the mounting buckles on surfaces such as wallpaper and for a more secure installation.
The strip light is NOT waterproof, keep away from water.
Only use the product indoor. When in use, maintain a good airflow for cooling.
Operating temperature: -15°C to 40°C (5°F to 104°F)
Storage temperature: -20°C to 70°C (-4°F to158°F)
Relative humidity: 10% to 90% noncondensing
Storage humidity: 10% to 90% noncondensing

Firmware and Factory Reset

Firmware
Make sure you have the most updated firmware by upgrading in time.

Factory Reset
Press the power on/off button and music mode button for 8 seconds until red green and blue light flow through the LED strip light.

Note: After resetting the device, all settings will resume to its default values.

Specifications

Model Number: W1701100
Rated Power: 11W
Input Rating: 100-240 VAC
Wireless Connection: 802.11 b/g/n (2.4 GHz)
Color Type: RGB
Dimming Range: 1% to 100%
Ways of Control: Controller, app, voice control & remote control
Operation Life: Around 25000 hours

Return and Refund Policy

This product has one-year warranty (begins from the date of purchase). The situations below do not fit the Return and Refund Policy

Intended damage or abuse.
Inappropriate storage (drop down or soaking in water).
Modify or repair of product.
Natural wearing of product.
Natural disasters.

Contact and Support

Setup and Troubleshooting:
support.switch-bot.com

Support Email:
support@wondertechlabs.com

Feedback: If you have any concern or problem when using our product, please kindly send feedback from the Profile > Feedback page in the SwitchBot app.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.