Shenzhen Tianqiao Science Technology K52S Series Smart Switch Instruction Manual

K52S Series Smart Switch
Manual

This user manual applies to:

• Wifi switch

Installation

Warning: Make sure the power supply totally been cut off for the switch you are replacing.

1. Remove your old switch from the junction box
2. As shown in these diagrams below, insert wires into the corresponding terminal holes and fasten them.
3. Take off-panel and fix switch with screws to the junction box in the wall.

• For Dimmer switch Dimmer switch
  CERTIFICATE: CE, ROHS
  INPUT: 100-240V-50/60HZ
  OUTPUT: 300W/gang
  Wireless protocol IEEE: 2. 4GHz
  SIZE: 7012041mm

• Neutral switch CERTIFICATE: CE, ROHS
  INPUT: 100-240V-50/60HZ
  OUTPUT: 500W/gang
  Wireless protocol IEEE: 2. 4GHz
  SIZE: 7012041mm

• • Nonneutral switch CERTIFICATE: CE, ROHS
    INPUT: 100-240V-50/60HZ
    OUTPUT: 150W/gang
    Wireless protocoljlEEE: 2. 4GHz
    SIZE: 7012041mm

Warning: Make sure the power supply totally been cut off for the switch you are replacing.

1. Remove your old switch from the junction box
2. As shown in these diagrams below, insert wires into the corresponding terminal holes and fasten them.
3. Take off-panel and fix switch with screws to the junction box in the wall.

• For Dimmer switch Dimmer switch
  Model: TY-TJ-WUSH62S-T1D
  CERTIFICATE: CE, ROHS
  INPUT: 100-240V-50/60HZ
  OUTPUT: 300W
  Wireless protocoljlEEE: 802. 11 b/g/n, 2. 4GHz
  SIZE: 7012041mm

• For 1 gang switch 1 gang switch
  Model: TY-TJ-WUSH62S-L1D
  CERTIFICATE: CE, ROHS
  INPUT: 100-240V-50/60HZ
  OUTPUT: 1000W/gang
  Wireless protocoljlEEE: 802. 11 b/g/n, 2. 4GHz
  SIZE: 7012041mm

• For 1 gang 2-way switch

Add switch to APP

1. Download Smart Life APP from APPstore and register

2. Preparations before get started
   • For WiFi switch
   A wifi router is required,the wifi switch only supports 2.4GHz WIFI network.

3. Power up the switch,press and hold the button(for about S seconds) until the indicator blinking to enter pairing mode,then do the following steps for adding.

• For WiFi switch****
  

  1. Open Smart Life APP,tap the icon + on the top right in the homepage.| 2. Tap Electrical–Switch(WI-FI), enter into Add Device
  
  3. Choose your local wifi and input wifi password| 4. Comfirm the indicator is blinking rapidly.—(Long press any switch button for about 5 seconds then indicator will blinking)
  
  5. Wait for configuring successfully,then tap Cpmplete and edit name

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation di stance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>