TOORX 49447-TU Motion Plus Treadmill Instructions

49447-TU Motion Plus Treadmill
Instructions

When you open the carton, you will find the below parts in the carton

PART LIST：

NO.| DES.| Specification| Nos
•| .| NO.| DES.| Specification| Nos
•
---|---|---|---|---|---|---|---|---
1| Mainframe| | 1| | 64| Lock washer| 8| 6
12| 5#Allen wrench| | 1| | 70| Bolt| M845| 2
19| Bolt| 4. 219| 2| | 71| Safety key| | 1
37| IPAD rack| | 1| | 72| Silicone oil| | 1
51| Bolt| M8*16| 4| | 74| MP3 wire| option| 1
59| Left base cover| | 1| | 78| Wrench with screw
driver| | 1
60| Right base cover| | 1| | | | |

FIXING TOOLS:
5# Allen Wrench 5mm 1PC
Wrench with screwdriver S=13/14/15 1PC
Notice: Do not get through power before complete assembly

Assembly Instructions

STEP 1： Open the carton, get out the above spare parts, and put the Main Frame onto the level ground.

STEP 2： Holding the computer frame and uprights, use the 5# Allen wrench to lock the computer to the upright tube tight by the bolt (51) and lock washer（64）
Notice: do not press wires inside the tube and check if wires are connected well. Support the upright with a hand to avoid the computer & upright falling down .

STEP 3： 1. Pull up the uprights as in the left picture.
Notice: Support the upright with your hand to avoid falling down to having any hurt.

STEP 4:

1. Use 5# Allen wrench(12)， firstly lock right upright onto the base frame by the bolt(70) and lock washer （ 64 ）, then lock right upright onto the base by the bolt (51) and lock washer (64).
2. The left upright assembly is the same as the right upright.

Notice: Please always support the upright with your hand during assembly to avoid falling down to having any hurt.

STEP 5: Use a wrench with a screw driver(78) to lock the left base cover(59) onto the base frame with a bolt (19).
The right side can be assembled referring to the left side.
NOTICE: the base cover should buckle into the base frame vigorously.

STEP 6:

1. Push the IPAD rack(37) into the computer(35).
2. Put the safety key(71) on the computer and start your exercise.

Please make sure all parts have been fixed properly. Before you use the treadmill, please read the instruction carefully

Folding Instruction

Pulling up: Pull up the base frame at position A, till hearing the sound that the air pressure bar B is locked into the round tube

Pulling down: Support place A with a hand, kick the place of the air pressure bar, then the mainframe will fall down automatically ( Please keep anybody and any pet away from the machine when falling down)

Technical Parameter

BUILT-UP
SIZE(mm)| 15051170649mm| POWER| As the rating label showing
---|---|---|---
FOLDABLE
SIZE(mm)| 8801275649mm| Maximum output
power| As the rating label showing
RUNNING BOARD
SIZE(mm)| 400*1200| SPEED RANGE| 0.8-12KM/H
NET WEIGHT| 45KG
4 LEDD WINDOW
WITH WHITE
BACKLIGHT| Speed, time, distance, incline, Calories, Pulse

Grounding Methods

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This product is for use on a nominal 220-240/100-120 volt circuit and has a grounding plug that looks like the plug illustrated in sketch A in following figure. Make that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. (The below picture is just for reference， the actual plug and jack is depends on the importing country)

Operation Guide

OVERVIEW

SHOWING
SPEED： Display the speed,
TIME： Display the time
INCL./PULSE： Display the incline /heart rate
DIST./CAL.:Display the distance/calories

BUTTON FUNCTION
“PROG/MODE” button: PROGRAM/MODE button, press this button to choose a program from manual mode—P1—P15—time countdown mode—distance countdown mode—calories countdown mode—
FAT;
“START/STOP” button: Press this button to start the machine, the machine will run at the lowest speed or at the speed of the default program after 3 seconds time count down; When the treadmill is running, press this button to stop the machine, the machine will stop smoothly;
SPEED +/-: Adjust the speed. Press the button to adjust the speed when running, and adjust the data when stopping;
SPEED （ 5 ) ）： Adjust the speed quickly
INCLINE +/-: Adjust the incline. Press the button to adjust the incline when running, and adjust the data when stopping;
INCLINE （ 5 ) ）： Adjust the incline quickly Button on the right-hand bar: speed+/Button on the left-hand bar: incline+/-

MAIN FUNCTION:
Turn on the power, all the windows lit 2 seconds, and then enter the manual mode.

1. Start-up quickly(Manual): Get through the power and attach the safety key. After 3 seconds countdown, the treadmill starts and runs from the lowest speed, add and subtract by the SPEED button to adjust the speed. Please press the stop button or of the safety key directly to stop.

2. Countdown mode
   Press the ‘PROG/MODE’ button, it can choose time countdown mode, distance countdown mode, calories countdown mode, and the window will show the default data and glitter. At the same time, press SPEED+/-(INCLINE+/-) to set the data. Press the‘ START’ button, and the machine will run at the lowest speed, you can press SPEED+/-(INCLINE+/-) to change the SPEED(INCLINE). When it counts down to 0, the machine will stop smoothly. Certainly, you can press the ‘STOP’ button or take out the safety key from the console to stop the machine.

3. Preset programs:
   Press the‘ PROG’ button to choose the inner install program from P1—-P15. When setting the program, the time window will show default data and glitter, press SPEED+/-(INCLINE+/-)button to set the running time. Each program has been divided into 20 sections, each exercise time=the set time/of 20. Press ‘START’, and the machine will run at the first section speed and incline. When the section is over, it will enter into the next section automatically, the speed will change as the next section data. When finishing one program, the machine will stop smoothly. During the running, you can change the speed and incline by the SPEED+/-(INCLINE+/-)whenever, when the program enter next sect will come back to the current speed and incline. And you can press ‘STOP’ or take out the safety key to stop the machine whenever.

HEART RATE:
When holding the hand pulse with two hands, the pulse window will show your heart rate after 5 seconds. In order to get the heart rate exactly, please do a test when the machine stops and holds the hand pulse for more than 30 seconds. The heart rate data is just for reference and cannot be as the medical data.

BODY FAT TEST
Press the‘ PROG/MODE’ button under ready condition, till ‘FAT’ shows in the window. ‘FAT’ is body fat test mode. Press ‘ INCLINE +/-to choose parameter ‘ SEX / AGE / HEIGHT / WEIGHT’, and a window will show “-1-”，“-2-”、“-3-”-4-“. When setting each parameter, press SPEED+/- to adjust the data, and a window will show the data press INCLIE+/- button to finish, and the window will show“-5-” and“—” enter into ready condition. Hold the handle pulse with two hands, it will show your BMI data after 5seconds.
Data display and set range

| default| range| mark
---|---|---|---
SEX（F1）| 0（MALE）| 0—1| 0= MALE 1= FEMALE
AGE（F2）| 25| 10—99| 1
HEIGHT（F3）| 170CM| 100-240CM| 1
WEIGHT（F4）| 70KG| 20-160KG| 1

Body fat index comparison

USB FUNCTION( Option)：
When the treadmill is powered on, you may insert any USB memory stick which contains audio files. The computer will detect the audio files on the memory stick and play the music directly.
MP3 FUNCTION( Option)
When the power is on, Contacting the external MP3 equipment, the computer will play. The voice is adjustable from operating the external MP3 equipment, the voice should be adjusted on the proper section to protect the computer loudhailer.
Bluetooth speaker function( Option):
Connect the mobile phone Bluetooth with the Bluetooth speaker on the treadmill, after the success of the connection, you can use the phone to play songs on the Bluetooth speaker.

SLEEP FUNCTION:
A. Stop for more than 10 minutes without any operation, the system completed all showed off into the body of sleep sate.
B. Press any key to wake up console under sleep status.

Safety key function:
Whenever pull out the safety key, the treadmill will stop quickly, all data turn to zero, All the windows display“—”. And the incline remains in the current position. At this time, the treadmill can not do any operation except for turning off the switch. When you put the safety key back in the right position, it will enter into the standby status waiting for command input, and still remains in its incline position. If you choose program mode to start the treadmill now, the incline will adjust according to the program mode, Or the incline won’t move.

Exercise parameter and setting

| Display range| Default data| Default| Setting range
---|---|---|---|---
Speed (KM/H)| 0.81CM/H-12.0KM/H| | |
INCLINE| 15%| | | 0-15%
Time (MIN:SEC)| 0:00-99:59| 30:00| 30:00| 5:00—99:00
Distance (KM)| 0.00-99.9| 1.0| | 0.50-99.9
Calories| 0Kc1-999Kcl| 50Kcl| | 10Kc1-990Kcl

programs table：

Running Belt Adjustment

WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE CLEANING OR SERVICING THE UNIT.
Clean: General cleaning of the unit will greatly prolong the treadmill.
Keep the treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either side of the walking belt and also the side rails. This reduces the build-up of foreign material underneath the walking belt by wearing clean running shoes.
Warning: Always unplug the treadmill from the electrical outlet before removing the motor cover. At least once a year remove the motor cover and vacuum under the motor cover.
RUNNING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low-maintenance deck system. The belt/ deck friction may play a major role in the function and life of your treadmill, thus requiring periodic lubrication. We recommend a periodic inspection of the deck. You need to contact our service center if you find the damage to the deck.
We recommend lubrication of the deck according to the following timetable:

• Light user (less than 3 hours/ week)

| annually
---|---

• Medium user (3-5 hours/ week)

| every six months

• Heavy user (more than 5 hours/ week)

| every three months

We recommend that you buy the lubrication from our distributor or directly from our company.
Attention: Any repair needs a professional technician.

1. We suggest that you should switch off the power for 10 minutes after keep running for 2hours so that it’s good for maintaining the treadmill.
2. For avoiding slipping during running, the belt should be not too loose; for avoiding the more abrasion between the roller and belt and maintaining the machine’s good running, the belt should be not too tight. You can adjust the distance between deck and belt, the belt should be away from the deck about 50-75mm on both sides if the best not too tight and loose.

Center The Running Belt

Place the treadmill on a level surface. Run Treadmill at approximately 6-8KM/H, checking the running condition.
If the belt has drifted to the right, pull out of the save clock and switch, turn the right adjusting bolt 1/4 turn clockwise, then start running until centering the belt. PIC A

If the belt has drifted to the left, pull out of the safety clock and switch, turn the left adjusting bolt 1/4 turn clockwise, then start running until centering the belt.PIC B

Timely adjust the tightness of the belt, for the looseness after a period of time running. Pull out of the safety clock and switch, turn the left and right adjusting bolt 1/4 turn clockwise, then re-start running, and confirm the belt tightness until the belt is right tight. PIC C

EXPLODED DRAWING

PARTS LIST

GARLANDO SPA
Via Regione Piemonte, 32 – Zona Industriale D1
15068 – Pozzolo Formigaro (AL) – Italy
www.toorx.it – info@toorx.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>