ACEFAST E1 Desktop 2-In-1 Wireless Charging Stand User Guide
- June 5, 2024
- ACEFAST
Table of Contents
ACEFAST E1 Desktop 2-In-1 Wireless Charging Stand
Product Diagram
- Wireless charging area (for iPhone12 series)
- LED
- Headset charging area
- Power/FOD LED
- USB-A port
- USB-C port
- Non-slip mat
- Cooling holes
Charging Schematic Diagram
Please ensure that the thickness of phone case is less than 5mm
Package Contents
Wireless charger
USB-C charging cable
User manual
Operation Steps
- Connect the charger to a 9V/2A QC3.0 adapter with a USB-C quick charge cable to switch on the power.
- Put the mobile phone with magnetic suction function near the charging area of the wireless charger, and it will automatically absorb the mobile phone for charging.
- Place your headset in the headset charging area to recharge .
Applicable Devices
-
Smartphones:
Magnetic alignment is only available for iPhone 12 series (for iPhone 12, for iPhone 12 mini, for iPhone 12 Pro, for iPhone 12 Pro Max).
Mobile phones that support Qi wireless charging standard. -
Headset:
For AirPods 2 / Pro, other TWS headsets with wireless charging support. -
Compatible for iPhone 12 case (for MagSafe silicone case / for MagSafe clear case).
LED Status Indication
| LED status | Standby mode | Charging | FOD |
|---|---|---|---|
| LED | On | Off | |
| Power/FOD LED | On | Off | Flash |
Product Specification
Input: 9V/2A Phone
Output: 15W/10W/7. 5W/5W
Headset Output: 3. 0W
USB Output: 5V/1A
Input Interface: USB-C port
Transmission Distance(Phone): 8mm
Conversion Rate(Phone): 73%
Product Size: 156. 75x91x91(mm)/6. 17×3. 58×3. 58(ft)
Safety Instructions
- Charging devices that meet the Qi charging standard.
- Charging output maximum power fast charging 15W, compatible with fast charging 10W, 7. 5W and general charging 5W.
- Magnetic calibration adsorption, mobile phone automatic adsorption charging when put on.
- Safety guarantee: overheating protection, overcurrent protection.
Warning
- Do not pull the power cord hard to avoid the power cord from breaking or falling off.
- Do not disassemble by yourself or throw it into fire or water to avoid short circuit and leakage.
- Do not use in severely high temperature, humidity or corrosvie environments to avoid leakage of electricity due to damage to the circuit.
- When using this product, keep a distance of more than 50cm f rom the pacemaker.
- Only use the wireless receiver conforming to Qi standard to connect with the transmitting terminal.
- The working environment temperature of the charger is 30℃-32℃.
- Do not place the magnetic card, magnetic recording medium and precision machine too close to the charger.
- Keep out of reach of children.
Answer Questions
-
If you’re experiencing interrupted or slow charging check the following:
(1) The back of your phone should not have any metal, pop sockets, or credit cards.
(2) Put the phone in the center of the charging surface (this elts the charging coil in your phone lineup with the one inside the wireless charger).
(3) The wireless charging coil on Sony phones is located slighty below center.
(4) Phone cases should be no thicker than 5 mm for effective charging.
(5) Check whether the adapter is QC3. 0 fast charger. -
If you’re failing to charge your device, please try out thef ollowing
(1) Please restart your cell phone and test with other USB cabel
(2) Please check whether the indicator tums on or not
(3) The wireless charging coil on Sony phones is located slightly below center.
(4) Phone cases should be no thicker than 5 mm for effective charging.
(5) Check whether the adapter is QC3. 0 fast charger. -
If you’re failing to charge your device, please try out thef ollowing
(1) Please restart your cell phone and test with other USB cabel
(2) Please check whether the indicator tums on or not
(3) Please check the adapter is QC3. 0 fast charger (output 9V/ 2A), iPhone original adapter does not match the wireless charger.
(4) Please check your phone case thickness (<5mm). Metal ring or magnetic pad are restricted. -
If you’re using the recommended wireless charger with the QC3. 0 adapter and have removed any potential charging obstructions, but are still experiencing issues, try:
(1) Replacing the cable connecting your the wireless charger.
(2) Rebooting your phone.
(3) Unplug the adapter and reinsert. -
Charging is still slow
The mobile phone itself or the external receiving coil allows the wireless charging current to be different, or the application running consumes a lot of power when the mobile phone is charging. lt is recommended to reduce or colse the application. -
The phone is charging intermittently or the indicator light flashes.
If the charging current is not enough, please use a charging head (adapter) with sufficient power 9V2A or 18W above. -
Heating while charging.
It is normal for the receiving coil or transmitter board to generate heat during wireless charging. If the plate is too warm, take your phone off the plate, and switch the plate off. The plate may switch off automaticaly if it is too hot. When the plate has cooled down, try charging again. -
The charger does not work.
Do not put metal debris or magnetic cards on the charging area .lf the product does not work due to overheating please take off the phone andw ait for it to cool down and try charging again. -
If the host fails, contact after-sales service.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the distance between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
Product Care
Keep away from liquids and extreme heat.
Warranty & Customer Support
For questions, support, or warranty claims, contact us at the mail below that corresponds with your region. Please include your Amazon order number and product mode number.
Amazon US orders: support1@acefast.com
Amazon EU orders: support2@acefast.com
Amazon UK orders: support3@acefast.com
Amazon CA orders: support4@acefast.com
Amazon JP orders: support5@acefast.com
Other region orders: support6@acefast.com
*Please note, ACEFAST can provide after sales service for products purchased from any official ACEFAST store. If you have purchased from local seller, you can also contact them directly for service or warranty issues.
Shenzhen Houshuxia Technology Co. , LTD
www.acefast.com |
support@acefast.com Rm203, 2nd Floor, Building
C, Youth Pioneer Park, Jianshe East Road, Tsinghua Community, Longhua Street,
Longhua District, Shenzhen, P. R. China
Shenzhen, 518000, China