RENPHO Smart Body Tape Measure 2 User Manual
- June 5, 2024
- Renpho
Table of Contents
RENPHO Smart Body Tape Measure 2
User Manual 
Thank you for choosing the RENPHO Smart Body Tape Measure 2! This Bluetooth body tape measure is your personal health assistant It will help you easily measure various body parts so you can keep track of your health and fitness. We hope that you enjoy using it!
Important Safety Instructions
- DO NOT use this device for any purpose other than outlined in this manual.
- DO NOT disassemble or modify the device. There are no user-serviceable parts inside.
- DO NOT subject the device to extreme conditions: extreme temperatures beyond operating temperatures, high vibrations, dusty areas, humid conditions (including any liquid) or direct sunlight.
- DO NOT use excessive force on the tape or the gear. Excessively pulling the tape or grinding the gear may cause permanent damage to the device.
- DO NOT fold or twist the tape as this may cause permanent damage.
- DO NOT use excessive force to pull the tape beyond the maximum length of 150cm/60inch. This may permanently damage the device.
- Be very careful when measuring neck circumference. The tape may accidentally cause choking.
- Children under ten years old must be supervised by an adult when using the tar*.
Specifications
Product Name: Smart Tape
Model: R-Y001
Unit: cm/in
Size: 70mm x 70mm x 26mm
Measuring Range: 150cm/60in
Resolution: 1mm, 1/t6In
Accuracy: t3mm, 23/32in
Working Temperature: 32W – 122°F
Working Humidity: 485%
Battery: 3V CR2032 Stand-by
Current: 1pA Working
Current: 2mA
What’s in the Box
1 x RENPHO Smart Body Tape Measure 2
1 x CR2032 Battery
1 x User Manual
Product Diagram
Buttons
: Press to power on. Press and hold to power off.
: Press to switch the unit between inches and centimeters.
: Press to confirm and send the measurement to the app via Bluetooth. Press
and hold to reset the data.
Install the Battery
- Use your thumb to twist the battery cover slot open.
- Insert the battery and ensure the positive pole is facing up.
- Place the battery cover over the opening, and rotate counterclockwise to lock it.
Getting Started
Scan the QR code or search “Renpho Health” in the Apple App Store or Google
Play Store.
Short press the power button to turn the tape on.
The Bluetooth is not connected if the Bluetooth icon continuously flashes.
- Turn on Bluetooth and open the “Renpho Health” app.
- Turn on the tape using the power button and tap “Pair” on the app to connect the tape with the app.
- The Bluetooth icon will be solid once the connection is successful.
Measuring & Save
- Press the detach button to release the tape, and wrap it around the body part to be measured.
- Insert the locking pin into the tape receptacle, and press until a “click” sound is heard.
- Press and hold the retract button until the tape has fully tightened around the body part to be measured.
- The measurement data will be displayed on the screen. Press the unit button to alternate between units.
- Click the body part name(e.g. Thigh) to sync data on the app.
- Choose the date.
- Press on the tape or click on the app to complete the measurement.
- Click “Save’ to keep a record of the data.
- Press the detach button to unlock the tape and press the retract button to reel in the tape.
Note:
- DO NOT allow the tape to retract too fast as minor injury may occur otherwise.
- DO NOT use excessive force to pull the tape (over 1 m/39.4 inch per second) as this may cause inaccurate readings.
Troubleshooting Guide
| Problems | Causes | Solutions |
|---|---|---|
| Ambiguous or no display | No battery or incorrect installation of battery |
Reinstall or replace the battery
A sudden change of display when the tape hasn’t been released| Brought by
strong vibration or violent shaking| Reset the display before releasing the
tape for measuring
Unusual number flashing or stuck display| Internal malfunction| Remove the
battery and reinstall again
FCC Regulatory Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Warning: Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
ISED Regulatory compliance This device contains license-exempt transmitters
that comply with Innovation, Science, and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following two conditions:
(1)This device may not cause interference. (2)This device must accept any
interference, including interference that may cause undesired operation of the
device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
Warranty Policy
Your RENPHO product purchase is covered by a one-year limited manufacturer
warranty from the date of delivery. For warranty terms and conditions, please
visit: https://renpho.com/pages/warranty-terms-and-conditions
Note: Product registration is not required for the warranty. If you choose
not to register your product, it will not diminish the product warranty.
Customer Service
Please feel free to contact us if you have any questions or concerns. RENPHO Customer Service Team guarantees a quick response and hassle-free solutions to any issue you may have within business hours.
TEL: +1(844) 417 0149 (US ONLY) Monday-Friday 9:00 AM-4:30 PM 1800 MY
RENPHO (1800 69 7367) (AU ONLY) Monday-Friday 9:OOAM-6:OOPM (AEST)
Email:support@renpho.com (US&CA)
support-au@renpho.com (AU)
*For defective products or the return of items, please contact us with your
order number within the specified warranty period.
DO NOT dispose of any product parts as they may be required for
inspection/repair.
US Importer: JOICOM CORPORATION 14129 The Merge Street,
Building 3 Unit A, Eastvale, CA 92880
Manufacturer: Shenzhen Ruiyi Business Technology Co., Ltd.
Qianhai Complex A201,
Qianwan Road 1, Qianhai Shenzhen-Hong Kong Cooperation Zone, Shenzhen,
P.R.China
Made in China NA1
Documents / Resources
|
RENPHO Smart Body Tape Measure
2
[pdf] User Manual
RY001, 2A26P-RY001, 2A26PRY001, Smart Body Tape Measure 2, Smart Body Tape
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>