OWL TC-ZTING01 True Wireless Earbuds Instructions
- June 5, 2024
- OWL
Table of Contents
OWL TC-ZTING01 True Wireless Earbuds
HOW TO USE
Open the charging compartment, wait for the green/orange light to go out, and the headset prompts that the pairing is successful. Open the charging compartment, wait for the green/orange light to go out, and the headset prompts that the pairing is successful. The earphones can be used individually or in pairs. In the state of playing music, touch the middle of the earphone handle with your hand, and the music sound of the music will change from small to large, and the volume can be controlled in a total of 16 levels Pinch 1.5S to play music, then pinch 1.5S to pause the music To answer the incoming call, tap 1S, and tap 1S to turn off the phone. In hearing aid/assisted hearing mode, the 3S earphone has a prompt volume sound, indicating that the hearing aid auxiliary mode is turned on, and at the same time, the music can be played or paused without affecting the hearing aid functions the hearing aid mode, the music volume can be adjusted.You can use APP to pair earphones to adjust the effect of hearing aid magnification and adapt to different groups of people.
PROMPT TONE
Key pattern| Function| functional operation| LED
indicate
| voice prompt
---|---|---|---|---
MFB
|
Power on
|
open a position
| The green light goes out|
POWER ON
Power off
|
Warehousing
| Green light out|
POWER OFF
Match
|
Warehouse Entry/Exit
| Green light out|
ONE TWO
Hearing Aid Mode|
Default
|
NA
|
Pure Bluetooth mode|
Touch &Hold 3s
|
NA
|
The beep goes on twice
Answerin g calls|
Short Press
|
NA
|
One beep
hang up| Long press 1s/ double click| NA| One beep
Decline calls|
Long press 1 NA
|
NA
|
One beep
play music|
Long press 1.5s
|
NA
|
One beep
Pause| Long press 1.5s| NA| One beep
V+/V-
|
volume plus
| Double click for 0.5s / hearing aid volume plus one level, a total of 6 levels, the volume is cycled from high to low|
NA
|
Beep。。。。
HEARING AID SPECIFICATIONS
Hearing aid specificatio ns
| sensitivity of a pickup| -38dB
---|---|---
Pickup distance| 3-5m
Pickup noise suppression| -60db
Howling suppression ratio| -40db
Pickup gain| -30db
Pickup frequency| 125HZ-10KHZ
BLUETOOTH SPECIFICATIONS
Bluetooth specifications
| DSP| QC9864BT
---|---|---
Bluetooth version| 5.1
Fraquency range| 2.402GHz-2.480GHz
ransmission distance (unobstructed)|
≤15meter
Track system| Stereo
Output specifications
| Speaker Impedance| 32Ω/Ф10mm
Audio Power Output(Max)| 135mW
Headphones Sensitivity| 120dB
Fraquency range| 20HZ-20KHZ
distortion factor| ＜1%
SNR| ≥90dB
Depth of call noise reduction|
adjustable0-30dB
EARPHONE SPECIFICATIONS
GENERAL WARNING
In order to ensure your personal safety and the correct use of hearing aids,
you should be familiar with the general warnings. Please note that hearing
aids cannot restore normal hearing, nor will it prevent or improve hearing
damage caused by organic diseases. In most cases, hearing aids are not used
frequently. Please pay attention to the wearing guidelines. If there is an
accident in your ears, please consult a hearing consultant.
Dysfunction
Be wary that hearing aids may stop working without prompting. If you need to
rely on hearing to make certain judgments (such as in traffic), keep this in
mind. Hearing aids may stop working, for example, if the battery has expired
and the battery runs out , Or the component is damaged.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>