Suncast Corporation BMEB2000 Series Backyard Oasis Entertainment Pull Out Drawers and Shelving Space User Manual

: May 15, 2024
: Suncast Corporation

Table of Contents

BMEB2000 Series Backyard Oasis Entertainment Pull Out Drawers and
Specifications:
Product Usage Instructions:
Description:
Before You Begin:
Cautions:
Care Instructions:
Parts:
Assembly:
Moving the Product:
Electric Cord Routing:
- FAQ:
Q: Do I need to register my product for warranty?
Q: How do I purchase replacement parts for the bar?

BMEB2000 Series Backyard Oasis Entertainment Pull Out Drawers and

Shelving Space

“`html

Specifications:

Product Name: BMEB2000 Series Backyard Oasis Entertaining
Bar
Manufacturer: Suncast Corporation
Model Number: BMEB2000
Assembly Required: Yes
Material: Steel, Plastic

Product Usage Instructions:

Description:

The BMEB2000 Series Backyard Oasis Entertaining Bar is a stylish
and functional outdoor bar designed for hosting gatherings and
parties in your backyard.

Before You Begin:

Make sure you have all the necessary tools and parts listed in
the manual before starting the assembly process.

Cautions:

Handle all parts with care to avoid damage. Follow the assembly
instructions carefully to ensure proper construction.

Care Instructions:

Regularly clean the bar with a mild soap and water solution.
Avoid using harsh chemicals that may damage the finish.

Parts:

Refer to the manual for detailed part numbers and descriptions
to identify each component correctly before assembly.

Assembly:

Follow the step-by-step assembly instructions provided in the
manual, starting from pre-assembly of drawers to the final
installation of footrests, shelves, doors, and other
components.

Moving the Product:

Exercise caution when moving the assembled bar to ensure
stability and prevent any damage. Enlist the help of others if
needed.

Electric Cord Routing:

Properly route and secure any electric cords to prevent tripping
hazards and ensure a neat appearance.

FAQ:

Q: Do I need to register my product for warranty?

A: Yes, you must register your product within 90 days of
purchase to avail of the limited warranty. Refer to the manual for
registration details.

Q: How do I purchase replacement parts for the bar?

A: You can visit the manufacturer’s website or contact customer
support for information on purchasing Suncast replacement
parts.

“`

BMEB2000 Series Backyard Oasis Entertaining Bar
ASSEMBLY INSTRUCTIONS
Tools Required

Brilliant
by Design’ un

Scan QR Code for product assembly video.
C) 2023 Suncast Corporation, Batavia, IL

0361696

Register your product for Limited Warranty!
Must register product within 90 days of purchase for limited warranty
Scan for updated Limited Warranty
www.suncast.com/warranty or call US 1 800-846-2345
Have Questions?
We are here to help. Check out our resource library along with helpful tips, videos and FAQ’s at https://support.suncast.com
You may call the Contact Center directly at: 1 800-846-2345 or write Suncast Corporation, Contact Center, 701 N. Kirk Road, Batavia, IL 60510 (USA)

To purchase Suncast replacement parts and learn about other Suncast products visit us online or call.

www.suncastcom 1-800-846-2345 or 1-630-381-6309.

Table of Contents
Description
Before You Begin
Cautions
Care Instructions Parts
Panels Steel Drawers and Sand Containers Inserts and Accessories Hardware
Pre-Assembly Drawers Drawer Glides Cabinet Floor Bottom Drawer Glides Door Handle Shelf Front Panels Bar Top Cord Slide Sand Containers Footrest Cap
Assembly Floor, Side and Front Panels Toe Kicks Sand Containers Cabinet Floor Bar Top Supports Bar Top Dividers Door Trim Counter Top Footrest Shelf, Door and Drawers Grommet
Moving the Product
Electric Cord Routing
3

Page
4
4
4
5 6 8 9 10
11 15 17 18 19 19 20 21 22 23 23
24 26 27 27 28 29 32 33 33 35 36 39
40
42

A Before You Begin…
· Read instructions thoroughly prior to assembly. This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence.
· Please verify parts. Verify all parts and quantities indicated in this manual are present before beginning assembly.
· Please follow instructions. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly. · ·
· Assistance is required during portions of assembly. pliq
A Cautions
· The finished product must be placed on aflat and level surface. Failure to do so may void the warranty. · DO NOT use product without sand containers filled and installed. · The finished product is very heavy. Only move the product as described in ‘ Moving the Product’ at
the end of this manual. · The final assembly of this product should take place at or near the desired location for use. Pre-assembly
steps can be completed in other available spaces. Refer to the table of contents for related steps. · DO NOT exceed the following weight capacities:
Bar Top – 150 lbs (68 Kg) Counter Top – 150 lbs (68 Kg) Small Drawers – 10 lbs (4.5 Kg) Large Drawers – 50 lbs (22.7 Kg) Foot Rail – 150 lbs (68 Kg) · DO NOT stand or sit on the bar surfaces or footrest. · DO NOT store or rest hot items (i.e., grill tools, portable heaters, etc.) in drawers or on bar surfaces. · Product not for storage of flammable or caustic chemicals. · Store heavy items near the bottom of product. · Product not intended for use by children. · Repair or replace broken parts immediately. · Suncast is not responsible for damage caused by weather or misuse. · At regular intervals, inspect the product to make sure that assembly integrity has been maintained. · This kit contains parts with metal edges. Please be careful and use gloves when handling.
Care Instructions
· To maintain the look of your product, we recommend cleaning it at regular intervals with mild soap and water. DO NOT use bleach, ammonia or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to perform cleaning at regular intervals could result in permanent staining of the plastic. This type of damage is not covered under warranty.
4

Parts – Panels

OB00818 Bar Top

OB00817 Counter Top

01, OB00800
Right Side Panel

o
OB00809 Right Divider

o
OB00811 Shelf

CO–
OB00812 Door

OB00810 Door Trim

OB00807 Cabinet Floor

OB00799 Left Side Panel

OB00803 Right Front Panel
OB00802 Middle Front Panel

OB00808 Left Divider

OB00801 Left Front Panel

OB00806 Right Toe Kick

OB00798 Floor Panel

OB00804 Left Toe Kick
OB00805 Middle Toe Kick

Parts – Steel
o

o
Ó
o

0280665 Footrest

OMR007006A
S- Rail – 15″ x2

(ID elD

OMR007008A S- Rail – 47.5″

OMR007020 S- Rail – 70″

o
(:) 1MR005020 Truss Leg x4

BB
1MRG09022 Angle Bracket
x2

OMP000056 Bar Top Support
x3

OMP000044A

Angle Supports

0
r I
0

OMP000055
Upper Footrest Bracket x4

OMR002020 Header Beam
x2

OMR004020 Side Adapter
x3

OMP000004 Support Brace
x6
7

OMP000054 Lower Footrest Bracket
x4

Parts – Inserts and Accessories

0102552 Cord Slide
ci
0511011 Grommet

010097610 Handle x5

0240075 Footrest End Cap
x2

J,
0511015 Sand Container Cap
x3

Parts – Hardware
0671306 – Hardware Bag

063 146 1/4-20 x1.75″ Phillips Screw
x6

0631457 1/4-20 x2″
Carriage Bolt x4

0671307 – Hardware Bag

0632537 1/4-20 x5/8″ Carriage Bolt
x36

0632526 1/4 x1″ Flat Washer
x40

0631732 1/4-20 Lock Nut
x46

0671308 – Hardware Bag

e
*Hex Key – 4mm

(iD

0632448

0632449

Screw Insert #8-32 x . 5″

x40

Phillips Head Screw

x40

Hardware shown at actual size (* Unless otherwise noted.) Extra hardware provided. Not all are used.
10

0630970 #10 x5/8″ Phillips Head Cap Screw
x230

Pre-Assembly – Drawers

This product uses self-tapping screws in some areas. There are no pre-drilled holes. Use force when

starting to drive the screw. Once the screw pierces the plastic it will drive easier.

Using the included 4mm Hex Key, insert screw insert (SS) into right side panel (C), left side panel (B), right divider (L), left divider (K) and

small drawer boxes (S).

Refer to panel threaded nut locations shown below.

NOTE: Some pressure is required to start the screw insert (SS) into the plastic panels. Tighten until flush with the panel surface. Do not overtighten.

(SS) x30

i MN
s

· 1[01

g ”

[01

M’s

·7,

·7.

sal

Pre-Assembly – Drawers (cont.)
With the smooth side of the drawer facing up, fold the left and right sides of one small drawer (S) upward toward the center of the drawer. Fold the back of the drawer up to engage the side tabs. The tabs must be securely snapped through the back corner slots.
HINT: It may be helpful to lower the back of the drawer box to the floor and tip the drawer sides into the back corner slots of the drawer.

Repeat to assemble the remaining small drawer (S) and two large drawers (U).
12

Slide the slots in one small drawer front (R) onto the tabs on the front of one formed small drawer (S). Slide until the front panel snaps into place. From the bottom of the small drawer (S), insert two screws ( II) through the small drawer securing it to the drawer front (R). Repeat to assemble the remaining small drawer front (R) to small drawer (S).
(TT) x4

Insert one drawer handle (W) on an angle into the top edge of the handle hole of one small drawer front (R). Rotate the bottom of the handle toward the drawer front and press firmly on the center of the handle to snap it into place.
Repeat with one handle into the remaining small drawer front (R).

d
x2

Pre-Assembly – Drawers (cont.)
oSlide the slots in one large drawer front (T) onto the tabs on the front of one formed large drawer (U). Slide until the front panel snaps into place. From the bottom of the large drawer (U), insert three screws (TT) through the large drawer securing it to the drawer front (T). Repeat to assemble the remaining large drawer front (T) to large drawer (U).
(TT) x6 NOTE: Using aPhillips head screwdriver or other similar tool, pierce the six holes indicated in the bottom of the large drawer (U).
o
Insert one drawer handle (W) on an angle into the top edge of the handle hole of one large drawer front (T). Rotate the bottom of the handle toward the drawer front and press firmly on the center of the handle to snap it into place. Repeat with one handle into the remaining large drawer front (T).
14

Pre-Assembly – Drawer Glides
oSeparate the drawer glides (X) into two parts, the wide base and the narrow glide. a) extend the narrow glide fully. b) lift upward on the glide catch and slide the narrow glide out from the wide base. Repeat for the remaining three drawer glides (X).
Assemble the narrow glide portions to the small drawers (S) using three screws each (UU) . NOTE: Be sure to orient the bent end of the narrow glide portions toward the front of the drawers.
(UU) x12
15

Pre-Assembly – Drawer Glides (cont.)
Attach one drawer glide wide base to the right side panel (C) with three screws (UU). NOTE: The rubber bumper-stops should be oriented toward the back of the side panel (C). To access the front two screw locations, line up slots in the moving part of the wide base with the mounting holes. Repeat for the left side panel (B) and one additional drawer glide wide base.

(UU) x6

Attach one drawer glide wide base to the right divider panel (L) with three screws (UU). NOTE: The rubber bumper-stops should be oriented toward the back of the divider panel (L). To access the front two screw locations, line up slots in the moving part of the wide base with the mounting holes. Repeat for the left divider panel (K) and one additional drawer glide wide base.
(UU) x6
16

Pre-Assembly – Cabinet Floor
Using four screws each ( II), attach two header beams (Z) to the underside of the cabinet floor panel (J).
[TI (TT) x8

Using 12 screws each ( II), attach two truss legs (AA) to the underside of the cabinet floor panel (J). IMPORTANT: Orientation of the truss legs (M) is important. Be sure to orient the truss legs with the ends having two holes (**) positioned at the end of the cabinet floor panel (J) as shown.
V
lip x24
V V

(TT) x24

<aï —
3> «2j9 `a eee>

<2> <2> <2

[2 .

Pre-Assembly – Bottom Drawer Glides

Flip the cabinet floor (J) so the smooth side is facing up. Using two bolts (VV), washers (WW) and nuts (XX), attach one large drawer glide (Y) to the cabinet floor.

hmi

Repeat for the three remaining large drawer glides (Y).

NOTE: The large drawer glide (Y) needs to be extended to access mounting holes (aa) prior to attaching to the cabinet floor.

CAUTION: Collapse large drawer glides (Y) before attempting to move the cabinet floor (J) after assembly.

HINT: Tape the drawer glides closed to avoid glides opening while moving later in the installation.

(VV) x8 (WW) x8

(XX) x8

Pre-Assembly – Door Handle
Insert one drawer handle (W) on an angle into the top edge of the handle hole of the door (M). Rotate the bottom of the handle toward door front and press firmly on the center of the handle to snap it into place.

Pre-Assembly – Shelf

CE1

Using four screws each ( II), attach two angle brackets (BB) to the bottom of the shelf (Q).

Pre-Assembly – Front Panels
Using ten screws ( II), attach one side adapter (CC) to middle front panel (E). Repeat for the left front panel (D) and right front panel (F) at locations indicated below.
(TT) x30
Using three bolts (VV), washers (WW) and nuts (XX), attach one upper footrest bracket (DD) and one lower footrest bracket (EE) to the left front panel (D). Tighten the bolts securely. NOTE: Holes may need to be pierced prior to installing bolts (VV). Pierce holes from the front side of panels. Repeat to install the remaining three upper footrest brackets (DD) and lower footrest brackets (EE) onto the middle front panel (E) and right front panel (F). See locations below for reference.
0 .-w
20

x10
(VV) x12 (WW) x12 (XX) x12

Pre-Assembly – Bar Top
IMPORTANT: Be sure to use the correct size S- Rails for each of the steps as described below.
Using five screws each ( II), attach two 15″ S- Rails (FF) to the underside of the bar top (P). [.. IMPORTANT: Be sure the S- Rails sit fully into their respective recessed channels. Press down continuously on the S- Rails as the screws are installed.

Using seven screws each ( II), attach one 47.5″ S- Rail (GG) and one 70″ S- Rails (HH) to the underside of the bar top (P). IMPORTANT: Be sure the S- Rails sit fully into their respective recessed channels. Press down continuously on the S- Rails as the screws are installed.
Ox14

Tr) x14

Pre-Assembly – Bar Top (Cont.)
Using six screws each ( II), attach three bar top supports (JJ) to the underside of the bar top (P) at the locations shown. NOTE: The bar top support (JJ) mounting holes will align with the screw recesses in the underside of the bar top (P).

–

Ox18

5ne

[ED x18

111

Pre-Assembly – Cord Slide
El) Attach the cord slide (KK) to the left side panel (B) using one screw ( II) and washer (WW). NOTE: Do not overtighten the screw ( II). The cord slide (KK) should easily slide back and forth without much resistance.
(WW)xl
22

Pre-Assembly – Sand Containers
Using afunnel, fill the sand containers (V) with sand or pea gravel. Install the sand container caps (RR) securely. CAUTION: Do not fill sand containers to alevel more than shown or to an approximate weight of 30 lbs. (13.6 kg). Once the sand containers are filled and capped, lay them on their side to evenly distribute the sand prior to installation.

Pre-Assembly – Footrest Cap

Insert one footrest cap (PP) into each end of the footrest (00). If needed, use arubber mallet to fully set the footrest caps.

Assembly – Floor, Side & Front Panels
REMINDER: Final assembly of this product should take place at or near the desired location for use.
Insert the bottom tabs of the left side panel (B) into the side slots of the floor panel (A). While pressing downward, slide the left side panel toward the front of the floor panel. Lift slightly on the left side panel to confirm the panel has fully engaged the floor panel.
Repeat the process to assemble the right side panel (C) to the floor panel (A).

O
o

Align the three slots in the left front panel (D) with the tabs on the left side panel (B).
Slide the left front panel downward while inserting the tabs of the left front panel into the slots in the floor panel (A). Press the left front panel downward firmly to lock the tabs.

NOTE: The tabs should snap when locked.

hui

Align the three slots on the right front panel (F) with the tabs on the right side panel (C).
Slide the right front panel downward while inserting the tabs of the right front panel into the slots in the floor panel (A). Press the right front panel downward firmly to lock the tabs.
NOTE: The tabs should snap when locked.
hmi

lea

Align the middle front panel (E) with the left and right front panels (D, F). Snap the tabs of the middle front panel into the slots in the floor panel (A). Press the middle front panel downward firmly to lock the tabs.

NOTE: The tabs should snap when locked.

Secure the left and right front panels (D, F) to the middle front panel (E) using 14 screws ( II).

(TT) x14

Assembly – Toe Kicks

Insert the side tab of the right toe kick (I) into the slot on the inside of the right side panel (C). 2) Slide the right toe kick down while inserting the bottom tabs into the locking slots in the floor panel (A). NOTE: Press the right toe kick (I) downward firmly to lock the tabs. The tabs should snap when locked. Repeat the process to assemble the left toe kick (G) to the left side panel (B) and floor panel (A).
Using four screws ( II), secure the middle toe kick to the right and left toe kicks (G, I) . (TT) x4
x4
26

Assembly – Sand Containers
IMPORTANT: Do not use this product without the sand containers filled and properly placed in the base. NOTE: Be sure the product is located in the desired location for use prior to inserting the sand containers (V) into the base. Place filled sand containers (V) into the base as shown. The sand containers should be positioned against the front panels (D, E, F).
el%
geJ
%It

Assembly – Cabinet Floor

With the drawer glides (Y) facing up, slide the cabinet floor (J) into position over the toe kicks (G, H, I) and against the front panels (D, E, F). Lower the rear edge of the cabinet floor (J) until it locks into the side panels (B, C).

CAUTION: Be careful of the installed drawer glides (Y) while moving the cabinet floor (J).

hmi

Assembly – Cabinet Floor (Cont.)
ED Using ten screws ( II), secure the cabinet floor to the right and left side panels (B, C) as well as the front panels (D, E, F).
(TT) x10

Assembly – Bar Top Supports

Using three screws each (UU), secure two angle supports (LL) to the right side panel (C).

Repeat the process to secure two additional angle supports (LL) to the left side panel (B).

(

(UU) x12

Assembly – Bar Top
With the help of another person, position the bar top (P) over the front panels (D, E, F) and bar top angle brackets (LL). NOTE: Be sure the three bar top supports (JJ) (shown for clarity) align with the cutouts at the top of the front panels (D, E, F).
hmi

Install one bolt (ZZ) and nut (XX) through one bar top support (JJ) and front panel side adapter (CC) connection. Tighten the bolt and nut securely.

Repeat the process for the remaining two bar top supports (JJ) to the front panel side adapters (CC).

(ZZ) x3

(XX) x3

Assembly – Bar Top (Cont.)
Install one support brace (MM) to both sides of one bar top support (JJ) and front panel side adapter (CC) using one bolt (ZZ) and one nut (XX). Leave the bolt and nut loose at this time allowing the support braces (MM) to hang freely. Secure the bottoms of the support braces (MM) to the front panel side adapter (CC) using two screws ( II). After the screws are secured to the front panel side adapter, tighten the previously installed bolt (ZZ) and nut (XX) securely. Repeat the process for the remaining two bar top supports (JJ) to the front panel side adapters (CC).

(ZZ) x3

(XX) x3

(TT) x6

Eil

Using three screws each ( II), secure the bar top (P) to each of the four angle support (LL).

(TT) x12

cç

x12
30

Using six screws ( II ) secure the bar top (P) to the front panels (D, E, F). (TT) x6
31

Assembly – Dividers

Align the side tabs of the left divider panel (K) with the slots in the left front panel (D). 2) Slide the left divider panel downward while inserting the bottom tabs of the right divider panel into the slots in the
cabinet floor (J). NOTE: Press the left divider panel (K) downward firmly to lock the tabs. The tabs should snap when locked. Repeat the process to install the right divider panel (L) to the right front panel (F) and cabinet floor (J).
32

Assembly – Door Trim
Insert the side tabs of the door trim (N) into the slots in the left and right divider panels (K, L). NOTE: Be sure the top of the door trim (N) is flush with the tops of the left and right divider panels (K, L).
Assembly – Counter Top
Place two truss legs (M) into the top slots across the left and right side panels (B, C) and dividers (K, L). Be sure the truss legs lay flush with the tops of the left and right side panels and dividers. IMPORTANT: Orientation of the truss legs (M) is important. Be sure to orient the truss legs with the ends having two holes (**) positioned at the end over the right side panel (C) as shown.
33

With the help of another person, position the counter top (0) over the left and right side panels (B, C) and dividers (K, L). Align the slots on the underside of the counter top with the top tabs of the left and right side panels and dividers. Lower the counter top onto the tabs and slide the counter top forward to contact the front panels (D, E, F).
hmi

IMPORTANT: Be sure all slots and tabs are engaged before sliding the counter top.

ffl (Effl
,fflfflfflffla fflfflfflfflffl , ffl /ffl F11
ffl 1E1 fffl

ff,l1 I

-aaaaa

^ilfflfflfflfflffl

SIffltEfflffl

-ilfflfflfflfflffl

fflfflliEfflffl’

ffl a
_ataaffler ) aaas& EfflfflfflffltErtS1fflfflfflfflL EtElfflfflfflfflalffltEifflfflffl
fflfflfflffliElp ,> aeastata —
Sfflfflfflffl ,, ffll”

aaE

Afflffle ‘.f_·.-fflfflfflfflISESIfflIEfflEE Sfflfflfflfflfflfflfflfflfflfflffl StElfflfflfflfflfflfflfflfflffl17

ffl 1ffl ”

ffl ffl

Rffl-

afflI1jr,

ffla

Secure the counter top (0) to the two truss legs (AA) using 24 screws (TT).
Secure the counter top (0) to the front panels (D, E, F) using 4screws (TT).

(7)x28

Assembly – Footrest
Carefully slide the footrest (00) through the large open areas at the rear of the footrest brackets (DD, EE). Once positioned through the four footrest brackets, move the footrest forward to align the mounting holes in the footrest with the holes in the footrest brackets.

CAUTION: Be sure to slide footrest through the largest opening of the brackets to avoid scratching the footrest.

Secure the footrest (00) to one footrest bracket (DD, EE) using one bolt (MA), washer (WW) and nut (XX). Tighten the nut securely. Do not overtighten.
Repeat for the remaining 3footrest brackets (DD, EE).
Insert one footrest cap (PP) into each end of the footrest (00). If needed, use arubber mallet to fully set the footrest caps.

(AM) x4

r
(XX) x4

(WW) x4

o o
Am, x4tje cD’
o x4CC-3

Assembly – Shelf, Door & Drawers
While holding the shelf (Q) at aslight angle, slide the shelf between the left and right dividers panels (K, L) toward the front panels.Once fully inserted, tilt the shelf level and lower the shelf into position onto the shelf rails molded into the divider panels.
NOTE: The shelf (Q) should snap into position. Be sure the side tabs on either side of the shelf engage with the slots in the shelf rails.
36

Position the left post of the door (M) into the glide slot located near the top of the left divider panel (K). While maintaining the post location, pivot the right side of the door upward until the right post of the door snaps into the glide slot located near the top of the right divider panel (L). Once fully engaged with divider panels (K, L), pivot the door downward into its closed position.
37

Assembly – Shelf, Door St Drawers (Cont.)
Fully extend the pair of large drawer glides (Y) installed on the left side of the cabinet floor (J) (remove tape if used). Position one large drawer assembly (U, T) onto the extended large drawer glides (Y). Align the mounting holes in the bottom of the drawer assembly with the holes in the large drawer glides. NOTE: If not already done, pierce the six holes in the bottom of the large drawer (U) using aPhillips head screwdriver or other similar tool.
Secure the large drawer assembly (U, T) to the large drawer glides (Y) using six bolts (VV), washers (WW) and nuts (XX). Tighten securely. Do not overtighten. Repeat steps 48 and 49 to install the remaining large drawer assembly (U, T) to the large drawer glides (Y) installed on the right side of the cabinet floor (J) (remove tape if used).
(VV) x12
(XX) x12
38

Fully extend the small drawer glides on the left side panel (B) and left divider panel (K).

Align the inner glides of one small drawer assembly (S, R) to the small drawer glides. Insert the drawer inner glides into the extended glides then insert the small drawer assembly fully into the cabinet.

NOTE: Once the small drawer assembly is inserted, pull the drawer out

to confirm the drawer stops at full extension.

Repeat the process to install the remaining drawer assembly (S, R) to the remaining small drawer glides on the right side panel (C) and right divider panel (L).

Assembly – Grommet

Insert the grommet (QQ) into the large hole in the counter top (0). Be sure to fully seat the grommet.

Assembly complete.
39

Moving the Product

X**CAUTION: The finished product is very heavy. DO NOT LIFT WITH THE FOOTREST, BAR I,t TOP OR COUNTER TOP. Moving the finished product should be done with two or more people. Excessive stress or twisting can damage to the product and can void the warranty. REMOVE SAND CONTAINERS AND STORED ITEMS PRIOR TO MOVING. REPLACE SAND CONTAINERS AFTER PRODUCT HAS BEEN RELOCATED.

To remove the sand containers (V), remove the four screws ( II) securing the middle toe kick (H) and remove the middle toe kick. Carefully reach into the base to pull out the sand containers.

To replace the sand containers, slide two sand containers to the left and right of the base followed by the remaining sand container in the center. The sand containers should be positioned against the front panels (D, E, F) as shown.

[

(TT) x4

If moving the product for short distances on asmooth surface, the product can be carefully slid by pushing on the bottom corners of the side panels (B, C).
If the product is to be moved for long distances and/or over uneven surfaces, it is recommended to place moving dollys under each end of the product before moving. Lift carefully from the floor panel (A) to place on dollys.
41

Electric Cord Routing
Electrical cords can be routed downward through the grommet hole, along the bar corner and out the cord slide. Remove the grommet (QQ) and open the cord slide (KK). Feed the electrical cord through the grommet hole down along the bar corner and behind the drawers and feed the cord plug out of the cord slide hole in the right side panel (B). Positing the cord into the cord cutout and slide the cord slide closed. HINT: Removing the small drawer and pulling out the large drawer may help in routing acord along the bar corner.
km*
42

References

Suncast Limited Warranty Information - Suncast® Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format) >>

Download This Manual (PDF format)

Download this manual >>