Kinglucky X7 Bone Conductive Headphone User Manual
- June 4, 2024
- KingLucky
Table of Contents
Kinglucky X7 Bone Conductive Headphone
Product Graphic and Accessories
- Power ON/OFF &Volume Down
- Volume up
- Microphone
- Indicator
- USB Charging port
Accessories List
- X7 bone conductive headphone
- USB charging cable
- Instruction manual
Directions To Use X7 Headphone
Power On
To press the power button for 2 seconds tell the LED indicator blinks RED and
BLUE alternately, the headphone is turned on and ready for Bluetooth
connection.
Bluetooth Connection
At the first time to use, after the headphone is turned on, itwill be searched
in the Bluetooth settngs mode of your devices (mobile phone or music player).
Then you will find “X7” and select it in your Bluetooth devices found. When X7
is connected success, the blue indicator will blink slowly and when music
playing, the indicator will be turned off.
Paired Device Replacement
Disconnect the Bluetooth of your current paired device, then the headphone
indicator will blink RED and BLUE alternately again. Other devices can find
“X7” and available for connection.
Power Off
To press the power button for 3 seconds to turn off the headphone.It also can
be shut down automatically if there is no pairing or connection for 180
seconds.
Low Power Alarm & Charging
Normally the mobile phone will display the headphone power status. If the
battery voltage is lower than 3.4V, you will hear the low power alarm for
every 120 seconds. Once the battery voltage dropped to 3.2V, headphone will be
turned off automatically. Then please use the USB cable to plug into power
adaptor for charging.
Operation Instruction
POWER ON/OFF, VOLUME DOWN
- Push the button for 2 seconds to turn on
- Push the button for 3 seconds to turn off
- Double clicks for next song
- Triple clicks for Volume Down
VOLUME UP
To play music:
- Click for Play/Pause
- Double clicks tor previous song
- Triple clicks for volume up (Beep sound when reach the max. volume)
- Push the button for 2 seconds to call Al assistant (like “siri'”) To answer the call
- Click for calling answer
- Push button for 2 seconds to dismiss the call
- Click for conversation ended
- Double cicks to end the call and answer third party call
Indicators Description
- Alternate RED and BLUE: waiting for pairing
- BLUE for 3 seconds then turned off: Bluetooth connected
- RED: under power charging
- BLUE: battery is fully charged
Product Specification
- Model name: X7
- Bluetooth version: 5.0
- Net weight: 31.58
- Battery capacity: 320mAH
- Power input: 5V1A
- Battery charging time: 2 hours
- Music playback: 12 hours at 70% volume
- Waterproof: IP55
- Transmission distance: 10 meters
- Protocol support: A2DP,AVRCP,HSP,HFP
Trouble Shooting
- Unable to turn on headphone
- Please make sure the battery was fully charged and power button was pressed on right position.
- Unable to connect headphone
- Please make sure the indicator LED is on the status of RED and BLUE blinking alternately. If the indicator blink BLUE Slowly, the headphone was connected by other device. Please disconnect the device and try again.
- Unable to reconnect headphone
- please make sure Bluetooth on your device was turned on.
- Less transmission distance
- Please make sure your Bluetooth version of device is 4.0 above. The old version Bluetooth may cause shorter transmission distance.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.