KRAMER DSP-62-UC 2xHDMI to HDBaseT Switcher User Guide
- June 5, 2024
- Kramer
Table of Contents
KRAMER DSP-62-UC 2xHDMI to HDBaseT Switcher
DSP-62-UC Quick Start Guide
This guide helps you install and use your DSP-62-UC for the first time. Go to www.kramerav.com/downloads/DSP-62-UC to download the latest user manual and check if firmware upgrades are available.
Check what’s in the box
- DSP-62-UC Digital Sound Processor
- 4 Rubber feet 1
- Quick start guide
- Power adapter and cord 2
- Bracket sets
Get to know your DSP-62-UC
| # | Feature | Function |
|---|
1
| SETUP DIP-switches| Do not change DIP-switch settings (not for use)!
DIP-switches 1 and 2 are always set to ON (down) and DIP-switches 3 and 4 are always set to OFF (up).
2| HDMI IN 1 Button| Press to select HDMI IN 1 input (on the front panel).
3| HDMI IN 2 Button| Press to select HDMI IN 2 input (on the rear panel).
4| AUDIO LEDs| USB IN| Lights green when an audio source is received from the
USB host port.
USB OUT| Lights green when an audio signal is sent to the USB host port.
5| IN (1 to 5)| Lights green when a signal is present, lights red when
clipping is detected. For IN 2 to IN 5, when connecting a microphone and
setting to Mic mode via the embedded web pages, lights blue.
OUT 1| Lights green when a signal is present, lights red when clipping is
detected.
6| AUDIO IN 1 3.5mm Mini Jack| Connect to an unbalanced audio source.
7| USB Type B Bi-directional Host Port| Connect to an audio source or
acceptor.
8| HDMI IN 1 Connector| Connect to an HDMI source.
9| LINK LED| Lights green when a link with the receiver is established.
10| ON LED| Lights green when the device is powered by power supply. Lights
blue when provides PoE (PSE).
Lights orange when powered by PoE (PD).
11| HDMI IN 2 Connector| Connect to an HDMI source.
12| HDBT OUT Connector with POE (PD & PSE)| Connect to an HDBT receiver.
13| AUDIO IN 3-pin Terminal Block Connectors (2 to 5)| Connect to up to 4 mono
balanced audio sources (mono or mic level with selectable 48V).
14| AUDIO OUT 5-pin Terminal Block Connector| Connect to a stereo balanced
audio acceptor.
15| I/O Terminal Block Connectors (1 to 2)| Connect to up to two sensors,
switches, LEDs, or relays.
16| RS-232 (G, Rx, Tx) Terminal Block Connector| Connect to a PC/serial
controller
17| ETHERNET RJ-45 Connector| Connect to a PC via a LAN.
18| RESET Recessed Button| Press and hold while powering the device to reset
to factory default values, including IP settings.
19| 48V DC Power Connector| Connect to the power supply and to the mains
electricity.
Mount DSP-62-UC
Install DSP-62-UC using one of the following methods:
- Attach the rubber feet and place the unit on a flat surface.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/DSP-62-UC).
- Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/DSP-62-UC).
- Mount the unit in a Kramer Table-Mount unit (see www.kramerav.com/product/DSP-62-UC).
Connect inputs and outputs
Connecting the audio output
- To a balanced stereo audio acceptor
- To an unbalanced stereo audio acceptor
Connect power
Connect the 48V DC power cord to DSP-62-UC and plug it into the mains
electricity (unless powered by PoE). Safety Instructions (See
www.kramerav.com for updated safety information)
Caution:
-
For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
-
There are no operator serviceable parts inside the unit.
Warning: -
Use only the power cord that is supplied with the unit.
-
Disconnect the power and unplug the unit from the wall before installing.
Operate the DSP-62-UC
Operate DSP-62-UC via:
- Embedded web pages via the Ethernet.
-
RS-232 serial commands are transmitted by a touch screen system, PC, or other serial controller.
RS-232 Control / Protocol 3000Baud Rate:| 115,200| Parity:| None
Data Bits:| 8| Command Format:| ASCII
Stop Bits:| 1| |
Example: (adjust analog audio output 1 to “-10dB”): #x-aud-lvl out.analog_audio.1.audio.1,-10
Default Ethernet Parameters (Set to DHCP ON)
Fallback IP Address:| 192.168.1.39| UDP Port #:| 50000
Subnet mask:| 255.255.0.0| TCP Port #:| 5000
Gateway:| 192.168.0.1| User/Password| Admin/Admin
Factory Reset
Recessed Button| Press and hold while powering the device.
Protocol 3000:| “#factory” command.
Web Pages:| In the Settings page, click Reset.
References
- Kramer | Audio-Visual Solutions and Experiences
- Kramer | Audio-Visual Solutions and Experiences
- Application Diagrams - Kramer Electronics
- kramerav.com/product/DSP-62-UC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>