MOKUNGIT S1-D1 AC Triac DMX Dimmer Instruction Manual
- June 3, 2024
- MOKUNGIT
Table of Contents
S1-D1 AC Triac DMX Dimmer
Instruction Manual
S1-D1 AC Triac DMX Dimmer
AC Triac DMX Dimmer
Model No.: S1-D1
- Channel/RDM/Stand-alone function/Leading edge or trailing edge/Numeric display/Din rail
Features
- AC phase-cut mosfet dimmer with DMX512 function, one channel output.
- Comply with the DMX512 standard protocols.
- Digital numeric display, set DMX decode start address by bottoms.
- RDM function can realize intercommunication between DMX master and decoder.
- Reverse-phase dimming or forward-phase dimming selectable.
- Minimum brightness set from 1% to 40%.
- Stand-alone dynamic mode and dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal.
- To dim and switch single color dimmable LED lamps, traditional incandescent and halogen lights.
- Overheat protection, recover automatically.
- Available in white or black.
Technical Parameters
Input and Output
| Input voltage | 100-240VAC |
|---|---|
| Output voltage | 100-240VAC |
| Output current | 1CH, 2A |
| Output power | 200-480W |
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Certification| CE,EMC,LVD
Dimming data
| Input signal | DMX512 |
|---|---|
| Dimming level | 256 levels |
| Dimming range | 0 -100% |
Environment
| Operation temperature | Ta: -30° C ~ +55°C |
|---|---|
| Case temperature (Max.) | T c: +85°C |
| IP rating | IP20 |
Warranty
| Warranty | 5 years |
|---|
Weight
| Gross weight | 0.130kg |
|---|---|
| Net weight | 0.160kg |
Compatible Load Types
| Load Type | Maximum Load | Remarks |
|---|---|---|
| Dimmable LED lamps | 300W @ 220V | |
| 150W @ 110V | Due to variety of LED lamp designs, maximum number of LED lamps |
is further dependent on power factor result when connected to dimmer.
Triac Dimmable
LED drivers| 300W @ 220V
150W @ 1 1 OV| Maximum permitted number of drivers is 300W divided by driver
nameplate power rating, and make sure the surge current is no more than 2
times 65A.
Incandescent lighting,
HV Halogen lamps| 500W @ 220V
250W @ 1 10V|
Mechanical Structures and Installations
Wiring Diagram
Caution:
Please carefully ensure all wire connections and polarities are correct and
secure before applying power, otherwise this controller will be damaged.
Note: When calculating the maximum number of load lamps or drivers, the
input power or input current parameters of a single lamp or driver must be
used, the output power parameters can not be used. In addition, the maximum
surge current of the dimmer is 65A, the sum of surge current of multiple
dimmable LED drivers should not exceed 2 times. otherwise, the product will be
overloaded and damaged.
Operation
System parameter setting
- Long press M and ◀ key for 2s, prepare for setup system parameter: control method, minimum brightness curve, default output level, automatic blank screen. short press M key to switch four item.
- Control method: short press ◀ or ▶ key to switch forward-phase(“C-F”) or reverse-phase(“C-R”).
- Minimum brightness: short press ◀ or ▶ key to set minimum brightness, from 1% to 40%(“b01″ to”b40”). You need set suitable minimum brightness to avoid
- Default output level: press ◀ or ▶ key to change default 0-100% level (“d00” to “dFF” ) when no DMX input signal.
- Automatic blank screen: short press ◀ or ▶ key to switch enable(“bon”) or disable(“boF”) automatic blank screen.
- Long press M key for 2s or timeout 10s, quit system parameter setting.
DMX mode
- Short press M key, when display 001~512, enter DMX mode.
- Press ◀ or ▶ key to change DMX decode start address(001~512), long press for fast adjustment.
- If there is a DMX signal input, will enter DMX mode automatically.
- DMX Dimming: Each S1-D1 DMX decoder occupy 1 DMX address when connecting the DMX console.
Stand-alone dimmer mode
-
Short press M key, when display L-1~L-8, enter stand-alone dimmer mode.
-
Press ◀ or ▶ key to change dimmer mode number(L-1~L-8).
-
Each dimmer mode can adjust brightness independently.
Long press M key for 2s, prepare for setup brightness.
Press ◀ or ▶ key to setup brightness value(100-1FF).
Long press M key for 2s, or timeout 10s, quit setting. -
Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
Stand-alone dynamic mode
-
Short press M key, when display P-1~P-2, enter stand-alone dynamic mode.
-
Press ◀ or ▶ key to change dynamic mode number(P-1~P-2).
-
Each mode can adjust speed and brightness.
Long press M key for 2s, prepare for setup mode speed, brightness.
Short press M key to switch two item.
Press ◀ or ▶ key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
Long press M key for 2s, or timeout 10s, quit setting. -
Enter stand-alone dynamic mode only when DMX signal is disconnected or lost.
Dynamic mode list
| P-1 | Name |
|---|---|
| P-2 | 0%,50%,100% light change in sequence |
| No. | light fadein and fadeout |
Restore factory default parameter
- Long press ◀ and ▶ key for 2s, restore factory default parameter, display”RES”.
- Factory default parameter: DMX decode mode, DMX decode start address is 1, reverse-phase control, 10% minimum brightness, dimmer mode number is 1, dynamic mode number is 1, output 100% level when no DMX input,disable automatic blank screen.